Marking of electrical and electronic equipment (EEE) in respect to separate collection of waste EEE (WEEE)

This document specifies a marking
— of electrical and electronic equipment (EEE) with a view to minimizing the disposal of waste EEE (WEEE)
as unsorted waste and to facilitating its separate collection.
NOTE 1 This is in accordance with Article 14(4) of Directive 2012/19/EU (WEEE, recast)
— that serves to clearly identify the producer of the equipment and
— that the equipment has been put on the market after 13 August 2005.
NOTE 2 This is in accordance with Articles 12(3) and 15(2) of Directive 2012/19/EU (WEEE, recast)
— that applies to categories of electrical and electronic equipment subject to WEEE collection, treatment,
recovery and environmentally sound disposal as defined by European and national regulations, provided
the equipment concerned is not part of another type of equipment that does not fall within the scope of
above mentioned regulations.
NOTE 3 This is in accordance with Article 2 and Annexes I – IV of Directive 2012/19/EU (WEEE, recast) [1]
The definition of a technical carrier medium for machine based identifying the producer, such as a barcode,
electronic data medium or microchip, is not covered by this document.

Kennzeichnung von Elektro- und Elektronikgeräten für eine getrennte Sammlung von Elektro- und Elektronik-Altgeräten (WEEE)

Marquage des équipements électriques et électroniques pour la collecte séparée des déchets EEE (DEEE)

Le présent document spécifie un marquage
—   des équipements électriques et électroniques (EEE) en vue de réduire au minimum l'élimination des déchets EEE (DEEE) avec les déchets non triés et de faciliter leur collecte séparée.
NOTE 1   Ceci conformément à l’Article 14(4) de la directive 2012/19/UE (DEEE, refonte;)
—   qui sert à identifier clairement le producteur de l’équipement et
—   que cet équipement a été mis sur le marché après le 13 août 2005.
NOTE 2   Ceci conformément aux Articles 12(3) et 15(2) de la directive 2012/19/UE (DEEE, refonte);
—   qui s'applique aux catégories d'équipements électriques et électroniques soumis à la collecte, au traitement, à la valorisation et à l'élimination respectueuse de l'environnement des DEEE, tels que définis par les réglementations européennes et nationales, à condition que l'équipement concerné ne soit pas intégré à un autre type d'équipement exclu du domaine d'application des réglementations susmentionnées.
NOTE 3   Ceci conformément à l’Article 2 et aux Annexes I à IV de la directive 2012/19/UE (DEEE, refonte) [1]
La définition d'un support technique pour l’identification du producteur par le biais d’une machine, tel qu'un code-barres, un support de données électronique ou une micropuce, n'est pas couverte par le présent document.

Označevanje električne in elektronske opreme glede na ločeno zbiranje odpadkov EEE (WEEE)

Ta dokument določa označevanje:
– električne in elektronske opreme (EEE) z namenom, da se zmanjša odlaganje odpadne električne in elektronske opreme (WEEE) kot nesortiranega odpadka ter omogoči njeno ločeno zbiranje.
OPOMBA 1: To je v skladu s členom 14(4) Direktive 2012/19/EU o odpadni električni in elektronski opremi (prenovljena različica);
– pri katerem sta jasno navedena proizvajalec opreme in
– datum, ko je bila oprema dana na trg, tj. po 13. avgustu 2005.
OPOMBA 2: To je v skladu v členoma 12(3) in 15(2) Direktive 2012/19/EU o odpadni električni in elektronski opremi (prenovljena različica);
– ki se uporablja za kategorije električne in elektronske opreme, za katere veljajo zbiranje, obdelava, predelava ter okolju prijazno odlaganje odpadne električne in elektronske opreme, kot to določajo evropski in nacionalni predpisi, pod pogojem, da zadevna oprema ni del druge vrste opreme, ki ne spada na področje uporabe zgoraj omenjenih predpisov.
OPOMBA 3: To je v skladu s členom 2 in dodatki I–IV Direktive 2012/19/EU [1] o odpadni električni in elektronski opremi (prenovljena različica) [1].
Opredelitev tehničnega nosilca za strojno prepoznavanje proizvajalca, kot je črtna koda, elektronski nosilec podatkov ali mikročip, v tem dokumentu ni zajeta.

