EN 13411-3:2004
(Main)Terminations for steel wire ropes - Safety - Part 3: Ferrules and ferrule-securing
Terminations for steel wire ropes - Safety - Part 3: Ferrules and ferrule-securing
This European Standard deals with the requirements for the ferrule-securing of eyes and endless loops.
It also deals with the requirements for ferrules for the ferrule-securing of eyes and endless loops.
This European Standard applies to the ferrule-securing of eye terminations formed either by a Flemish eye or turn-back eye and covers ferrules made of non alloy carbon steel, stainless steel, aluminium and copper.
This European Standard applies to slings and assemblies using steel wire ropes for general lifting applications up to and including 60mm diameter conforming to EN 12385-4, lift ropes conforming to EN 12385-5 and spiral strand ropes conforming to EN 12385-10.
Type testing of ferrule-secured systems and manufacturing quality control requirements are also specified.
This European standard deals with all significant hazards, hazardous situations and events relevant to this particular steel wire rope termination when used as intended and under conditions of use which are foreseeable by the manufacturer.
This standard applies to terminations of steel wire ropes with ferrules and ferrule-securing which are manufactured after the date of this publication.
NOTE One design of ferrule-secured turn-back eye termination using an oval aluminium ferule which satisfies the requirements of this European Standard is given for information in annex A.
Endverbindungen für Drahtseile aus Stahldraht - Sicherheit - Teil 3: Pressklemmen und Verpressen
Diese Europäische Norm behandelt die Anforderungen für das Verpressen von Seilschlaufen und Endlosseilen.
Sie behandelt auch die Anforderungen an die Pressklemmen für das Verpressen von Seilschlaufen und Endlosseilen.
Diese Europäische Norm gilt für das Verpressen von Flämischen Augen und rückgebogenen Seilschlaufen und behandelt Pressklemmen aus unlegiertem Kohlenstoffstahl, nichtrostendem Stahl, Aluminium und Kupfer.
Diese Europäische Norm gilt für Anschlagseile und Stahldrahtseile mit verpresster Seil-Endverbindung für allgemeine Hebezwecke bis zu einem Durchmesser von 60 mm nach EN 12385 4, aus Aufzugsseilen nach EN 12385 5 und Spiralseilen nach EN 12385 10.
Die Baumusterprüfung des Pressklemmensystems und die Anforderungen an die Qualitätskontrolle bei der Herstellung sind ebenfalls festgelegt.
Diese Europäische Norm behandelt alle wesentlichen Gefährdungen, gefährlichen Situationen und Ereignisse, die für diese besondere Seil-Endverbindung von Bedeutung sind, wenn sie wie vorgesehen und unter Bedingungen, wie sie vom Hersteller als vorhersehbar gelten können, angewendet werden.
Diese Norm gilt für Seil-Endverbindungen mit Pressklemmen und für Verpressungen, die nach dem Erscheinungsdatum hergestellt wurden.
ANMERKUNG Eine Ausführung von verpressten rückgebogenen Seilschlaufen, bei der eine ovale Aluminiumpressklemme verwendet wird und die die Anforderungen dieser Europäischen Norm erfüllt, ist in Anhang A zur Information
angegeben.
Terminaisons pour câbles en acier - Sécurité - Partie 3: Manchons et boucles manchonnées
La présente Norme européenne traite des prescriptions relatives au manchonnage des boucles manchonnées et des �illets épissés.
Elle traite également des prescriptions relatives aux manchons utilisés pour le manchonnage des boucles et des �illets épissés.
La présente Norme européenne s'applique au manchonnage des terminaisons à boucle formées d'un �il flamand ou d'une boucle manchonnée à brins parallèles et traite des manchons constitués d'acier au carbone, d'acier inoxydable, d'aluminium et de cuivre non alliés.
La présente Norme européenne s'applique aux élingues et assemblages qui utilisent des câbles en acier pour des applications de levage générales jusqu'à et y compris un diamètre de 60 mm conformément à l'EN 12385-4, des câbles pour ascenseurs conformément à l'EN 12385-5 et des câbles spiraloïdaux conformément à l'EN 12385-10.
Des essais de type des systèmes manchonnés et les prescriptions relatives au contrôle de qualité de fabrication sont également spécifiés.
La présente Norme européenne traite de tous les phénomènes dangereux et de toutes les situations et événements dangereux significatifs correspondant à cette terminaison de câble en acier particulière lorsqu'elle est utilisée tel que prévu et dans les conditions d'utilisation prévisibles par le fabricant.
La présente norme s'applique aux terminaisons de câbles en acier à boucles manchonnées fabriquées après sa date de publication.
NOTE Un modèle de terminaison à boucle manchonnée à brins parallèles utilisant un manchon ovale en aluminium satisfaisant aux prescriptions de la présente Norme européenne est donné pour information dans l'Annexe A.
