SIST EN IEC 62386-103:2023
(Main)Digital addressable lighting interface - Part 103: General requirements - Control devices (IEC 62386-103:2022)
Digital addressable lighting interface - Part 103: General requirements - Control devices (IEC 62386-103:2022)
This part of IEC 62386 is applicable to control devices for control by digital signals of electronic lighting equipment.
Digital adressierbare Schnittstelle für die Beleuchtung - Teil 103: Allgemeine Anforderungen - Steuergeräte (IEC 62386-103:2022)
Interface d'éclairage adressable numérique - Partie 103: Exigences générales - Dispositifs de commande (IEC 62386-103:2022)
L'IEC 62386-103:2022 s'applique aux dispositifs de commande par signaux numériques des équipements d'éclairage électroniques. Cette deuxième édition annule et remplace la première édition parue en 2014 et l'Amendement 1:2018. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente:
- le domaine d'application a été mis à jour;
- le mode repos a été mis à jour;
- la durée de sauvegarde de la mémoire non volatile (NVM) a été ajoutée, et la commande SAVE PERSISTENT VARIABLES a été supprimée;
- le bloc de mémoire 0 a été modifié, et les exigences communes pour les blocs de mémoire ont été ajoutées;
- IDENTIFY DEVICE a été mise à jour;
- le numéro de version a été modifié;
- la configuration de l'unité de bus a été ajoutée; et
- les types d'instances et leur configuration ont été ajoutés.
Digitalni naslovljivi vmesnik za razsvetljavo - 103. del: Splošne zahteve - Krmilne naprave (IEC 62386-103:2022)
Ta del standarda IEC 62386 se uporablja za krmilne naprave za krmiljenje elektronske opreme za razsvetljavo z digitalnimi signali.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN IEC 62386-103:2023
01-februar-2023
Nadomešča:
SIST EN 62386-103:2015
SIST EN 62386-103:2015/A1:2019
Digitalni naslovljivi vmesnik za razsvetljavo - 103. del: Splošne zahteve - Krmilne
naprave (IEC 62386-103:2022)
Digital addressable lighting interface - Part 103: General requirements - Control devices
(IEC 62386-103:2022)
Digital adressierbare Schnittstelle für die Beleuchtung - Teil 103: Allgemeine
Anforderungen - Steuergeräte (IEC 62386-103:2022)
Interface d'éclairage adressable numérique - Partie 103: Exigences générales -
Dispositifs de commande (IEC 62386-103:2022)
Ta slovenski standard je istoveten z: EN IEC 62386-103:2022
ICS:
29.140.50 Instalacijski sistemi za Lighting installation systems
razsvetljavo
35.200 Vmesniška in povezovalna Interface and interconnection
oprema equipment
SIST EN IEC 62386-103:2023 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN IEC 62386-103:2023
---------------------- Page: 2 ----------------------
SIST EN IEC 62386-103:2023
EUROPEAN STANDARD EN IEC 62386-103
NORME EUROPÉENNE
EUROPÄISCHE NORM December 2022
ICS 29.140.50; 29.140.99 Supersedes EN 62386-103:2014;
EN 62386-103:2014/A1:2018
English Version
Digital addressable lighting interface - Part 103: General
requirements - Control devices
(IEC 62386-103:2022)
Interface d'éclairage adressable numérique - Partie 103: Digital adressierbare Schnittstelle für die Beleuchtung - Teil
