oSIST prEN 545:2026

Ductile iron pipes, fittings, accessories and their joints for water pipelines - Requirements and test methods

This European Standard specifies the requirements and associated test methods applicable to ductile iron pipes, fittings, accessories and their joints for the construction of pipelines outside buildings:
-   to convey different types of water (e.g. raw water, treated water, re-used water) for all types of applications (e.g. water intended for human consumption, for fire protection, for snow making, for irrigation, for hydro-electricity etc.);
-   with or without pressure;
-   to be installed below or above ground.
This European Standard is applicable to pipes, fittings and accessories which are:
-   manufactured with socketed, flanged or spigot ends;
-   supplied externally and internally coated;
-               suitable for fluid temperatures between 0 °C and 50 °C, excluding frost;
-   not intended for use in areas subject to fire regulations.
NOTE 1   This does not preclude special arrangements for the products to be used at higher temperatures.
This European Standard covers pipes and fittings cast by any type of foundry process or manufactured by fabrication of cast components, as well as corresponding joints and accessories, in a size range extending from DN 40 to DN 2 000, inclusive.
This European Standard specifies requirements for materials, dimensions and tolerances, mechanical properties and standard coatings of ductile iron pipes and fittings. It also gives performance requirements for all components including joints. Joint design and gasket shapes are outside the scope of this standard.
In addition, reference is made to the performance requirements of couplings, flange adaptors and saddles manufactured for use with ductile iron pipes and fittings.
NOTE 2   In this European Standard, all pressures are relative pressures, expressed in bars (100 kPa = 1 bar).

Rohre, Formstücke, Zubehörteile aus duktilem Gusseisen und ihre Verbindungen für Wasserleitungen - Anforderungen und Prüfverfahren

This document specifies the requirements and associated test methods applicable to ductile iron pipes, fittings, accessories and their joints for the construction of pipelines outside buildings:
   to convey different types of water (e.g. raw water, treated water, re-used water) for all types of applications (e.g. water intended for human consumption, for fire protection, for snow making, for irrigation, for hydro-electricity etc.);
   with or without pressure;
   to be installed below or above ground.
This document is applicable to pipes, fittings and accessories which are:
   manufactured with socketed, flanged or spigot ends;
   supplied externally and internally coated;
   suitable for fluid temperatures between 0 °C and 50 °C, excluding frost;
   not intended for use in areas subject to reaction to fire regulations.
This does not preclude special arrangements for the products to be used at higher temperatures.
This document covers pipes and fittings cast by any type of foundry process or manufactured by fabrication of cast components, as well as corresponding joints and accessories, in a size range extending from DN 40 to DN 2 000, inclusive.
This document specifies requirements for materials, dimensions and tolerances, mechanical properties and standard coatings of ductile iron pipes and fittings. It also gives performance requirements for all components including joints. Joint design and gasket shapes are outside the scope of this document.
In addition, reference is made to the minimum performance requirements of couplings, flange adaptors and saddles manufactured for use with ductile iron pipes and fittings.
NOTE   In this document, all pressures are relative pressures, expressed in bars (100 kPa = 1 bar).

Tuyaux, raccords et accessoires en fonte ductile et leurs assemblages pour canalisations d'eau - Prescriptions et méthodes d'essai

Cevi, fitingi, pribor in spoji iz duktilne železove litine za vodovodno omrežje - Zahteve in preskusne metode

