EN 14025:2018/AC:2020
(Corrigendum)Tanks for the transport of dangerous goods - Metallic pressure tanks - Design and construction
Tanks for the transport of dangerous goods - Metallic pressure tanks - Design and construction
This document specifies the minimum requirements for the design and construction of metallic pressure tanks having a maximum working pressure exceeding 50 kPa (0,5 bar), for the transport of dangerous goods by road and rail and sea. This document includes requirements for openings, closures and structural equipment; it does not cover requirements of service equipment. For tanks for the transport of cryogenic liquids, EN 13530 1 and EN 13530 2 apply.
Design and construction of pressure tanks according to the Scope of this document are primarily subject to the requirements of RID/ADR, Subsections 6.8.2.1, 6.8.3.1 and 6.8.5, as relevant. In addition, the relevant requirements of RID/ADR, Table A, columns 12 and 13, to Chapters 3.2, 4.3 and Subsection 6.8.2.4 apply. For the structural equipment RID/ADR, Subsections 6.8.2.2 and 6.8.3.2 apply, as relevant. The definitions of RID/ADR, Subsection 1.2.1, are referred to. For portable tanks see also RID/ADR, Chapter 4.2 and Sections 6.7.2 and 6.7.2. In addition, the relevant requirements of RID/ADR, Table A, Columns 10 and 11 to Chapters 3.2, 4.2, and Sections 6.7.2 and 6.7.3 apply. The paragraph numbers above relate to the 2017 issue of RID/ADR which are subject to regular revisions. This can lead to temporary non-compliances with EN 14025.
This document is applicable to liquefied gases including LPG; however for a dedicated LPG standard see EN 12493.
If not otherwise specified, provisions which take up the whole width of the page apply to all kind of tanks. Provisions contained in a single column apply only to:
tanks according to RID/ADR Chapter 6.8 (left-hand column); portable tanks according to RID/ADR Chapter 6.7 (right-hand column).
Tanks für die Beförderung gefährlicher Güter - Metallische Drucktanks - Auslegung und Bau
Citernes pour le transport de matières dangereuses - Citernes métalliques sous pression - Conception et fabrication
Cisterne za prevoz nevarnega blaga - Kovinske tlačne posode - Konstruiranje in izdelava - Popravek AC
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2020
Cisterne za prevoz nevarnega blaga - Kovinske tlačne posode - Konstruiranje in
izdelava - Popravek AC
Tanks for the transport of dangerous goods - Metallic pressure tanks - Design and
construction
Tanks für die Beförderung gefährlicher Güter - Metallische Drucktanks - Auslegung und
Bau
Citernes pour le transport de matières dangereuses - Citernes métalliques sous pression
- Conception et fabrication
Ta slovenski standard je istoveten z: EN 14025:2018/AC:2020
ICS:
13.300 Varstvo pred nevarnimi Protection against dangerous
izdelki goods
23.020.20 Posode in vsebniki, montirani Vessels and containers
na vozila mounted on vehicles
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN 14025:2018/AC
NORME EUROPÉENNE
March 2020
EUROPÄISCHE NORM
ICS 13.300; 23.020.20
English version
Tanks for the transport of dangerous goods - Metallic pressure tanks - Design
and construction
Citernes pour le transport de matières Tanks für die Beförderung gefährlicher Güter
dangereuses - Citernes métalliques sous - Metallische Drucktanks - Auslegung und
pression
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.