iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 560:2005/AC:2007

(Corrigendum)

Gas welding equipment - Hose connections for equipment for welding, cutting and allied processes

Gas welding equipment - Hose connections for equipment for welding, cutting and allied processes

TC - Figure 4 corrected

Gasschweißgeräte - Schlauchanschlüsse für Geräte und Anlagen für Schweißen, Schneiden und verwandte Prozesse

Matériel de soudage aux gaz - Raccords pour tuyaux souples pour appareils de soudage, coupage et techniques connexes

Oprema za plamensko varjenje - Cevne spojke za opremo za varjenje, rezanje in sorodne postopke

General Information

Status
Withdrawn
Publication Date
23-Oct-2007
Withdrawal Date
11-Sep-2018
ICS
23.040.70 - Hoses and hose assemblies
25.160.30 - Welding equipment
Technical Committee
CEN/TC 121 - Welding
Drafting Committee
CEN/TC 121/SC 7 - Equipment for gas welding, cutting and allied processes
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
12-Sep-2018
Ref Project
SIST EN 560:2005/AC:2008 - Gas welding equipment - Hose connections for equipment for welding, cutting and allied processes

Relations

Replaced By
EN 560:2018 - Gas welding equipment - Hose connections for equipment for welding, cutting and allied processes
Effective Date
19-Sep-2018
Corrects
EN 560:2005 - Gas welding equipment - Hose connections for equipment for welding, cutting and allied processes
Effective Date
08-Jun-2022

Buy Standard

EN 560:2005/AC:2008EN 560:2005/AC:2008
PreviousNext
Corrigendum
EN 560:2005/AC:2008
English, French and German language
3 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Oprema za plamensko varjenje - Cevne spojke za opremo za varjenje, rezanje in sorodne postopkeGasschweißgeräte - Schlauchanschlüsse für Geräte und Anlagen für Schweißen, Schneiden und verwandte ProzesseMatériel de soudage aux gaz - Raccords pour tuyaux souples pour appareils de soudage, coupage et techniques connexesGas welding equipment - Hose connections for equipment for welding, cutting and allied processes83.140.40Gumene ceviHoses25.160.30Varilna opremaWelding equipmentICS:Ta slovenski standard je istoveten z:EN 560:2005/AC:2007SIST EN 560:2005/AC:2008en,fr,de01-januar-2008SIST EN 560:2005/AC:2008SLOVENSKI
STANDARD



SIST EN 560:2005/AC:2008



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 560:2005/ACOctober 2007Octobre 2007Oktober 2007ICS 23.040.70; 25.160.30English versionVersion FrançaiseDeutsche FassungGas welding equipment - Hose connections for equipment for welding,cutting and allied processesMatériel de soudage aux gaz - Raccordspour tuyaux souples pour appareils desoudage, coupage et techniques connexesGasschweißgeräte - Schlauchanschlüssefür Geräte und Anlagen für Schweißen,Schneiden und verwandte ProzesseThis corrigendum becomes effective on 24 October 2007 for incorporation in the three officiallangua
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 560:2018(Main)
Gas welding equipment - Hose connections for equipment for welding, cutting and allied processes
SIST EN 560:2018

This document lays down the dimensions and specifies the characteristics of the constituent parts of hose connections for welding, cutting and allied processes, for example for pressure regulators according to EN ISO 2503 and blowpipes. The suitability of the hose connections mentioned below will be considered according to the applied pressure range. This document does not cover the design of the hose tail inserted into the hose. This is specified in EN 1256.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 14113:2013(Main)
Gas welding equipment - Rubber and plastics hose and hose assemblies for use with industrial gases up to 450 bar (45 MPa) (ISO 14113:2013)
SIST EN ISO 14113:2013

ISO 14113:2013 specifies requirements for rubber and plastics hose and hose assemblies for use with compressed, liquefied, and dissolved gases up to a maximum working pressure of 450 bar (45 MPa), within the ambient temperature range of −20 °C to +60 °C.
It applies to hose assemblies used to connect industrial gas cylinders to manifolds or bundles prior to any pressure reduction stage. It does not cover rubber or thermoplastic hoses for welding, cutting, and allied processes (see ISO 3821 and ISO 12170). It does not apply to refrigerated liquefied gases or to liquefied petroleum gases (LPG).

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
FprEN ISO 3821(Main)
Gas welding equipment - Rubber hoses for welding, cutting and allied processes (ISO/FDIS 3821:2017)
kSIST FprEN ISO 3821:2017
  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 560:2018(Main)
Gas welding equipment - Hose connections for equipment for welding, cutting and allied processes
SIST EN 560:2018

This document lays down the dimensions and specifies the characteristics of the constituent parts of hose connections for welding, cutting and allied processes, for example for pressure regulators according to EN ISO 2503 and blowpipes. The suitability of the hose connections mentioned below will be considered according to the applied pressure range. This document does not cover the design of the hose tail inserted into the hose. This is specified in EN 1256.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 14113:2013(Main)
Gas welding equipment - Rubber and plastics hose and hose assemblies for use with industrial gases up to 450 bar (45 MPa) (ISO 14113:2013)
SIST EN ISO 14113:2013

ISO 14113:2013 specifies requirements for rubber and plastics hose and hose assemblies for use with compressed, liquefied, and dissolved gases up to a maximum working pressure of 450 bar (45 MPa), within the ambient temperature range of −20 °C to +60 °C.
It applies to hose assemblies used to connect industrial gas cylinders to manifolds or bundles prior to any pressure reduction stage. It does not cover rubber or thermoplastic hoses for welding, cutting, and allied processes (see ISO 3821 and ISO 12170). It does not apply to refrigerated liquefied gases or to liquefied petroleum gases (LPG).