Ta evropski standard določa zahteve in povezane preskusne metode, ki se uporabljajo za duktilne litoželezne cevi, fazonske kose, dodatke in njihove spoje za gradnjo cevovodov zunaj stavb:
- za prenos različnih vrst vode (npr. surova voda, obdelana voda, ponovno uporabljena voda) za vse vrste uporabe (npr. voda namenjena za človeško potrošnjo, za protipožarno zaščito, za izdelavo snega, za namakanje, za hidroelektrarne itd.);
- z ali brez tlaka;
- za vgradnjo pod ali nad zemljo.
Ta evropski standard se uporablja za cevi, fazonske kose in dodatke, ki so:
- izdelani z vtičnimi, prirobničnimi ali gladkimi konci;
- dobavljeni z zunanjim in notranjim premazom;
- primerni za temperature tekočin med 0 °C in 50 °C, brez zmrzali;
- niso namenjeni za uporabo na območjih, kjer veljajo požarni predpisi.
OPOMBA 1 To ne izključuje posebnih dogovorov za izdelke, ki se uporabljajo pri višjih temperaturah.
Ta evropski standard zajema cevi in fazonske kose, ulite s katerim koli postopkom livarne ali izdelane z obdelavo ulitih komponent, kot tudi ustrezne spoje in dodatke, v velikostnem razponu od DN 40 do DN 2 000, vključno.
Ta evropski standard določa zahteve za materiale, dimenzije in tolerance, mehanske lastnosti in standardne premaze duktilnih litoželeznih cevi in fazonskih kosov. Prav tako določa zahteve glede zmogljivosti za vse komponente, vključno s spoji. Oblikovanje spojev in oblike tesnil so zunaj obsega tega standarda.
Poleg tega se sklicuje na zahteve glede zmogljivosti spojk, adapterjev za prirobnice in sedel, izdelanih za uporabo z duktilnimi litoželeznimi cevmi in fazonskimi kosi.
OPOMBA 2 V tem evropskem standardu so vsi tlaki relativni tlaki, izraženi v barih (100 kPa = 1 bar).

General Information

• Status: Not Published
• Public Enquiry End Date: 02-Aug-2026
• ICS: 23.040.03 - Pipeline and its parts for external water conveyance systems
• ICS: 23.040.10 - Iron and steel pipes
• ICS: 23.040.40 - Metal fittings
• ICS: 91.140.60 - Water supply systems
• Technical Committee: TLP - Pressure vessels
• Current Stage: 4020 - Public enquire (PE) (Adopted Project)
• Start Date: 04-Jun-2026
• Due Date: 22-Oct-2026
• Ref Project: prEN 545 - Ductile iron pipes, fittings, accessories and their joints for water pipelines - Requirements and test methods

Relations

• Revises: SIST EN 545:2011 - Ductile iron pipes, fittings, accessories and their joints for water pipelines - Requirements and test methods
• Effective Date: 01-Jul-2026

Overview

oSIST prEN 545:2026 is the latest draft European Standard developed by SIST for ductile iron pipes, fittings, accessories, and their joints used in water pipeline systems. It specifies comprehensive requirements and associated test methods for the construction of water pipelines outside buildings. The standard covers components designed to convey various types of water-including raw, treated, and re-used water-for diverse applications such as human consumption, fire protection, irrigation, hydro-electricity, and snowmaking.

This standard is applicable to ductile iron pipes, fittings, and accessories manufactured with socketed, flanged, or spigot ends, with external and internal coatings, and suitable for fluid temperatures between 0°C and 50°C (excluding frost conditions). Intended for both above-ground and below-ground pipeline installations, oSIST prEN 545:2026 provides essential criteria for product quality, safety, and performance under varying operational conditions.

Key Topics

• Scope of Application: Covers ductile iron pipes, fittings, and accessories for water transportation in a size range from DN 40 to DN 2000.
• Water Types & Uses: Applicable for pipelines conveying potable water, raw water, re-used water, fire protection, irrigation, snowmaking, and hydro-electrical uses, with or without operating pressure.
• Product Construction: Includes components produced by casting or fabrication, with socketed, flanged, or spigot ends.
• Material and Coating Requirements: Sets out the essential material properties and standard requirements for external and internal coatings to ensure long-term durability and corrosion resistance.
• Mechanical Properties: Specifies mechanical criteria, including tensile strength and hardness.
• Dimensional and Tolerance Settings: Defines requirements for wall thickness, diameter, length, and straightness to support interoperability and reliability.
• Performance Testing: Details methods for leak tightness, compressive strength of cement mortar linings, and mechanical resistance of joints and accessories.
• Installation Environment: Suitable for pipes installed above or below ground but not intended for areas covered by fire safety regulations.
• Conformity and Quality Assurance: Provides guidelines for conformity assessment, initial type testing, and factory production controls.

