FprEN ISO 13143
(Main)Electronic fee collection - Evaluation of on-board and roadside equipment for conformity to ISO 12813 (ISO/FDIS 13143:2024)
Electronic fee collection - Evaluation of on-board and roadside equipment for conformity to ISO 12813 (ISO/FDIS 13143:2024)
This document specifies the test suite structure (TSS) and test purposes (TPs) for evaluating the conformity of on-board equipment (OBE) and roadside equipment (RSE) to ISO 12813.
It provides a basis for conformance tests for dedicated short-range communication (DSRC) OBE and RSE to support interoperability between different equipment supplied by different manufacturers.
ISO 12813 defines requirements on the compliance check communication (CCC) interface level, but not for the RSE or OBE internal functional behaviour. Consequently, tests regarding OBE and/or RSE functional behaviour remain outside the scope of this document.
Elektronische Gebührenerhebung - Bewertung der Konformität fahrzeuginterner und straßenseitiger Ausrüstung nach ISO 12813 (ISO/FDIS 13143:2024)
Perception de télépéage - Évaluation des équipements embarqués et en bord de route quant à la conformité avec l'ISO 12813 (ISO/FDIS 13143:2024)
Le présent document spécifie la structure de la suite d'essais (TSS, Test Suite Structure) et les buts des essais (TP, Test Purposes) pour évaluer la conformité des équipements embarqués (OBE) et des équipements en bord de route (RSE) par rapport à l'ISO 12813.
Il fournit une base pour les essais de conformité des OBE et RSE de communication dédiée à courte portée (DSRC) afin de permettre l'interopérabilité entre les différents équipements fournis par différents fabricants.
L'ISO 12813 définit les exigences applicables au niveau d'interface de communication de contrôle de conformité CCC mais qui ne concernent pas le comportement fonctionnel interne des RSE et OBE. Par conséquent, les essais relatifs au comportement fonctionnel des OBE et/ou RSE restent en dehors du domaine d'application du présent document.
Elektronsko pobiranje pristojbin - Ugotavljanje skladnosti opreme v vozilu in obcestni napravi s standardom ISO 12813 - 1. del: Zgradba preskuševalnega niza in namen preskušanja (ISO/DIS 13143-1:2023)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-marec-2024
Elektronsko pobiranje pristojbin - Ugotavljanje skladnosti opreme v vozilu in
obcestni napravi s standardom ISO 12813 - 1. del: Zgradba preskuševalnega niza
in namen preskušanja (ISO/DIS 13143-1:2023)
Electronic fee collection - Evaluation of on-board and roadside equipment for conformity
to ISO 12813 - Part 1: Test suite structure and test purposes (ISO/DIS 13143-1:2023)
Elektronische Gebührenerhebung - Bewertung der Konformität fahrzeuginterner und
straßenseitiger Ausrüstung nach ISO 12813 - Teil 1: Struktur und Zweck des
Prüfprogrammes (ISO/DIS 13143-1:2023)
Perception de télépéage - Évaluation des équipements embarqués et en bord de route
quant à la conformité avec l'ISO 12813 - Partie 1: Structure de suite d'essais et buts des
essais (ISO/DIS 13143-1:2023)
Ta slovenski standard je istoveten z: prEN ISO 13143-1
ICS:
03.220.20 Cestni transport Road transport
35.240.60 Uporabniške rešitve IT v IT applications in transport
prometu
43.040.15 Avtomobilska informatika. Car informatics. On board
Vgrajeni računalniški sistemi computer systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT INTERNATIONAL STANDARD
ISO/DIS 13143-1
ISO/TC 204 Secretariat: ANSI
Voting begins on: Voting terminates on:
2023-12-18 2024-03-11
Electronic fee collection — Evaluation of on-board and
roadside equipment for conformity to ISO 12813 —
Part 1:
Test suite structure and test purposes
Perception de télépéage — Évaluation des équipements embarqués et en bord de route quant à la
conformité avec l'ISO 12813 —
Partie 1: Structure de suite d'essais et buts des essais
ICS: 03.220.20; 35.240.60
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 13143-1:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023
ISO/DIS 13143-1:2023(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 13143-1
ISO/TC 204 Secretariat: ANSI
Voting begins on: Voting terminates on:
Electronic fee collection — Evaluation of on-board and
roadside equipment for conformity to ISO 12813 —
Part 1:
Test suite structure and test purposes
Perception de télépéage — Évaluation des équipements embarqués et en bord de route quant à la
conformité avec l'ISO 12813 —
Partie 1: Structure de suite d'essais et buts des essais
ICS: 03.220.20; 35.240.60
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2023
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 13143-1:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023
ISO/DIS 13143-1:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Abbreviated terms . 3
5 Conformance . 4
6 Test suite structure (TSS) . 4
6.1 Structure . 4
6.2 Reference to conformance test specifications . . 5
6.3 Test purposes (TPs) . 5
6.3.1 TP definition conventions . 5
6.3.2 TP naming conventions . 6
Annex A (normative) Test purposes for on-board equipment . 7
Annex B (normative) Test purposes for roadside equipment .48
Annex C (normative) Protocol conformance test report proforma for OBE .66
Annex D (normative) Protocol conformance test report proforma for RSE.73
Bibliography .78
iii
ISO/DIS 13143-1:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 204, Intelligent transport systems, in
collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/TC
278, Intelligent transport systems, in accordance with the Agreement on technical cooperation between
ISO and CEN (Vienna Agreement).
