Source for standards, engineering specifications, manuals and technical publications

This document specifies the method of energy consumption measurement for the following types of industrial trucks as defined in ISO 5053-1: — counterbalance lift truck; — articulated counterbalance lift truck; — reach truck (with retractable mast or fork arm carriage); — straddle truck; — pallet-stacking truck; — pallet truck; — platform and stillage truck; — end-controlled pallet truck; — order-picking truck; — centre-controlled order-picking truck; — towing tractor; — pushing tractor; — burden and personnel carrier; — towing and stacking tractor; — side-loading truck (one side only); — lateral-stacking truck (both sides); — lateral-stacking truck (three sides); — multi-directional lift truck.

This document specifies requirements for high chromium white cast iron grit, as supplied for blast-cleaning processes. It specifies ranges of particle sizes, together with corresponding grade designations. Values are specified for hardness, density, defect/structural requirements, metallographic structure and chemical composition. The requirements specified in this document apply to abrasives supplied in the new condition only. They do not apply to abrasives either during or after use. High chromium white cast iron grits are used in both static and site blasting equipment. They are most often selected where there is a possibility for the recovery and re-use of the abrasive. NOTE 1 Although this document has been developed for preparation of steelwork, these materials are predominantly used for non-ferrous substrates. The properties specified will generally be appropriate for use when preparing other material surfaces, or components, using blast-cleaning techniques, and can be used for applications where no subsequent coating is applied. NOTE 2 Whenever dissimilar metals are used together, galvanic corrosion can occur.

This document specifies requirements and provides recommendations to safeguard the process for the analysis of items of potential forensic value. It includes requirements and recommendations for the selection and application of suitable method(s) for the analysis to meet the needs of the customer and fulfil the request. The requirements are designed to ensure the use of suitable methods, proper controls, qualified personnel and appropriate analytical strategies throughout the forensic analysis of items. This document is applicable to activities conducted by a forensic service provider that occur at the scene and within a facility. This document is applicable to all disciplines of forensic science; however, it is not applicable to the recovery of digital data which is covered by ISO/IEC 27037. The requirements and recommendations facilitate the comprehensive, accurate and reliable analysis of items.

This document specifies requirements and provides recommendations for reporting of forensic work. This document is applicable to the reporting of forensic work performed at a scene and within a facility. The requirements facilitate the preparation and issuing of reports that are accurate, clear, transparent, complete, unambiguous, impartial and suitable for their intended use. This document also includes requirements relating to the review of case records and reports, the issuance and control of reports, and requirements related to testimony.

This document specifies measuring methods for the determination of biobased carbon contents in rubber and rubber products, including polyurethanes. The methods focus on carbon atoms in rubber or rubber products, and determine whether the carbon-containing component is biobased or not, judging from the concentration of 14C, radiocarbon isotope. This document applies to rubber and rubber products such as raw materials, materials and final products.

This specification defines the 3MF file format Core Specification and extensions. It defines all the necessary components that are needed to implement this Suite. This Suite does not change if one or more components are updated by a new edition. The Suite changes only when new components are added to it and/or existing components are removed from it.

This document provides symbols and defines standard datasheets for some of the most often used microfluidic pumps, such as the peristaltic pump, pressure pump, syringe pump and diaphragm/membrane pump.

This document specifies performance tolerances and the technical data presentation for fans of all types. It does not apply for fans designed solely for low-volume air circulation, such as those used for household or similar purposes (ceiling and table fans, extractor fans, etc.). For jet fans, refer to ISO 13350. The upper limit of fan work per unit mass is normally 25 kJ/kg, corresponding to an increase of fan pressure of approximately 30 kPa for a mean density in the fan of 1,2 kg/m3. For higher values, agreement is to be reached between the supplier and the user. This document applies the five installation categories defined in ISO 5801: A free inlet, free outlet; B free inlet, ducted outlet; C ducted inlet, free outlet; D ducted inlet, ducted outlet; E free inlet and free outlet without a partition. The performance of a fan can vary considerably with the installation category it is operating within. Therefore, these categories form an important part of the definition of the fan’s technical data presentation. NOTE International acceptance of the five installation categories provides the opportunity to base a contract on the most appropriate fan category for the end user and the system designer. Correspondingly, the likelihood of the fan providing the agreed performance, without compromise or concession, is enhanced. The efficiency scaling procedures described in 8.1.5 apply to centrifugal fans and axial fans within the specific speed ranges shown in Table 4. To date, there is no experimental data to confirm how they apply to mixed flow fans, having specific speeds in between. Category E fans are treated in Clause 7.

This document specifies methods for the determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) of polymeric materials by means of differential scanning calorimetry (DSC). It is applicable to polyolefin resins that are in a fully stabilized or compounded form, either as raw materials or finished products. It can be applicable to other plastics.

IEC 63270-1:2025 provides guidance on the functional structure model, procedure, method, interface of function blocks. It also offers guidance on data requirements for predictive maintenance of equipment, devices and systems for industrial automation applications. Condition monitoring is not only within the scope of this document but can also be an important input for predictive maintenance.