Applications

oSIST prEN 545:2026 supports a wide range of practical applications focused on the construction and maintenance of reliable, safe water pipeline infrastructure:

• Public Water Supply Systems: Ensures the safe transport of drinking water through the use of ductile iron pipes with proven material and performance standards.
• Fire Protection Networks: Suitable for robust and long-lasting firewater distribution systems, essential in municipal and industrial settings.
• Agricultural Irrigation: Facilitates efficient irrigation networks by specifying durable and high-integrity pipeline components.
• Industrial Water Pipelines: Used in systems carrying water for processing, cooling, or hydro-electric power generation.
• Specialty Applications: Supports pipelines for snowmaking and reused water, contributing to sustainability and resource efficiency in recreational and environmental management.
• Non-pressurized and Pressurized Systems: Adaptable to both pressurized and gravity-fed networks, increasing design flexibility.

Related Standards

• EN 196-1: Methods of testing cement-relevant to internal linings.
• EN 197 Series: Specifications for cement types used in pipeline linings.
• EN 681-1: Material requirements for elastomeric seals in pipe joints.
• EN 1092-2: Specifications for cast iron flanges and their joints.
• EN 14901-1/2: Requirements and test methods for organic coatings of ductile iron fittings and accessories.
• EN 15655 Series: Standards for organic linings in ductile iron pipe systems.
• EN ISO 6506-1 & 6892-1: Metallic material property testing (Brinell hardness, tensile testing).
• EN ISO 7091 & 8673: Fastener components for secure pipeline assembly.

By aligning with oSIST prEN 545:2026, manufacturers, utilities, and water infrastructure planners ensure pipeline products meet stringent European benchmarks for durability, safety, and public health, supporting long-term reliability in water distribution networks.

Standards Content (Sample)

SLOVENSKI STANDARD
01-julij-2026
Cevi, fitingi, pribor in spoji iz duktilne železove litine za vodovodno omrežje -
Zahteve in preskusne metode
Ductile iron pipes, fittings, accessories and their joints for water pipelines - Requirements
and test methods
Rohre, Formstücke, Zubehörteile aus duktilem Gusseisen und ihre Verbindungen für
Wasserleitungen - Anforderungen und Prüfverfahren
Tuyaux, raccords et accessoires en fonte ductile et leurs assemblages pour
canalisations d'eau - Prescriptions et méthodes d'essai
Ta slovenski standard je istoveten z: prEN 545
ICS:
23.040.10 Železne in jeklene cevi Iron and steel pipes
23.040.40 Kovinski fitingi Metal fittings
91.140.60 Sistemi za oskrbo z vodo Water supply systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2026
ICS 23.040.03; 23.040.10; 23.040.40 Will supersede EN 545:2010
English Version
Ductile iron pipes, fittings, accessories and their joints for
water pipelines - Requirements and test methods
Tuyaux, raccords et accessoires en fonte ductile et Rohre, Formstücke, Zubehörteile aus duktilem
leurs assemblages pour canalisations d'eau - Gusseisen und ihre Verbindungen für Wasserleitungen
Prescriptions et méthodes d'essai - Anforderungen und Prüfverfahren
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 203.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2026 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 545:2026 E
worldwide for CEN national Members.

