SIST EN ISO 10855-3:2025
(Main)Offshore containers and associated lifting sets - Part 3: Periodic inspection, examination and testing (ISO 10855-3:2024)
Offshore containers and associated lifting sets - Part 3: Periodic inspection, examination and testing (ISO 10855-3:2024)
This document specifies requirements for the periodic inspection, examination and testing of offshore freight and service containers, built in accordance with ISO 10855‑1, with maximum a gross mass not exceeding 25 000 kg and their associated lifting sets, intended for repeated use to, from and between offshore installations and ships. Inspection requirements following damage and repair of offshore containers are also included.
Recommended knowledge and experience of staff responsible for inspection of offshore containers is given in Annex B.
Recommended knowledge and experience of staff responsible for inspection of lifting sets intended for use with offshore containers is given in Annex C.
Offshore-Container und dazugehörige Anschlaggarnituren - Teil 3: Wiederkehrende Kontrolle, Inspektion und Prüfung (ISO 10855-3:2024)
Dieses Dokument legt Anforderungen für die wiederkehrende Kontrolle, Inspektion und Prüfung von Offshore-Containern fest, die nach ISO 10855 1 gebaut wurden und deren maximale Bruttomasse 25 000 kg nicht übersteigt sowie für die zugehörigen Anschlaggarnituren, die zur wiederholten Verwendung für den Transport zu, von und zwischen Offshore-Anlagen und Schiffen vorgesehen sind, fest. Anforderungen an die Inspektion nach Beschädigung und Reparatur von Offshore-Containern sind ebenfalls enthalten.
Containeurs offshore et dispositifs de levage associés - Partie 3: Contrôle périodique, inspection et essais (ISO 10855-3:2024)
Le présent document spécifie les exigences relatives au contrôle périodique, à l'inspection et aux essais des conteneurs de marchandises et de service, construits conformément à l'ISO 10855‑1, ayant une masse brute maximale inférieure ou égale à 25 000 kg et leurs dispositifs de levage associés, destinés à un usage répété à destination, en provenance ou entre des installations en mer et des navires. Les exigences relatives à l'inspection après des dommages et une réparation des conteneurs offshore sont également incluses.
Les connaissances et l'expérience recommandées du personnel en charge de l'inspection des conteneurs offshore sont indiquées à l'Annexe B.
Les connaissances et l'expérience recommandées du personnel en charge de l'inspection des dispositifs de levage sont indiquées à l'Annexe C.
Plavajoče kontejnerske enote in z njimi povezan dvižni pribor - 3. del: Periodični nadzor, pregled in preskušanje (ISO 10855-3:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2025
Plavajoče kontejnerske enote in z njimi povezan dvižni pribor - 3. del: Periodični
nadzor, pregled in preskušanje (ISO 10855-3:2024)
Offshore containers and associated lifting sets - Part 3: Periodic inspection, examination
and testing (ISO 10855-3:2024)
Offshore-Container und dazugehörige Anschlaggarnituren - Teil 3: Wiederkehrende
Kontrolle, Inspektion und Prüfung (ISO 10855-3:2024)
Containeurs offshore et dispositifs de levage associés - Partie 3: Contrôle périodique,
inspection et essais (ISO 10855-3:2024)
Ta slovenski standard je istoveten z: EN ISO 10855-3:2024
ICS:
53.020.99 Druga dvigalna oprema Other lifting equipment
55.180.10 Večnamenski kontejnerji General purpose containers
75.180.10 Oprema za raziskovanje, Exploratory, drilling and
vrtanje in odkopavanje extraction equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 10855-3
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2024
EUROPÄISCHE NORM
ICS 55.180.10; 75.180.10 Supersedes EN ISO 10855-3:2018
English Version
Offshore containers and associated lifting sets - Part 3:
Periodic inspection, examination and testing (ISO 10855-
3:2024)
Conteneurs pour une utilisation en mer et dispositifs Offshore-Container und dazugehörige
de levage associés - Partie 3: Contrôle périodique, Anschlaggarnituren - Teil 3: Wiederkehrende
inspection et essais (ISO 10855-3:2024) Kontrolle, Inspektion und Prüfung (ISO 10855-3:2024)
This European Standard was approved by CEN on 18 November 2024.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10855-3:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 10855-3:2024) has been prepared by Technical Committee ISO/TC 67 "Oil and
gas industries including lower carbon energy" in collaboration with Technical Committee CEN/TC 12
“Oil and gas industries including lower carbon energy” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2025, and conflicting national standards shall be
withdrawn at the latest by May 2025.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 10855-3:2018.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 10855-3:2024 has been approved by CEN as EN ISO 10855-3:2024 without any
modification.
International
Standard
ISO 10855-3
Second edition
Offshore containers and associated
2024-11
lifting sets —
Part 3:
Periodic inspection, examination
and testing
Conteneurs pour une utilisation en mer et dispositifs de levage
associés —
Partie 3: Contrôle périodique, inspection et essais
Reference number
ISO 10855-3:2024(en) © ISO 2024
ISO 10855-3:2024(en)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 10855-3:2024(en)
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Symbols and abbreviated terms. 2
5 Container inspection plate . 2
5.1 General .2
5.2 Contents of inspection plate .3
6 Schedule of periodic inspection/examination and test — Containers . 3
7 Container lifting test . 4
7.1 General .4
7.2 Test equipment and calibration .5
8 Non-destructive examination (NDE) of welds . 5
8.1 General .5
8.2 NDE methods.5
8.3 Use of Eddy current testing at periodic inspections .5
8.4 NDE operators .6
9 Visual inspection . 6
9.1 General .6
9.2 Markings .6
9.3 Welds .6
9.4 Pad eyes and lashing points .6
9.5 Structure .6
9.6 Door closures .6
9.7 Floor .6
10 Marking of the inspection plate . 7
11 Inspection report . 7
12 Record keeping . 7
13 Damage and repair procedures . 7
14 Schedule of inspection/examination and test — Lifting sets . 8
15 Inspection of attachment of lifting set to an offshore container .11
15.1 Attachment .11
15.2 Inspection report .11
15.3 Record keeping .11
16 Pre-trip inspections .11
16.1 General .11
16.2 Pre-trip inspection. 12
Annex A (informative) Regulations for offshore containers .13
Ann
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.