Exigences générales - Dispositifs de commande 103: Allgemeine Anforderungen - Steuergeräte
(IEC 62386-103:2022) (IEC 62386-103:2022)
This European Standard was approved by CENELEC on 2022-12-21. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 62386-103:2022 E
---------------------- Page: 3 ----------------------
SIST EN IEC 62386-103:2023
EN IEC 62386-103:2022 (E)
European foreword
The text of document 34/946/FDIS, future edition 2 of IEC 62386-103, prepared by IEC/TC 34
"Lighting" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
EN IEC 62386-103:2022.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2023-09-21
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2025-12-21
document have to be withdrawn
This document supersedes EN 62386-103:2014 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 62386-103:2022 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standard indicated:
IEC 62386-104:2019 NOTE Harmonized as EN IEC 62386-104:2019 (not modified)
IEC 62386-103:2014 NOTE Harmonized as EN 62386-103:2014 (not modified)
2
---------------------- Page: 4 ----------------------
SIST EN IEC 62386-103:2023
EN IEC 62386-103:2022 (E)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 62386-101 2022 Digital addressable lighting interface - Part EN IEC 62386-101 2022
101: General requirements - System
components
IEC 62386-102 2022 Digital addressable lighting interface - Part EN IEC 62386-102 2022
102: General requirements - Control gear
IEC 62386-3XX series Digital addressable lighting interface - Part EN 62386-3XX series
3XX: Particular requirements for control
devices
3
---------------------- Page: 5 ----------------------
SIST EN IEC 62386-103:2023
---------------------- Page: 6 ----------------------
SIST EN IEC 62386-103:2023
IEC 62386-103
®
Edition 2.0 2022-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Digital addressable lighting interface –
Part 103: General requirements – Control devices
Interface d'éclairage adressable numérique –
Partie 103: Exigences générales – Dispositifs de commande
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.140.50; 29.140.99 ISBN 978-2-8322-5966-5
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN IEC 62386-103:2023
– 2 – IEC 62386-103:2022 © IEC 2022
CONTENTS
FOREWORD . 7
INTRODUCTION . 9
1 Scope . 11
2 Normative references . 11
3 Terms and definitions . 11
4 General . 14
4.1 General . 14
4.2 Version number . 14
5 Electrical specification . 15
6 Bus power supply . 15
7 Transmission protocol structure . 15
7.1 General . 15
7.2 24-bit forward frame encoding . 15
7.2.1 Frame format for instructions and queries . 15
7.2.2 Frame format for event messages. 17
8 Timing . 18
9 Method of operation . 18
9.1 General . 18
9.2 Device features . 18
9.3 Application controller . 18
9.3.1 General . 18
9.3.2 Single-master application controller . 19
9.3.3 Multi-master application controller . 19
9.4 Input device . 20
9.5 Instances of input devices . 20
9.5.1 General . 20
9.5.2 Instance number . 20
9.5.3 Instance type . 20
9.5.4 Instance features . 20
9.5.5 Instance groups . 21
9.6 Commands excluding event messages . 21
9.6.1 General . 21