Contents Page
European foreword . 8
1 Scope . 9
2 Normative references . 9
3 Terms and definitions . 10
4 Technical requirements. 14
4.1 General . 14
4.1.1 Ductile iron pipes, fittings and accessories . 14
4.1.2 Surface condition and repair . 15
4.1.3 Types of joints and interconnection . 15
4.1.4 Materials in contact with water intended for human consumption . 16
4.2 Pressure class . 16
4.3 Dimensional requirements. 16
4.3.1 Pipes and fittings thickness . 16
4.3.2 Diameter . 17
4.3.3 Length . 18
4.3.4 Straightness of pipes . 20
4.4 Material characteristics . 20
4.4.1 Tensile properties. 20
4.4.2 Hardness . 21
4.5 Coatings and linings for pipes. 21
4.5.1 General . 21
4.5.2 Metallic zinc-based coating with finishing layer . 22
4.5.3 Internal lining of cement mortar . 23
4.6 Coatings for fittings and accessories . 24
4.6.1 General . 24
4.6.2 Paint coating . 25
4.7 Marking of pipes, fittings and accessories . 25
4.7.1 Pipes and fittings . 25
4.7.2 Accessories . 25
4.8 Leak tightness . 26
5 Performance requirements for joints and pipe saddles . 26
5.1 General . 26
5.2 Flexible joints . 26
5.2.1 General . 26
5.2.2 Test conditions . 27
5.2.3 Test parameters. 27
5.3 Restrained flexible joints . 28
5.4 Flanged joints as cast, screwed, welded and adjustable . 28
5.5 Pipe saddles . 29
5.5.1 Test conditions . 29
5.5.2 Annulus . 29
6 Test methods . 30
6.1 Pipe dimensions . 30
6.1.1 Wall thickness . 30
6.1.2 External diameter . 30
6.1.3 Internal diameter . 30
6.1.4 Length . 30
6.2 Straightness of pipes . 31
6.3 Tensile testing of ductile iron components . 31
6.3.1 Samples . 31
6.3.2 Preparation of test bar. 31
6.3.3 Apparatus and test method . 32
6.3.4 Test results . 32
6.4 Brinell hardness of ductile iron components . 33
6.5 Works leak tightness test for pipes and fittings . 33
6.5.1 General . 33
6.5.2 Centrifugally cast pipes . 33
6.5.3 Pipes not centrifugally cast, fittings and accessories . 33
6.6 Metallic zinc or alloy of zinc and aluminium mass . 33
6.7 Thickness of paint coatings . 34
6.8 Thickness of cement mortar lining . 34
7 Performance test methods . 35
7.1 Compressive strength of the cement mortar lining . 35
7.2 Leak tightness of flexible joints . 35
7.2.1 General . 35
7.2.2 Leak tightness of flexible joints to positive internal pressure . 36
7.2.3 Leak tightness of flexible joints to negative internal pressure . 37
7.2.4 Leak tightness of flexible push-in joints to positive external pressure . 37
7.2.5 Leak tightness of flexible joints to dynamic internal pressure . 37
7.3 Leak tightness and mechanical resistance of flanged joints . 38
7.4 Leak tightness and mechanical resistance of pipe saddles . 39
7.4.1 Positive internal pressure . 39
7.4.2 Negative internal pressure . 39
8 Tables of dimensions . 40
8.1 Socket and spigot pipes . 40
8.2 Flanged pipes . 42
8.3 Fittings for socketed joints . 42
8.3.1 General . 42
8.3.2 43
8.3.3 44
8.3.4 45
8.3.5 46
8.3.6 46
8.3.7 48
8.3.8 48
8.3.9 50
8.3.10 51
8.3.11 Double socket tees with flanged branch, DN 300 to DN 700 . 52
8.3.12 Double socket tees with flanged branch DN 800 to DN 2 000 . 54
8.3.13 55
8.4 Fittings for flanged joints . 56
8.4.1 General . 56
8.4.2 57
8.4.3 57
8.4.4 58
8.4.5 59
8.4.6 60
8.4.7 61
8.4.8 All flanged tees, DN 300 to DN 700 . 62
8.4.9 All flanged tees, DN 800 to DN 2000 . 63
8.4.10 64
8.4.11 66
8.4.12 66
8.4.13 67
8.4.14 68
8.4.15 69
8.4.16 69
8.4.17 70
8.4.18 71
9 Evaluation of conformity . 71
9.1 General . 71
9.2 Initial performance testing . 72
9.2.1 General . 72
9.2.2 Characteristics . 72
9.2.3 Treatment of calculated values and design . 72
9.2.4 Sampling, testing and conformity criteria . 72
9.3 Factory production control (FPC) . 73
9.3.1 General . 73
9.3.2 FPC requirements for all manufacturers . 74
9.3.3 Manufacturer-specific FPC system requirements . 75
Annex A (normative) Allowable pressures . 77
A.1 General . 77
A.2 Socket and spigot pipes (see 8.1) . 77
A.3 Fittings for socketed joints (see 8.3) . 77
A.4 Flanged pipes (see 8.2) and fittings for flanged joints (see 8.4) . 78
A.5 Accessories . 78
Annex B (informative) Longitudinal bending resistance of pipes . 79
Annex C (informative) Diametral stiffness of pipes . 80
Annex D (informative) Optional coatings . 83
D.1 Pipes . 83
D.2 Fittings and accessories . 84
Annex E (informative) Field of use in relation to the characteristics of soils. 85
E.1 Metallic zinc . 85
E.2 Alloy of zinc and aluminium with or without other metals . 85
E.3 Heavy duty coatings . 85
Annex F (informative) Field of use, water characteristics . 87
Annex G (informative) Calculation method of buried pipelines, heights of cover . 88
G.1 Calculation method . 88
G.1.1 Calculation formula . 88
G.1.2 Pressure from earth loading . 88
G.1.3 Pressure from traffic loading . 89
G.1.4 Bedding factor, K . 89
G.1.5 Factor of lateral pressure, f . 89
G.1.6 Modulus of soil reaction, E'. 89
G.2 Heights of cover . 90
Annex H (informative) EN and ISO Standards cross references for ductile iron pipes and
fittings . 91
Bibliography . 92