Zaključki jeklenih žičnih vrvi – Varnost – 3. del: Stisne puše in stiskanje
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2004
=DNOMXþNLMHNOHQLKåLþQLKYUYL±9DUQRVW±GHO 6WLVQHSXãHLQVWLVNDQMH
Terminations for steel wire ropes - Safety - Part 3: Ferrules and ferrule-securing
Endverbindungen für Drahtseile aus Stahldraht - Sicherheit - Teil 3: Pressklemmen und
Verpressen
Terminaisons pour câbles en acier - Sécurité - Partie 3: Manchons et boucles
manchonnées
Ta slovenski standard je istoveten z: EN 13411-3:2004
ICS:
53.020.30 Pribor za dvigalno opremo Accessories for lifting
equipment
77.140.99 Drugi železni in jekleni izdelki Other iron and steel products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 13411-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2004
ICS 53.020.30; 77.140.99
English version
Terminations for steel wire ropes - Safety - Part 3: Ferrules and
ferrule-securing
Terminaisons pour câbles en acier - Sécurité - Partie 3: Endverbindungen für Drahtseile aus Stahldraht - Sicherheit
Manchons et boucles manchonnées - Teil 3: Pressklemmen und Verpressen
This European Standard was approved by CEN on 16 April 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13411-3:2004: E
worldwide for CEN national Members.
Contents
page
Foreword.4
1 Scope .6
2 Normative references .6
3 Terms and definitions .7
4 List of hazards.8
5 Safety requirements and/or measures .8
5.1 Ferrule-secured system .8
5.1.1 General.8
5.1.2 Type testing.9
5.1.3 Instructions to be provided by the ferrule-secured system designer.10
5.2 Ferrules.10
5.2.1 Material .10
5.2.2 Dimensions.10
5.2.3 Manufacture and quality control of ferrule .10
5.2.4 Certificate .11
5.2.5 Marking .11
5.3 Ferrule-securing.11
5.3.1 General.11
5.3.2 Matching of ferrule to wire rope .11
5.3.3 Forming the eye .11
5.3.4 Pressing the ferrule .13
5.3.5 Quality control after pressing of the ferrule .13
6 Verification of the safety requirements and/or measures .14
6.1 Qualification of personnel .14
6.2 Tensile type test (FSET system designer) .14
6.3 Fatigue type test (FSET system designer) .14
6.4 Fatigue type test of Flemish eye ferrule-secured termination of crane hoist rope (FSET system
designer).14
6.5 Ferrule dimensions before pressing (Ferrule manufacturer).14
6.6 Manufacture and quality control of ferrule (Ferrule manufacturer).14
6.7 Ferrules (FSET or ferrule-secured endless loop manufacturer).14
6.8 Matching of ferrule to wire rope (FSET or ferrule-secured endless loop manufacturer) .14
6.9 Forming the eye (FSET or ferrule-secured endless loop manufacturer) .15
6.10 Pressing the ferrule (FSET or ferrule-secured endless loop manufacturer) .15
6.11 Quality control after pressing the ferrule(s) (FSET or ferrule-secured endless loop
manufacturer).15
7 Information for use .15
7.1 Marking .15
7.2 Certificate .15
Annex A (informative) Specification for one design of turn-back eye ferrule-secured termination.16
A.1 General.16
A.2 Types of terminations .16
A.3 Ropes for this design of ferrule .18
A.3.1 General.18
A.3.2 Rope types.18
A.3.3 Metallic cross sectional area factor.18
A.3.4 Rope grade .18
A.3.5 Types of rope lay .18
A.4 Tubing.18
A.4.1 General.18
A.4.2 Material .18
A.4.3 Straightness .18
A.4.4 Wall thickness.19
A.5 Identification and dimensions of ferrules (unpressed) .19
A.6 Matching wire rope to ferrule .22
A.7 Making the eye termination .25
A.7.1 Positioning of ferrule (Types A and B).25
A.7.2 Pressing the ferrule.25
A.7.3 Ferrules after pressing.25
A.8 Information for use .27
A.8.1 Identification marks.27
A.8.2 Temperature limits.27
Annex ZA (informative) Relationship of this European Standard with EU Directives.28
Bibliography.29
Foreword
This document (EN 13411-3:2004) has been prepared by Technical Committee CEN/TC 168 “Chains, ropes,
webbing, slings and accessories - Safety”, the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by December 2004, and conflicting national standards shall be withdrawn at the latest
by December 2004.
This document has been prepared under a mandate given to CEN by the European Commission and the European
Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.
Annex A is informative.
EN 13411 consists of the following parts:
Part 1: Thimbles for steel wire rope slings
Part 2: Splicing of eyes for wire rope slings
Part 3: Ferrules and ferrule-securing
Part 4: Metal and resin socketing
Part 5: U-bolt wire rope grips
Part 6: Asymmetric wedge socket
Part 7: Symmetric wedge socket
This is the first edition of this Part of this European Standard.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark,
Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Introduction
This European Standard is a Type C Standard as stated in EN 1070
This European Standard has been prepared to provide a means of conforming with the essential requirements of
the Machinery Directive and associated EFTA regulations.
Purchasers ordering to this standard are advised to specify in their purchasing contract that the supplier operates
an independently verified quality assurance system to ensure themselves that products claimed to comply
consistent
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.