iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 8062-3:2007/AC:2009

(Corrigendum)

Geometrical Product Specifications (GPS) - Dimensional and geometrical tolerances for moulded parts - Part 3: General dimensional and geometrical tolerances and machining allowances for castings (ISO 8062-3:2007/Cor 1:2009)

Geometrical Product Specifications (GPS) - Dimensional and geometrical tolerances for moulded parts - Part 3: General dimensional and geometrical tolerances and machining allowances for castings (ISO 8062-3:2007/Cor 1:2009)

ISO - Taking over of an ISO Technical Corrigendum

Geometrische Produktspezifikationen (GPS) - Maß-, Form- und Lagetoleranzen für Formteile - Teil 3: Allgemeine Maß-, Form- und Lagetoleranzen und Bearbeitungszugaben für Gussstücke (ISO 8062-3:2007/Cor 1:2009)

Spécification géométrique des produits (GPS) - Tolérances dimensionnelles et géométriques des pièces moulées - Partie 3: Tolérances dimensionnelles et géométriques générales et surépaisseurs d'usinage pour les pièces moulées (ISO 8062-3:2007/Cor 1:2009)

Geometrijske specifikacije izdelkov - Dimenzijske in geometrijske tolerance zaformanih delov - 3. del: Splošne dimenzijske in geometrijske tolerance in dodatki za obdelavo ulitkov - Popravek AC

General Information

Status
Withdrawn
Publication Date
10-Mar-2009
Withdrawal Date
28-Feb-2023
ICS
17.040.10 - Limits and fits
Technical Committee
CEN/TC 190 - Foundry technology
Drafting Committee
CEN/TC 190 - Foundry technology
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
01-Mar-2023
Ref Project
SIST EN ISO 8062-3:2007/AC:2009 - Geometrical Product Specifications (GPS) - Dimensional and geometrical tolerances for moulded parts - Part 3: General dimensional and geometrical tolerances and machining allowances for castings

Relations

Replaced By
EN ISO 8062-3:2023 - Geometrical product specifications (GPS) - Dimensional and geometrical tolerances for moulded parts - Part 3: General dimensional and geometrical tolerances and machining allowances for castings using ± tolerances for indicated dimensions (ISO 8062-3:2023)
Effective Date
19-Jan-2023
Corrects
EN ISO 8062-3:2007 - Geometrical Product Specifications (GPS) - Dimensional and geometrical tolerances for moulded parts - Part 3: General dimensional and geometrical tolerances and machining allowances for castings (ISO 8062-3:2007)
Effective Date
22-Dec-2008

Buy Standard

EN ISO 8062-3:2007/AC:2009EN ISO 8062-3:2007/AC:2009
PreviousNext
Corrigendum
EN ISO 8062-3:2007/AC:2009
English language
4 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Geometrijske specifikacije izdelkov - Dimenzijske in geometrijske tolerance zaformanih delov - 3. del: Splošne dimenzijske in geometrijske tolerance in dodatki za obdelavo ulitkov - Popravek ACGeometrische Produktspezifikationen (GPS) - Maß-, Form- und Lagetoleranzen für Formteile - Teil 3: Allgemeine Maß-, Form- und Lagetoleranzen und Bearbeitungszugaben für GussstückeSpécification géométrique des produits (GPS) - Tolérances dimensionnelles et géométriques des pièces moulées - Partie 3: Tolérances dimensionnelles et géométriques générales et surépaisseurs d'usinage pour les pièces mouléesGeometrical Product Specifications (GPS) - Dimensional and geometrical tolerances for moulded parts - Part 3: General dimensional and geometrical tolerances and machining allowances for castings17.040.40Geometrical Product Specification (GPS)17.040.10Tolerance in ujemiLimits and fitsICS:Ta slovenski standard je istoveten z:EN ISO 8062-3:2007/AC:2009SIST EN ISO 8062-3:2007/AC:2009en01-junij-2009SIST EN ISO 8062-3:2007/AC:2009SLOVENSKI
STANDARDSIST ISO 8062:19951DGRPHãþD

EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN ISO 8062-3:2007/ACMarch 2009Mars 2009März 2009ICS 17.040.10English versionVersion FrançaiseDeutsche FassungGeometrical Product Specifications (GPS) - Dimensional and geometricaltolerances for moulded parts - Part 3: General dimensional and geometricaltolerances and machining allowances for castings (ISO 8062-3:2007/Cor1:2009)Spécification géométrique des produits(GPS) - Tolérances dimensionnelles etgéométriques des pièces moulées - Partie3: Tolérances dimensionnelles etgéométriques générales et surépaisseursd'usinage pour les pièces moulées (ISO8062-3:2007/Cor 1:2009)Geometrische Produktspezifikationen(GPS) - Maß-, Form- und Lagetoleranzenfür Formteile - Teil 3: Allgemeine Maß-,Form- und Lagetoleranzen undBearbeitungszugaben für Gussstücke (ISO8062-3:2007/Cor 1:2009)This corrigendum becomes effective on 11 March 2009 for incorporation in the three official languageversions of the EN.Ce corrigendum prendra effet le 11 mars 2009 pour incorporation dans les trois versions linguistiquesofficielles de la EN.Die Berichtigung tritt am 11.März 2009 zur Einarbeitung in die drei offiziellen Sprachfassungen derEN in Kraft.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre:
Avenue Marnix 17,
B-1000 Brussels© 2009 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members.Tous droits d'exploitation sous quelque forme et de quelque manière que ce soit réservés dans le monde entier auxmembres nationaux du CEN.Alle Rechte der Verwertung, gleich in welcher Form und in welchem Verfahren, sind weltweit den nationalen Mitgliedernvon CEN vorbehalten.Ref. No.:EN
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 8062-3:2023(Main)
Geometrical product specifications (GPS) - Dimensional and geometrical tolerances for moulded parts - Part 3: General dimensional and geometrical tolerances and machining allowances for castings using ± tolerances for indicated dimensions (ISO 8062-3:2023)
SIST EN ISO 8062-3:2023

This document specifies general dimensional and geometrical tolerances as well as machining allowance grades for castings using ± tolerances for indicated dimensions as delivered to the purchaser according to ISO/TS 8062-2. It is applicable for tolerancing of dimensions and geometry of castings in all cast metals and their alloys produced by various casting manufacturing processes.
This document does not apply to 3D CAD models used without indicated dimensions.
This document applies to both general dimensional and general geometrical tolerances (referred to in or near the title block of the drawing), unless otherwise specified and where specifically referred to on the drawing by one of the references in Clause 11.
The dimensional tolerances covered by this document are tolerances for linear dimensions.
The geometrical tolerances covered by this document are tolerances for:
—     straightness;
—     flatness;
—     roundness;
—     parallelism;
—     perpendicularity;
—     symmetry;
—     coaxiality.
This document does not cover other position tolerances, angular dimensional tolerances or cylindricity tolerances.
This document can be used for the selection of tolerance values for individual indications.

  • Standard
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN ISO/TS 8062-2:2013(Main)
Geometrical Product Specifications (GPS) - Dimensional and geometrical tolerances for moulded parts - Part 2: Rules (ISO/TS 8062-2:2013, Corrected version 2013-11-01)
SIST-TS CEN ISO/TS 8062-2:2014

ISO/TS 8062-2:2013 gives the rules for geometrical dimensioning and tolerancing of final moulded parts and parts machined out of moulded parts. It also gives rules and conventions for the indications of these requirements in technical product documentation and specifies the proportions and dimensions of the graphical symbols to be used.
ISO/TS 8062-2:2013 provides symbols which may be used to identify the relative completeness of the moulded features and parts. These graphical symbols should not be confused with the graphical symbols for surface texture according to ISO 1302, which are notably larger.