Tables
Table 1 — Limit deviations on thickness of fittings . 17
Table 2 — Limit deviation on internal diameter . 18
Table 3 — Maximum DN for limit deviations on internal diameter for pressure classes . 18
Table 4 — Standardized lengths of socket and spigot pipes . 18
Table 5 — Standardized lengths of flange pipes . 19
Table 6 — Permissible deviation on lengths of fittings . 20
Table 7 — Limit deviations on length . 20
Table 8 — Tensile properties . 21
Table 9 — Thickness of cement mortar lining . 24
Table 10 — DN groupings for performance tests . 26
Table 11 — Performance tests for joints . 27
Table 12 — Bending moments for flange joint performance tests . 29
Table 13 — Performance tests for pipe saddles . 30
Table 14 — Dimensions of test bar . 32
Table 15 — Works test pressure for pipes not centrifugally cast, fittings and accessories . 33
Table 16 — Dimensions of pipes of preferred pressure classes . 40
Table 17 — Dimensions of pipes . 41
Table 18 — Dimensions of flanged sockets . 43
Table 19 — Dimensions of flanged spigots and collars . 45
Table 20 — Dimensions of double socket 90° and 45° bends . 47
Table 21 — Dimensions of double socket 22,5)° and 11,25° bends . 49
Table 22 — Dimensions of all socket tees . 50
Table 23 — Dimensions of double socket tees with flanged branch, DN 40 to 250 . 51
Table 24 — Dimensions of double socket tees with flanged branch, DN 300 to DN 700 . 52
Table 25 — Dimensions of double socket tees with flanged branch, DN 800 to DN 2 000 . 54
Table 26 — Dimensions of double socket tapers . 55
Table 27 — Dimensions of double flanged 90° and 90° duckfoot bends . 57
Table 28 — Dimensions of double flanged 45° bends . 58
Table 29 — Dimensions of double flanged 22,5° and 11,25° bends . 60
Table 30 — Dimensions of all flanged tees, DN 40 to DN 250. 61
Table 31 — Dimensions of all flanged tees, DN 300 to DN 700 . 62
Table 32 — Dimensions of all flanged tees, DN 800 to DN 2000 . 63
Table 33 — Dimensions of double flanged tapers . 65
Table 34 — Dimensions of PN 10 and PN 16 blank flanges . 66
Table 35 — Dimensions of PN 25 and PN 40 blank flanges . 68
Table 36 — Dimensions of PN 10 and PN 16 reducing flanges . 70
Table 37 — Dimensions of PN 25 and PN 40 reducing flanges . 71
Table 38 — Number of test samples for initial performance testing . 73
Table 39 — Minimum frequency of product testing as part of FPC . 74
Table 40 — Maximum batch sizes for tensile testing . 75
Table A.1 — Fittings pressure class . 78
Table A.2 — Flanged pipe and fittings pressures . 78
Table B.1 — Longitudinal bending moment resistance of pipes . 79
Table C.1 — Diametral stiffness of pipes of preferred pressure classes . 81
Table F.1 — Field of use for cement mortar linings (not exhaustive) . 87
Table G.1 — Heights of cover for pipes of preferred pressure classes . 90

