SIST EN ISO 81714-1:2010
(Main)Design of graphical symbols for use in the technical documentation of products - Part 1: Basic rules (ISO 81714- 1:2010)
Design of graphical symbols for use in the technical documentation of products - Part 1: Basic rules (ISO 81714- 1:2010)
This part of ISO 81714 specifies basic rules for the design of graphical symbols for use in the technical documentation of products, taking into account basic application needs.
Gestaltung von graphischen Symbolen für die Anwendung in der technischen Produktdokumentation - Teil 1: Grundregeln (ISO 81714-1:2010)
Dieser Teil der ISO 81714 legt unter Berücksichtigung von grundlegenden Anwendungsanforderungen
Grundregeln für die Gestaltung von graphischen Symbolen für die Anwendung in der technischen Produktdokumentation
fest.
ANMERKUNG Zusätzliche Anforderungen an in hoch entwickelten CAD-Systemen angewendete
graphische Symbole sind in den Teilen 2 und 3 dieser Normenreihe festgelegt.
Création de symboles graphiques à utiliser dans la documentation technique de produits - Partie 1: Règles fondamentales (ISO 81714-1:2010)
L'ISO 81714-1:2010 établit les règles fondamentales relatives à la création de symboles graphiques à utiliser dans la documentation technique de produits en tenant compte des besoins fondamentaux d'application.
Načrtovanje grafičnih simbolov za uporabo v tehnični dokumentaciji izdelkov - 1. del: Osnovna pravila (ISO 81714-1:2010)
Ta del ISO 81714 opredeljuje osnovna pravila za načrtovanje grafičnih simbolov za uporabo v tehnični dokumentaciji izdelkov, z upoštevanjem osnovnih uporabniških potreb.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 81714-1:2010
01-september-2010
1DGRPHãþD
SIST EN ISO 81714-1:2003
1DþUWRYDQMHJUDILþQLKVLPERORY]DXSRUDERYWHKQLþQLGRNXPHQWDFLMLL]GHONRY
GHO 2VQRYQDSUDYLOD ,62
Design of graphical symbols for use in the technical documentation of products - Part 1:
Basic rules (ISO 81714- 1:2010)
Gestaltung von graphischen Symbolen für die Anwendung in der technischen
Produktdokumentation - Teil 1: Grundregeln (ISO 81714-1:2010)
Création de symboles graphiques à utiliser dans la documentation technique de produits
- Partie 1: Règles fondamentales (ISO 81714-1:2010)
Ta slovenski standard je istoveten z: EN ISO 81714-1:2010
ICS:
01.080.01 *UDILþQLVLPEROLQDVSORãQR Graphical symbols in general
01.110 7HKQLþQDGRNXPHQWDFLMD]D Technical product
L]GHONH documentation
SIST EN ISO 81714-1:2010 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 81714-1:2010
---------------------- Page: 2 ----------------------
SIST EN ISO 81714-1:2010
EUROPEAN STANDARD
EN ISO 81714-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2010
ICS 01.110; 01.080.01 Supersedes EN ISO 81714-1:1999
English Version
Design of graphical symbols for use in the technical
documentation of products - Part 1: Basic rules (ISO 81714-
1:2010)
Création de symboles graphiques à utiliser dans la Gestaltung von graphischen Symbolen für die Anwendung
documentation technique de produits - Partie 1: Règles in der technischen Produktdokumentation - Teil 1:
fondamentales (ISO 81714-1:2010) Grundregeln (ISO 81714-1:2010)
This European Standard was approved by CEN on 26 May 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 81714-1:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 81714-1:2010
EN ISO 81714-1:2010 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 81714-1:2010
EN ISO 81714-1:2010 (E)
Foreword
This document (EN ISO 81714-1:2010) has been prepared by Technical Committee ISO/TC 10 "Technical
product documentation".
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by December 2010, and conflicting national standards shall be withdrawn
at the latest by December 2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 81714-1:1999.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 81714-1:2010 has been approved by CEN as a EN ISO 81714-1:2010 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 81714-1:2010
---------------------- Page: 6 ----------------------
SIST EN ISO 81714-1:2010
INTERNATIONAL ISO
STANDARD 81714-1
Second edition
2010-06-15
Design of graphical symbols for use in
the technical documentation of
products —
Part 1:
Basic rules
Création de symboles graphiques à utiliser dans la documentation
technique de produits —
Partie 1: Règles fondamentales
Reference number
ISO 81714-1:2010(E)
©
ISO 2010
---------------------- Page: 7 ----------------------
SIST EN ISO 81714-1:2010
ISO 81714-1:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 81714-1:2010
ISO 81714-1:2010(E)
Contents Page
Foreword .iv
1 Scope.1
2 Normative references.1
3 Terms and definitions .1
4 Markers.2
5 Design of graphical symbols.3
5.1 Graphic representation.3
5.2 Design procedure .3
6 Design principles.3
6.1 Shape.3
6.2 Operational state .4
6.3 Classes of graphical symbols.4
6.4 Combination of graphical symbols .4
6.5 Grid; module .7
6.6 Line width and module size.7
6.7 Lines and arcs .7
6.8 Minimum space between parallel lines .8
6.9 Hatched and filled areas .8
6.10 Connect node.8
6.11 Position of a connect node.8
6.12 Terminal line .8
6.13 Reference point .9
6.14 Text assigned to graphical symbols .9
6.15 Size of graphical symbols .10
6.16 Symbol identifier .10
7 Modification of proportions.10
8 Variants of graphical symbols .10
Bibliography.14
© ISO 2010 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 81714-1:2010
ISO 81714-1:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 81714-1 was prepared jointly by Technical Committees ISO/TC 10, Technical product documentation,
Subcommittee SC 10, Process plant documentation and tpd-symbols, and IEC/TC 3, Information structures,
documentation and graphical symbols. The draft was circulated for voting to the national bodies of both ISO
and IEC.