9.6.2 Device commands . 22
9.6.3 Instance commands . 22
9.6.4 Feature commands . 22
9.7 Event messages . 23
9.7.1 Response to event messages . 23
9.7.2 Device power cycle event . 23
9.7.3 Input notification event . 23
9.7.4 Event message filter . 24
9.8 Input signal, measured value and “inputValue” . 24
9.8.1 General . 24
9.8.2 Input resolution . 24
9.8.3 Getting the input value . 25
9.8.4 Notification of changes . 26
---------------------- Page: 8 ----------------------
SIST EN IEC 62386-103:2023
IEC 62386-103:2022 © IEC 2022 – 3 –
9.9 System failure . 26
9.10 Operating a control device . 26
9.10.1 Enable/disable the application controller . 26
9.10.2 Application controller always active . 26
9.10.3 Enable/disable event messages . 27
9.10.4 Quiescent mode . 27
9.10.5 Modes of operation . 27
9.11 Memory banks . 28
9.11.1 General . 28
9.11.2 Memory map . 29
9.11.3 Selecting a memory bank location . 30
9.11.4 Protectable memory locations . 30
9.11.5 Memory bank reading . 30
9.11.6 Memory bank writing . 32
9.11.7 Memory bank 0 . 33
9.11.8 Memory bank 1 (optional) . 36
9.11.9 Manufacturer-specific memory banks . 37
9.11.10 Reserved memory banks . 37
9.12 Reset . 38
9.12.1 Reset operation . 38
9.12.2 Reset memory bank operation . 38
9.13 Power on behaviour . 38
9.13.1 Power on . 38
9.13.2 Power cycle notification . 39
9.14 Priority use . 39
9.14.1 General . 39
9.14.2 Priority of input notifications . 39
9.15 Assigning short addresses . 40
9.15.1 General . 40
9.15.2 Random address allocation . 40
9.15.3 Identification of a device . 40
9.16 Exception handling . 41
9.17 Device capabilities and status information . 41
9.17.1 Device capabilities . 41
9.17.2 Device status . 41
9.17.3 Instance status . 42
9.18 Non-volatile memory . 42
9.19 Instance types and configuration . 42
9.20 Current bus unit configuration . 43
10 Declaration of variables . 43
11 Definition of commands . 45
11.1 General . 45
11.2 Overview sheets . 45
11.3 Event messages . 52
11.3.1 INPUT NOTIFICATION (device/instance, event) . 52
11.3.2 POWER NOTIFICATION (device) . 52
11.4 Device control instructions . 52
11.4.1 General . 52
11.4.2 IDENTIFY DEVICE . 52
---------------------- Page: 9 ----------------------
SIST EN IEC 62386-103:2023
– 4 – IEC 62386-103:2022 © IEC 2022
11.4.3 RESET POWER CYCLE SEEN . 53
11.5 Device configuration instructions. 53
11.5.1 General . 53
11.5.2 RESET . 53
11.5.3 RESET MEMORY BANK (DTR0) . 54
11.5.4 SET SHORT ADDRESS (DTR0) . 54
11.5.5 ENABLE WRITE MEMORY . 54
11.5.6 ENABLE APPLICATION CONTROLLER . 54
11.5.7 DISABLE APPLICATION CONTROLLER . 54
11.5.8 SET OPERATING MODE (DTR0) . 54
11.5.9 ADD TO DEVICE GROUPS 0-15 (DTR2:DTR1) . 55
11.5.10 ADD TO DEVICE GROUPS 16-31 ( DTR2:DTR1 ) . 55
11.5.11 REMOVE FROM DEVICE GROUPS 0-15 (DTR2:DTR1) . 55
11.5.12 REMOVE FROM DEVICE GROUPS 16-31 (DTR2:DTR1) . 55
11.5.13 START QUIESCENT MODE . 55
11.5.14 STOP QUIESCENT MODE . 55
11.5.15 ENABLE POWER CYCLE NOTIFICATION . 55
11.5.16 DISABLE POWER CYCLE NOTIFICATION . 55
11.5.17 SET EVENT PRIORITY (DTR0) . 55
11.6 Device queries . 56
11.6.1 General . 56
11.6.2 QUERY DEVICE CAPABILITIES . 56
11.6.3 QUERY DEVICE STATUS . 56