Figures
Figure 1 — Leak tightness test of joints (internal pressure) . 36
Figure 2 — Leak tightness test of joints (external pressure) . 37
Figure 3 — Strength and leak tightness test for flanged joints . 38
Figure 4 — Leak tightness test for pipe saddles . 39
Figure 5 — Socket and spigot pipes . 40
Figure 6 — Flanged sockets . 43
Figure 7 — Flanged spigots . 44
Figure 8 — Collars . 45
Figure 9 — Double socket 90° (1/4) bends . 46
Figure 10 — Double socket 45° (1/8) bends . 46
Figure 11 — Double socket 22°30′ (1/16) bends . 48
Figure 12 — Double socket 11°15′ (1/32) bends . 48
Figure 13 — All socket tees . 50
Figure 14 — Double socket tees with flanged branch . 51
Figure 15 — Double socket tapers . 55
Figure 16 — Double flanged 90° (1/4) bends . 57
Figure 17 — Double flanged duckfoot 90° (1/4) bends . 57
Figure 18 — Double flanged 45° (1/8) bends . 58
Figure 19 — Double flanged 22°30′ (1/16) bends . 59
Figure 20 — Double flanged 11°15′ (1/32) bends . 60
Figure 21 — All flanged tees . 61
Figure 22 — Double flanged tapers . 64
Figure 23 — Blank flanges PN 10 . 66
Figure 24 — Blank flanges PN 16 . 66
Figure 25 — Blank flanges PN 25 . 67
Figure 26 — Blank flanges PN 40 . 68
Figure 27 — Reducing flanges PN 10 . 69
Figure 28 — Reducing flanges PN 16 . 69
Figure 29 — Reducing flanges PN 25 . 70
Figure 30 — Reducing flanges PN 40 . 71

European foreword
This document (prEN 545:2026) has been prepared by Technical Committee CEN/TC 203 “Cast iron
pipes, fittings and their joints”, the secretariat of which is held by AFNOR.
This document ci currently submitted to the CEN Enquiry.
This document will supersede EN 545:2010.
In this document Annex A is normative and Annexes B, C, D, E, F, G and H are informative.
This standard is in conformity with the general requirements already established by CEN/TC 164 in the
field of water supply.
In respect of potential adverse effects on the quality of water intended for human consumption, caused
by the products covered by this standard:
— this standard provides no information as to whether the products may be used without restriction in
any of the member states of the EU or EFTA;
— it should be noted that, while awaiting the implementation of European criteria, existing national
regulations concerning the use and/or the characteristics of these products remain in force.