The purpose of this document is to provide customers and their suppliers with a document specifying the notions of product reliability "construction" and "management".
It offers programme directors and project managers information likely to help them:
-   determine the tasks to be performed and the application procedures, according to the specific nature of the programme and its goals;
-   define and implement the provisions necessary for performing these tasks;
-   within programme execution, situate the various tasks involved in constructing and managing the reliability of a product.
This document applies to all programmes (in particular aeronautical, space and armament programmes).
These reliability construction procedures concern not only all the products and its constituents covered by these programmes, but also the means and manufacturing processes to be implemented for their realization.
The provisions of this document can be negotiated at all levels between the parties directly concerned by a given programme. This implies, on the part of the customer, that each lower level is provided with the information necessary to perform tasks and meet the specified targets.

This document lays down the requirements for the HBES Point API extension to the EN 50090 series, allowing vendor independent communication between smart home and building devices on IPv6 networks.

IEC 62290-2:2025 specifies the functional requirements of UGTMS (urban guided transport management and command/control systems) for use in urban guided passenger transport lines and networks. This document is applicable for new lines or for upgrading existing signalling and command control systems. The IEC 62290 series specifies the functional, system and interface requirements for the command, control, and management systems intended to be used on urban, guided passenger transport lines and networks. These systems are designated herein as urban guided transport management and command/control systems (UGTMS). UGTMS cover a wide range of operations needs from non-automated (GOA1) to unattended (GOA4) operation. A line may be equipped with UGTMS on its full length or only partly equipped. The IEC 62290 series does not specifically address security issues. However, aspects of safety requirements may apply to ensuring security within the urban guided transit system. The main objectives of this series are as follows: * to provide a baseline system description and functional requirements specification for a transport authority to use in a request for proposal, * to provide recommendations for those transport authorities wishing to acquire an interoperable or interchangeable system. It is the responsibility of the transport authority concerned to decide on how to apply the IEC 62290 series and to take into account their particular needs. This document is applicable to applications using * continuous data transmission, * continuous supervision of train movements by train protection profile, and * localisation of trains by onboard UGTMS equipment (reporting trains), and optionally by external wayside (and optionally onboard) device. In this document, the functional requirements set the framework to which detailed functions are added to define any generic or specific application. Because of that, although this document is applicable as a basis to define SRS, FIS and FFFIS, elements can be added for a generic or specific application. This third edition cancels and replaces the second edition published in 2014. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) the functions 5.1.4.5 Stopping a train en route, 5.1.5.4 Monitor speed limit at discrete location, 5.5.5 Manage UGTMS transfer tracks, 5.6.4.1 Monitor passenger emergency calls and 6.2.4 Ensure connecting services have been deleted; b) the functions 5.5.11 Manage train washing, 5.5.12 Manage non-stopping areas and 6.3.4 Perform progressive shutdown have been added; c) many of the requirements have been reworded: changes in their wording could be only minor and editorial, or it could have technical consequences; d) some requirements of the second edition have been moved from one function/subfunction to another; e) some requirements have been deleted; f) some new requirements have been added in the existing functions; g) an informative annex giving the reader some user’s recommendations about this document has been added; h) another informative annex giving some typical performance-related criteria has been also added. i) an informative annex providing a summary of applicability of functions and subfunctions (mandatory or optional) depending on GOA has been added. In order to avoid any disturbance in the use of the document, when functions or requirements of IEC

This document defines the common terms, abbreviations and references used throughout the EN 9300 series of standard parts.

The purpose of this document is to provide customers and their suppliers with a document specifying the notions of “construction” and “management” of product dependability and safety (RAMS).
It offers programme directors and project managers information likely to help them:
—   determine the tasks to be performed and the application procedures, according to the specific nature of the programme and its goals;
—   define and implement the provisions necessary for performing these tasks;
—   within programme execution, situate the various tasks involved in constructing and managing the RAMS of a product.
This document applies to all programmes that involve customer/supplier relation.
RAMS management concerns not only all the products covered by these programmes, but also the components of these products and the production and support resources and processes to be implemented.
The provisions of this document can be negotiated at all levels between the parties directly concerned by a given programme. This implies, on the part of the ordering parties, that each lower level is provided with the information needed to perform the tasks and meet the specified targets. This also implies, on the part of suppliers, an escalation of information pertaining to the RAMS results of the products for which they are responsible.
This document is mainly concerned with the technical aspects, aspects of a legislative (in particular safety at work and regulatory conformity) and confidential nature are not dealt with in this document.

This document specifies a test method for determining the leak tightness and the ease of operation and stop resistance of a valve made of thermoplastic material following an impact applied to the operating device.

This document specifies the characteristics of multilayer mechanical locked floor covering with a wear-resistant and decorative surface layer supplied in panels (either tile or plank form). The floor panels are considered suitable for domestic and commercial levels of use and designed for floating installation.
This document does not apply to resilient floor panels for loose-laying according to EN ISO 20326, to multilayer wood floorings according to EN 13489, to wood veneer floor coverings according to EN 14354, to laminate floor covering according to EN 13329, EN 14978 and EN 15468 nor to products specified in EN ISO 10581, EN ISO 10582, EN ISO 24011, EN 12104 and ISO 14486.
This document is applicable to areas which are subject to frequent wetting, e.g. bathrooms, laundry rooms or saunas, only if specified by the producer.
This document also includes requirements for marking and packaging.
In Annex A (informative), optional properties are given. In Annex B (informative), a test method for the classification of the flexibility is given.