11.6.4 QUERY APPLICATION CONTROLLER ERROR . 56
11.6.5 QUERY INPUT DEVICE ERROR . 56
11.6.6 QUERY MISSING SHORT ADDRESS . 57
11.6.7 QUERY VERSION NUMBER . 57
11.6.8 QUERY CONTENT DTR0 . 57
11.6.9 QUERY NUMBER OF INSTANCES . 57
11.6.10 QUERY CONTENT DTR1 . 57
11.6.11 QUERY CONTENT DTR2 . 57
11.6.12 QUERY RANDOM ADDRESS (H) . 57
11.6.13 QUERY RANDOM ADDRESS (M) . 57
11.6.14 QUERY RANDOM ADDRESS (L) . 57
11.6.15 READ MEMORY LOCATION (DTR1, DTR0) . 57
11.6.16 QUERY APPLICATION CONTROLLER ENABLED . 58
11.6.17 QUERY OPERATING MODE . 58
11.6.18 QUERY MANUFACTURER SPECIFIC MODE . 58
11.6.19 QUERY QUIESCENT MODE . 58
11.6.20 QUERY DEVICE GROUPS 0-7 . 58
11.6.21 QUERY DEVICE GROUPS 8-15 . 58
11.6.22 QUERY DEVICE GROUPS 16-23 . 58
11.6.23 QUERY DEVICE GROUPS 24-31 . 58
11.6.24 QUERY POWER CYCLE NOTIFICATION . 58
11.6.25 QUERY EXTENDED VERSION NUMBER(DTR0) . 58
11.6.26 QUERY RESET STATE . 59
11.6.27 QUERY APPLICATION CONTROLLER ALWAYS ACTIVE . 59
11.6.28 QUERY FEATURE TYPE . 59
11.6.29 QUERY NEXT FEATURE TYPE . 59
---------------------- Page: 10 ----------------------
SIST EN IEC 62386-103:2023
IEC 62386-103:2022 © IEC 2022 – 5 –
11.6.30 QUERY EVENT PRIORITY . 59
11.7 Instance control instructions . 59
11.8 Instance configuration instructions . 59
11.8.1 General . 59
11.8.2 ENABLE INSTANCE . 60
11.8.3 DISABLE INSTANCE . 60
11.8.4 SET PRIMARY INSTANCE GROUP (DTR0) . 60
11.8.5 SET INSTANCE GROUP 1 (DTR0) . 60
11.8.6 SET INSTANCE GROUP 2 (DTR0) . 60
11.8.7 SET EVENT SCHEME (DTR0) . 60
11.8.8 SET EVENT PRIORITY (DTR0) . 61
11.8.9 SET EVENT FILTER (DTR2:DTR1:DTR0). 61
11.8.10 SET INSTANCE TYPE (DTR0) . 61
11.8.11 SET INSTANCE CONFIGURATION (DTR0, DTR2:DTR1) . 61
11.9 Instance queries . 62
11.9.1 General . 62
11.9.2 QUERY INSTANCE TYPE . 62
11.9.3 QUERY RESOLUTION . 62
11.9.4 QUERY INSTANCE ERROR . 62
11.9.5 QUERY INSTANCE STATUS . 62
11.9.6 QUERY INSTANCE ENABLED . 62
11.9.7 QUERY PRIMARY INSTANCE GROUP . 62
11.9.8 QUERY INSTANCE GROUP 1 . 63
11.9.9 QUERY INSTANCE GROUP 2 . 63
11.9.10 QUERY EVENT SCHEME . 63
11.9.11 QUERY INPUT VALUE . 63
11.9.12 QUERY INPUT VALUE LATCH . 63
11.9.13 QUERY EVENT PRIORITY . 63
11.9.14 QUERY FEATURE TYPE . 63
11.9.15 QUERY NEXT FEATURE TYPE . 64
11.9.16 QUERY EVENT FILTER 0-7 . 64
11.9.17 QUERY EVENT FILTER 8-15 . 64
11.9.18 QUERY EVENT FILTER 16-23. 64
11.9.19 QUERY INSTANCE CONFIGURATION (DTR0) . 64
11.9.20 QUERY AVAILABLE INSTANCE TYPES . 65
11.10 Special commands . 65
11.10.1 General . 65
11.10.2 TERMINATE . 65
11.10.3 INITIALISE (device) . 65
11.10.4 RANDOMISE . 65
11.10.5 COMPARE . 66
11.10.6 WITHDRAW . 66
11.10.7 SEARCHADDRH (data) . 66
11.10.8 SEARCHADDRM (data) . 66
11.10.9 SEARCHADDRL (data) . 67
11.10.10 PROGRAM SHORT ADDRESS (data) . 67
11.10.11 VERIFY SHORT ADDRESS (data) . 67
11.10.12 QUERY SHORT ADDRESS . 67
11.10.13 WRITE MEMORY LOCATION (DTR1, DTR0, data) . 67
---------------------- Page: 11 ----------------------
SIST EN IEC 62386-103:2023
– 6 – IEC 62386-103:2022 © IEC 2022
11.10.14 WRITE MEMORY LOCATION – NO REPLY (DTR1, DTR0, data) . 68
11.10.15 DTR0 (data) . 68
11.10.16 DTR1 (data) .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.