1 Scope
This document specifies the requirements and associated test methods applicable to ductile iron pipes,
fittings, accessories and their joints for the construction of pipelines outside buildings:
— to convey different types of water (e.g. raw water, treated water, re-used water) for all types of
applications (e.g. water intended for human consumption, for fire protection, for snow making, for
irrigation, for hydro-electricity etc.);
— with or without pressure;
— to be installed below or above ground.
This document is applicable to pipes, fittings and accessories which are:
— manufactured with socketed, flanged or spigot ends;
— supplied externally and internally coated;
— suitable for fluid temperatures between 0 °C and 50 °C, excluding frost;
— not intended for use in areas subject to reaction to fire regulations.
This does not preclude special arrangements for the products to be used at higher temperatures.
This document covers pipes and fittings cast by any type of foundry process or manufactured by
fabrication of cast components, as well as corresponding joints and accessories, in a size range extending
from DN 40 to DN 2 000, inclusive.
This document specifies requirements for materials, dimensions and tolerances, mechanical properties
and standard coatings of ductile iron pipes and fittings. It also gives performance requirements for all
components including joints. Joint design and gasket shapes are outside the scope of this document.
In addition, reference is made to the minimum performance requirements of couplings, flange adaptors
and saddles manufactured for use with ductile iron pipes and fittings.
NOTE In this document, all pressures are relative pressures, expressed in bars (100 kPa = 1 bar).
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
EN 196-1, Methods of testing cement — Part 1: Determination of strength
EN 197-1, Cement — Part 1: Composition, specifications and conformity criteria for common cements
EN 197-5, Cement — Part 5: Portland-composite cement CEM II/C-M and Composite cement CEM VI
EN 681-1, Elastomeric seals — Material requirements for pipe joint seals used in water and drainage
applications — Part 1: Vulcanized rubber
EN 1092-2, Flanges and their joints — Circular flanges for pipes, valves, fittings and accessories, PN
designated — Part 2: Cast iron flanges
EN 14901-1, Ductile iron pipes, fittings and accessories — Requirements and test methods for organic
coatings of ductile iron fittings and accessories – Part 1: Epoxy coating (heavy duty)
EN 14901-2, Ductile iron pipes, fittings and accessories — Requirements and test methods for organic
coatings of ductile iron fittings and accessories — Part 2: Thermoplastic acid modified polyolefin coating
(TMPO)
EN 15655-1, Ductile iron pipes, fittings and accessories — Requirements and test methods for organic
linings of ductile iron pipes and fittings — Part 1: Polyurethane lining of pipes and Fittings
EN 15655-2, Ductile iron pipes, fittings and accessories — Requirements and test methods for organic
linings of ductile iron pipes and fittings — Part 2: Thermoplastic Acid Modified Polyolefin (TMPO) lining of
pipes
EN ISO 4016, Fasteners — Hexagon head bolts — Product grade C (ISO 4016)
EN ISO 6506-1, Metallic materials — Brinell hardness test — Part 1: Test method (ISO 6506-1)
EN ISO 6892-1, Metallic materials — Tensile testing — Part 1: Method of test at room temperature
EN ISO 7091, Plain washers — Normal series — Product grade C (ISO 7091)
EN ISO 8673, Fasteners — Hexagon regular nuts (style 1), with fine pitch thread (ISO 8673:2023)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
ductile iron
cast iron used for pipes, fittings and accessories in which graphite is present substantially in spheroidal
form
3.2
pipe
casting of uniform bore, straight in axis, having socket, spigot or flanged ends, except for flanged socket
pieces, flanged spigot pieces and collars which are classified as fittings
3.3
fitting
casting other than a pipe which allows pipeline deviation, change of direction or bore
Note 1 to entry: In addition flanged socket pieces, flanged spigot pieces and collars are also classified as fittings.
3.4
accessory
any casting/fabrication other than a pipe or fitting which is intended for use in a ductile iron pipeline
including:
— glands and bolts for mechanical flexible joints (see 3.14);
— glands, bolts and locking rings for restrained flexible joints (see 3.15);