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
FprEN ISO 3821(Main)
Gas welding equipment - Rubber hoses for welding, cutting and allied processes (ISO/FDIS 3821:2017)
kSIST FprEN ISO 3821:2017
  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 22435:2024(Main)
Gas cylinders - Cylinder valves with integrated pressure regulators - Specification and type testing (ISO 22435:2024)
kSIST FprEN ISO 22435:2024

This document specifies design, type test methods, marking and instruction requirements for cylinder valves with integrated pressure regulators (VIPRs) intended to be fitted to gas cylinders, pressure drums or tubes or used as a main valve for bundles of cylinders that convey compressed, liquefied or dissolved gases.
These are requirements for VIPRs that are in addition to those given in the relevant closure standard, for example, in ISO 10297 for cylinder valves, in ISO 17871 for quick-release cylinder valves, in ISO 17879 for self-closing cylinder valves or in ISO 23826 for ball valves. For ISO 17871, these requirements are only applicable to quick-release cylinder valves types B, C, D and E.
NOTE 1        If the pressure regulating system of a VIPR is acting as the primary valve operating mechanism, it is covered by the relevant closure standard, e.g. ISO 10297, ISO 17871, ISO 17879 and ISO 23826. This also includes designs where closure of the primary valve operating mechanism of a VIPR is obtained by closing the seat of the pressure regulating system.
NOTE 2        If the primary valve operating mechanism of a VIPR is located at the low-pressure side of the pressure regulating system, it is covered by the relevant closure standard, e.g. ISO 10297, ISO 17871, ISO 17879 and ISO 23826.
NOTE 3        The term “pressure receptacle” is used within this document to cover instances where no differentiation is necessary between gas cylinders, bundles of cylinders, pressure drums and tubes.
This document does not apply to VIPRs for
a)       medical applications (see ISO 10524-3);
b)       liquefied petroleum gas (LPG);
c)        cryogenic applications.
NOTE 4        Additional requirements for a VIPR with a residual pressure device (RPD) are specified in ISO 15996.
NOTE 5        Additional requirements for pressure relief valves can exist in international/regional regulations/ standards.

  • Draft
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17015-1:2024(Main)
Electronic Public Procurement - Catalogue - Part 1: Choreographies
kSIST FprEN 17015-1:2024

The purpose of this deliverable is to specify and describe choreographies for exchanging an electronic product catalogue (“catalogues”) as part of the business processes in the pre-award and post-award area, so that catalogues can serve as a basis for placing orders as well as evaluating tenders. The key aspects covered by this choreography specification are:
-   processes for submitting catalogues from the selling to the buying side;
-   processes for submitting catalogue-related data as part of a tendering process;
-   processes integrating sell-side procurement systems.
This document does not apply to the transactions used in the specified choreographies. These transactions are specified in EN 17015 2. The relationship between the choreographies and the transaction is described in Clause 8.
The identifier of this choreographies document is EN 17015 1:2024.
How to claim compliance to this choreography is specified in 6.2.3.

  • Draft
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO/ASTM 52927:2024(Main)
Additive manufacturing - General principles - Main characteristics and corresponding test methods (ISO/ASTM 52927:2024)
kSIST FprEN ISO/ASTM 52927:2024

This document specifies the principal requirements applied to the testing of parts produced by additive manufacturing processes.
This document
—     identifies quality characteristics for feedstock and parts and the corresponding test procedures,
—     provides the specific procedures to build specimens using additive manufacturing process, and
—     recommends the scope and content of test and supply agreements.
This document is aimed at machine manufacturers, feedstock suppliers, AM system users, part providers, and customers to facilitate the communication on main quality characteristics. It applies wherever additive manufacturing processes are used.
NOTE            It is the intent to include, in future versions of this document, other characteristics such as thermal properties, electrical requirements and physical and physico-chemical properties based upon material types.

  • Draft
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 8362-2:2024(Main)
Injection containers and accessories - Part 2: Closures for injection vials (ISO 8362-2:2024)
SIST EN ISO 8362-2:2024

This document specifies the shape, dimensions, material, performance requirements and labelling of closures for injection vials covered by ISO 8362-1 and ISO 8362-4.
The dimensional requirements are not applicable to barrier-coated closures.
Closures specified in this document are intended for single use only.
NOTE            The potency, purity, stability and safety of a medicinal product during its manufacture and storage can strongly be affected by the nature and performance of the primary packaging.

  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day