This second edition of ISO 81714-1 cancels and replaces the first edition (ISO 81714-1:1999), which has been
technically revised.
ISO 81714 consists of the following parts, under the general title Design of graphical symbols for use in the
technical documentation of products:
⎯ Part 1: Basic rules
IEC 81714 consists of the following parts, under the general title Design of graphical symbols for use in the
technical documentation of products:
⎯ Part 2: Specification for graphical symbols in a computer sensible form, including graphical symbols for a
reference library, and requirements for their interchange
⎯ Part 3: Classification of connect nodes, networks and their encoding
iv © ISO 2010 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 81714-1:2010
INTERNATIONAL STANDARD ISO 81714-1:2010(E)
Design of graphical symbols for use in the technical
documentation of products —
Part 1:
Basic rules
1 Scope
This part of ISO 81714 specifies basic rules for the design of graphical symbols for use in the technical
documentation of products, taking into account basic application needs.
NOTE Supplementary requirements for graphical symbols used in advanced computer-aided design systems are
specified in IEC 81714-2 and IEC 81714-3.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 129-1, Technical drawings — Indication of dimensions and tolerances — Part 1: General principles
ISO 6428, Technical drawings — Requirements for microcopying
ISO/IEC 8859 (all parts), Information technology — 8-bit single-byte coded graphic character sets
ISO/IEC 10367, Information technology — Standardized coded graphic character sets for use in 8-bit codes
ISO/IEC 10646, Information technology — Universal Multiple-Octet Coded Character Set (UCS)
ISO 80000-2, Quantities and units — Part 2: Mathematical signs and symbols to be used in the natural
sciences and technology
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
graphical symbol
visually perceptible figure with a particular meaning used to transmit information independently of language
[6]
[ISO 17724:2003 , 31]
NOTE 1 The graphical symbol may represent objects of interest, such as products, functions or requirements for
manufacturing, quality control, etc.
NOTE 2 A graphical symbol is not to be confused with the simplified representation of products which is normally
drawn to scale and which can look like a graphical symbol.
© ISO 2010 – All rights reserved 1
---------------------- Page: 11 ----------------------
SIST EN ISO 81714-1:2010
ISO 81714-1:2010(E)
3.2
reference point
origin of the coordinate system used in the description of all the graphical elements of the graphical symbol
NOTE The reference point can be used for positioning and transformation, e.g. by creation of a mirror image, rotation,
and displacement.
3.3
symbol family
set of graphical symbols with a common conception using graphical characteristics with specific meanings
3.4
connect node
location on a graphical symbol intended for connection
3.5
terminal line
line of a graphical symbol ending at a connect node
NOTE Most graphical symbols of non-electric character are not provided with terminal lines; most graphical symbols
of electric character are provided with terminal lines.
3.6
text
data in the form of characters, symbols, words, phrases, paragraphs, sentences, tables, or other character
arrangements, intended to convey a meaning, and whose interpretation is essentially based upon the reader's
knowledge of some natural language or artificial language
[3]
[ISO/IEC 2382-1:1993 , 01.01.03]
3.7
arc
curved line with no inflection point
3.8
variant
〈graphical symbols〉 alternative graphical symbol design for a given referent
[6]
[ISO 17724:2003 , 79]
EXAMPLE An identified orientation of a graphical symbol with regard to the flow direction or transfer direction.
NOTE A variant can be based on the rotation and/or creation of a mirror image of the corresponding symbol, together
with possibly other modifications such as relocation of inputs and outputs and reorientation of text.
4 Markers
In this part of ISO 81714, the marker shown in Figure 1 is used to illustrate positions of connect nodes.
Figure 1 — Marker
2 © ISO 2010 – All rights reserved
---------------------- Page: 12 ----------------------
SIST EN ISO 81714-1:2010
ISO 81714-1:2010(E)
5 Design of graphical symbols
5.1 Graphic representation
Graphical symbols shall be designed to convey information concerning a function or a special requirement.
This also applies when physical products are to be represented by graphical symbols.
5.2 Design procedure
The design
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.