— pipe saddles for service pipe connections;
— adjustable flanges and flanges to be welded or screwed;
— flange adaptors for use with ductile iron pipes and fittings (see 4.1.3.2);
— couplings for use with ductile iron pipes and fittings (see 4.1.3.2)
Note 1 to entry: Valves of all types are not covered by the term accessory.
Note 2 to entry: Wide tolerance flange adaptors and couplings are covered by EN 14525.
3.5
component
any product defined in 3.2 to 3.4
3.6
flange
end of a pipe, fitting or accessory extending perpendicular to its axis, with bolt holes equally spaced on a
circle
Note1 to entry: A flange can be fixed (e.g. integrally cast, screwed or welded) or adjustable; an adjustable flange
comprises a ring, in one or several parts assembled together, which bears on an end joint hub and can be freely
rotated around the barrel axis before jointing.
3.7
spigot
male end of a pipe or fitting
3.8
spigot end
maximum insertion depth of the spigot plus 50 mm
3.9
socket
female end of a component to make the connection with the spigot of the next component
3.10
gasket
sealing component of a joint
3.11
joint
connection between the ends of two components in which a gasket is used to affect a seal
3.12
flexible joint
joint which permits significant angular deflection both during and after installation and which can accept
a slight offset of the centreline
3.13
push-in flexible joint
flexible joint assembled by pushing the spigot through the gasket in the socket of the mating component
3.14
mechanical flexible joint
flexible joint in which sealing is obtained by applying pressure to the gasket by mechanical means, e.g. a
gland
3.15
restrained flexible joint
flexible joint in which a means is provided to prevent separation of the assembled joint
3.16
flanged joint
joint between two flanged ends
3.17
nominal size
DN
alphanumerical designation of size for components of a pipework system, to be used for reference
purposes, which comprises the letters DN followed by a dimensionless whole number which is indirectly
related to the physical size, in millimetres, of the bore or outside diameter of the end connections
[SOURCE: EN ISO 6708:1995]
3.18
nominal pressure
PN
alphanumerical designation related to a combination of mechanical and dimensional characteristics of a
component of a pipework system, to be used for reference purposes, which comprises the letters PN
followed by a dimensionless number
[SOURCE: EN 1333:2006]
Note 1 to entry: All components of the same nominal size DN and designated by the same PN number have
compatible mating dimensions.
3.19
leak tightness test pressure
pressure applied to a component during manufacture in order to ensure its leak tightness
3.20
allowable operating pressure
PFA
maximum hydrostatic pressure that a component is capable of withstanding continuously in service
[SOURCE: EN 805:2025]
3.21
pressure class
C
alphanumerical designation of a family of components, including their joints, relating to their operating
pressures as verified by all the performance tests described in this standard, which includes the letter C
followed by a dimensionless number equal to the maximum PFA in bars of the family of components
3.22
allowable maximum operating pressure
PMA
maximum pressure occurring from time to time, including surge, that a component is capable of
withstanding in service
[SOURCE: EN 805:2025]
3.23
allowable test pressure
PEA
maximum hydrostatic pressure that a newly installed component is capable of withstanding for a
relatively short duration, in order to insure the integrity and tightness of the pipeline
[SOURCE: EN 805:2025]
Note 1 to entry: This test pressure is different from the system test pressure (STP), which is related to the design
pressure of the pipeline and is intended to ensure its integrity and leak tightness.
3.24
diametral stiffness of a pipe
characteristic of a pipe which allows it to resist ovalization under loading when installed
3.25
performance test
proof of design test which is done once and shall be repeated after each change of design
3.26
laying length
length by which a pipeline progresses when an additional pipe or fitting is installed
Note 1 to entry: For socketed pipes and fittings the laying length L is equal to the overall length (OL)
e
minus the maximum spigot insertion depth (X) as given by the manufacturer. For flanged pipes and
fit
...