  • Technical specification
    65 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Technical specification
    65 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 8062-1:2007(Main)
Geometrical product specifications (GPS) - Dimensional and geometrical tolerances for moulded parts - Part 1: Vocabulary (ISO 8062-1:2007)
SIST EN ISO 8062-1:2007

ISO 8062-1:2007 establishes a vocabulary of terms and definitions used to describe the features, form and tolerance types when assigning dimensional and geometrical tolerances to moulded parts in geometrical product specifications (GPS).

  • Standard
    31 pages
    English and French language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 8062-3:2023(Main)
Geometrical product specifications (GPS) - Dimensional and geometrical tolerances for moulded parts - Part 3: General dimensional and geometrical tolerances and machining allowances for castings using ± tolerances for indicated dimensions (ISO 8062-3:2023)
SIST EN ISO 8062-3:2023

This document specifies general dimensional and geometrical tolerances as well as machining allowance grades for castings using ± tolerances for indicated dimensions as delivered to the purchaser according to ISO/TS 8062-2. It is applicable for tolerancing of dimensions and geometry of castings in all cast metals and their alloys produced by various casting manufacturing processes.
This document does not apply to 3D CAD models used without indicated dimensions.
This document applies to both general dimensional and general geometrical tolerances (referred to in or near the title block of the drawing), unless otherwise specified and where specifically referred to on the drawing by one of the references in Clause 11.
The dimensional tolerances covered by this document are tolerances for linear dimensions.
The geometrical tolerances covered by this document are tolerances for:
—     straightness;
—     flatness;
—     roundness;
—     parallelism;
—     perpendicularity;
—     symmetry;
—     coaxiality.
This document does not cover other position tolerances, angular dimensional tolerances or cylindricity tolerances.
This document can be used for the selection of tolerance values for individual indications.

  • Standard
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 14405-2:2019(Main)
Geometrical product specifications (GPS) - Dimensional tolerancing - Part 2: Dimensions other than linear or angular sizes (ISO 14405-2:2018)
SIST EN ISO 14405-2:2019

This document illustrates the ambiguity caused by the use of dimensional specifications to control properties other than linear or angular size and the benefit of using geometrical specifications instead.
Dimensional tolerancing can be indicated by ± tolerancing or geometrical specifications.
The ambiguity caused by using ± tolerances for dimensions other than linear or angular sizes (for individual tolerances and general tolerances according to, e.g. ISO 2768-1 and ISO 8062-3) is explained in Annex A.
NOTE 1    The figures, as shown in this document, merely illustrate the text and are not intended to reflect actual usage. The figures are consequently simplified to indicate only the relevant principles.
NOTE 2    For indications of dimensional specifications, see the following:
—           ISO 14405-1 for linear size;
—           ISO 14405-3 for angular size;
—           ISO 2538-1 and ISO 2538-2 for wedges;
—           ISO 3040 for cones.
NOTE 3    The rules for geometrical specifications are given in ISO 1101.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 5458:2018(Main)
Geometrical product specifications (GPS) - Geometrical tolerancing - Pattern and combined geometrical specification (ISO 5458:2018)
SIST EN ISO 5458:2018

This document establishes complementary rules to ISO 1101 to be applied to pattern specifications and defines rules to combine individual specifications, for geometrical specifications e.g. using the symbols POSITION, SYMMETRY, LINE PROFILE and SURFACE PROFILE, as well as STRAIGHTNESS (in the case where the toleranced features are nominally coaxial) and FLATNESS (in the case where the toleranced features are nominally coplanar) as listed in Annex C.
These rules apply when a set of tolerance zones are grouped together with location or orientation constraints, through the use of the CZ, CZR or SIM modifiers.
This document does not cover the use of the pattern specifications when the least and maximum material requirement is applied (see ISO 2692).
This document does not cover the establishment of common datum (see ISO 5459) based on pattern features.