This third edition cancels and replaces the secondedition (ISO 13143-1:2020), which has been
technically revised. In addition, as a result of the withdrawal of ISO 13143-2, the title of this document
is changed to ISO 13141 Electronic fee collection — Evaluation of on-board and roadside equipment for
conformity to ISO 12813.
The main changes compared to the previous edition are as follows:
— amendments to reflect changes to the underlying requirements standards, in particular ISO 12813
and ISO 14906;
— updating of terms and definitions, including the reference to ISO/TS 17573-2 as the primary source;
— updating of data definitions, including the reference to ISO 17573-3 and ISO/FDIS 12813:2023 as the
primary sources;
— amendment of terms to reflect the harmonization of terms across electronic fee collection (EFC)
standards.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
ISO/DIS 13143-1:2023(E)
Introduction
On-board equipment (OBE) that uses satellite-based positioning technology to collect data required for
charging for the use of roads operates in an autonomous way (i.e. without relying on dedicated roadside
infrastructure). The OBE records the amount of road usage in all toll charging systems it passes through.
This document defines the process and tests for evaluation of OBE and roadside equipment (RSE) for
conformity to ISO 12813.
ISO 12813 defines requirements for dedicated short-range communication (DSRC) between OBE and an
interrogator for the purpose of checking conformance of road use with a local toll regime. It assumes an
electronic fee collection (EFC) services architecture according to ISO 17573-1.
This document is intended to:
— assess OBE and RSE capabilities,
— assess OBE and RSE behaviour,
— serve as a guide for OBE and RSE conformance evaluation and type approval,
— achieve comparability between the results of the corresponding tests applied in different places at
different times, and
— facilitate communication between parties.
This document is based on:
— ISO 12813,
— the set of DSRC standards defining the communication stack, and
— ISO/IEC 9646.
v
DRAFT INTERNATIONAL STANDARD ISO/DIS 13143-1:2023(E)
Electronic fee collection — Evaluation of on-board and
roadside equipment for conformity to ISO 12813 —
Part 1:
Test suite structure and test purposes
1 Scope
This document specifies the test suite structure (TSS) and test purposes (TPs) for evaluating the
conformity of on-board equipment (OBE) and roadside equipment (RSE) to ISO 12813.
It provides a basis for conformance tests for dedicated short-range communication (DSRC) OBE and
RSE to support interoperability between different equipment supplied by different manufacturers.
ISO 12813 defines requirements on the compliance check communication (CCC) interface level, but
not for the RSE or OBE internal functional behaviour. Consequently, tests regarding OBE and/or RSE
functional behaviour remain outside the scope of this document.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 3166-1, Codes for the representation of names of countries and their subdivisions — Part 1: Country
code
ISO/FDIS 12813:2023, Electronic fee collection — Compliance check communication for autonomous
systems
ISO 14816, Road transport and traffic telematics — Automatic vehicle and equipment identification —
Numbering and data structure
ISO 14906:2022, Electronic fee collection — Application interface definition for d
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.