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 1101:2017(Main)
Geometrical product specifications (GPS) - Geometrical tolerancing - Tolerances of form, orientation, location and run-out (ISO 1101:2017)
SIST EN ISO 1101:2017

ISO 1101:2017 defines the symbol language for geometrical specification of workpieces and the rules for its interpretation.
It provides the foundation for geometrical specification.
The illustrations in this document are intended to illustrate how a specification can be fully indicated with visible annotation (including e.g. TEDs).
NOTE 1       Other International Standards referenced in Clause 2 and in Tables 3 and 4 provide more detailed information on geometrical tolerancing.
NOTE 2       This document gives rules for explicit and direct indications of geometrical specifications. Alternatively, the same specifications can be indicated indirectly in accordance with ISO 16792 by attaching them to a 3D CAD model. In this case, it is possible that some elements of the specification are available through a query function or other interrogation of information on the model instead of being indicated using visible annotation

  • Standard
    156 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    153 pages
    German language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 1938-2:2017(Main)
Geometrical product specifications (GPS) - Dimensional measuring equipment - Part 2: Reference disk gauges (ISO 1938-2:2017)
SIST EN ISO 1938-2:2017

ISO 1938-2:2017 specifies the most important metrological and design characteristics of reference disk gauges.
ISO 1938-2:2017 covers linear sizes of the gauge up to 500 mm.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    15 pages
    German language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 14405-1:2016(Main)
Geometrical product specifications (GPS) - Dimensional tolerancing - Part 1: Linear sizes (ISO 14405-1:2016)
SIST EN ISO 14405-1:2016

ISO 14405-1:2016 establishes the default specification operator (see ISO 17450‑2) for linear size and defines a number of special specification operators for linear size for features of size, e.g. "cylinder", "sphere", "torus,"[1], "circle", "two parallel opposite planes", or "two parallel opposite straight lines".
It also defines the specification modifiers and the drawing indications for these linear sizes.
It covers the following linear sizes:
a)    local size:
-      two-point size;
-      spherical size;
-      section size;
-      portion size;
b)    global size:
-      direct global linear size:
-      least-squares size;
-      maximum inscribed size;
-      minimum circumscribed size;
-      minimax size;
-      indirect global linear size;
c)    calculated size:
-      circumference diameter;
-      area diameter;
-      volume diameter;
d)    rank-order size:
-      maximum size;
-      minimum size;
-      average size;
-      median size;
-      mid-range size;
-      range of sizes;
-      standard deviation of sizes.
ISO 14405-1:2016 defines tolerances of linear sizes for the following:
-      a + and/or − limit deviation (e.g. 0/−0,019);
-      an upper limit of size (ULS) and/or lower limit of size (LLS) (e.g. 15,2 max., 12 min., or 30,2/30,181);
-      an ISO tolerance class code in accordance with ISO 286‑1 (e.g. 10 h6);
with or without modifiers.
ISO 14405-1:2016 provides a set of tools to express several types of size characteristic. It does not present any information on the relationship between a function or a use and a size characteristic.
[1]         A torus is a feature of size when its directrix diameter is fixed.

  • Standard
    64 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    64 pages
    German language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 1938-1:2015(Main)
Geometrical product specifications (GPS) - Dimensional measuring equipment - Part 1: Plain limit gauges of linear size (ISO 1938-1:2015)
SIST EN ISO 1938-1:2016

ISO 1938-1:2015 specifies the most important metrological and design characteristics of plain limit gauges of linear size.
ISO 1938-1:2015 defines the different types of plain limit gauges used to verify linear dimensional specifications associated with linear size.
ISO 1938-1:2015 also defines the design characteristics and the metrological characteristics for these limit gauges as well as the new or wear limits state Maximum Permissible Limits (MPLs) for the new state or wear limits state for these metrological characteristics.
In addition, ISO 1938-1:2015 describes the use of limit gauges. It covers linear sizes up to 500 mm.

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day