General Information

Status
Published
Public Enquiry End Date
31-Dec-2021
Publication Date
16-Aug-2022
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
19-Jul-2022
Due Date
23-Sep-2022
Completion Date
17-Aug-2022

Relations

Buy Standard

Standard
SIST EN 50419:2022
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
oSIST prEN 50419:2021
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 50419:2022
01-oktober-2022
Nadomešča:
SIST EN 50419:2006
Označevanje električne in elektronske opreme glede na ločeno zbiranje odpadkov
EEE (WEEE)

Marking of electrical and electronic equipment (EEE) in respect to separate collection of

waste EEE (WEEE)
Ta slovenski standard je istoveten z: EN 50419:2022
ICS:
01.080.20 Grafični simboli za posebno Graphical symbols for use on
opremo specific equipment
13.030.30 Posebni odpadki Special wastes
29.020 Elektrotehnika na splošno Electrical engineering in
general
31.020 Elektronske komponente na Electronic components in
splošno general
SIST EN 50419:2022 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 50419:2022
---------------------- Page: 2 ----------------------
SIST EN 50419:2022
EUROPEAN STANDARD EN 50419
NORME EUROPÉENNE
EUROPÄISCHE NORM July 2022
ICS 01.080.40; 29.020; 31.020 Supersedes EN 50419:2006
English Version
Marking of electrical and electronic equipment (EEE) in respect
to separate collection of waste EEE (WEEE)

Marquage des équipements électriques et électroniques Kennzeichnung von Elektro- und Elektronikgeräten für eine

pour la collecte séparée des déchets EEE (DEEE) getrennte Sammlung von Elektro- und Elektronik-Altgeräten

This European Standard was approved by CENELEC on 2022-06-06. CENELEC members are bound to comply with the CEN/CENELEC

Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC

Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation

under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the

same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,

Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the

Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,

Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.

Ref. No. EN 50419:2022 E
---------------------- Page: 3 ----------------------
SIST EN 50419:2022
EN 50419:2022 (E)
Contents Page

European foreword ............................................................................................................................................. 3

Introduction ......................................................................................................................................................... 4

1 Scope ...................................................................................................................................................... 5

2 Normative references ............................................................................................................................ 5

3 Terms and definitions ........................................................................................................................... 5

4 Marking ................................................................................................................................................... 6

4.1 Requirements of marking of EEE ......................................................................................................... 6

4.1.1 Unique identification of the producer .................................................................................................. 6

4.1.2 Identification of date of put on the market for financial differentiation needs of WEEE ............... 6

4.1.3 Marking that the EEE is subject to separate WEEE collection ......................................................... 7

4.2 Design of the marking ........................................................................................................................... 7

4.2.1 Integrated marking ................................................................................................................................ 7

4.2.2 Separate markings ................................................................................................................................. 9

4.2.3 General marking design requirements ................................................................................................ 9

4.2.4 Location of the marking ........................................................................................................................ 9

Bibliography ...................................................................................................................................................... 10

Figures

Figure 1 — Marking of electrical and electronic equipment as required by 4.1 b) 2) .......................................... 8

Figure 2 — Crossed-out wheeled bin symbol ...................................................................................................... 9

---------------------- Page: 4 ----------------------
SIST EN 50419:2022
EN 50419:2022 (E)
European foreword
This document (EN 50419:2022) has been prepared by CLC/TC 111X “Environment”.
The following dates are fixed:
• latest date by which this document has to be (dop) 2023-06-06
implemented at national level by publication of
an identical national standard or by
endorsement
• latest date by which the national standards (dow) 2025-06-06
conflicting with this document have to be
withdrawn

This document supersedes EN 50419:2006 and all of its amendments and corrigenda (if any).

EN 50419:2022 includes the following significant technical changes with respect to EN 50419:2006:

• The previous edition specified the marking requirements as described in 2002/96/EC (WEEE) and directly

refers to this Directive 2002/96/EC (WEEE) which was meanwhile replaced by 2012/19/EU (WEEE,

recast). This document presents the marking requirements independent from a regulation version.

• The revision clarifies the different possibilities of use the crossed-out wheeled bin combined with the black

bar and / or manufacturing date.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent

rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

This document has been prepared under a Standardization Request given to CENELEC by the European

Commission and the European Free Trade Association.

Any feedback and questions on this document should be directed to the users’ national standards

body/national committee. A complete listing of these bodies can be found on the CEN and CENELEC

websites.
---------------------- Page: 5 ----------------------
SIST EN 50419:2022
EN 50419:2022 (E)
Introduction

This document aims to assist the marking of electrical and electronic equipment (EEE) with a view to

minimizing the disposal of waste EEE (WEEE) as unsorted waste and to facilitating its separate collection. For

this purpose it specifies the different possibilities to use the crossed-out wheeled bin symbol combined with

the black bar and / or manufacturing date supporting the identification when the equipment was put on the

market.

This document supports the respective essential requirements of Directive 2012/19/EU (WEEE, recast). This

document does not constitute a request for design change for existing products specified to meet the previous

edition of the standard or the former Directive 2002/96/EC (WEEE).

This document supports the objectives of the Community's environment policy. These aim to preserve, protect

and improve the quality of the environment, protect human health and utilize natural resources prudently and

rationally.
---------------------- Page: 6 ----------------------
SIST EN 50419:2022
EN 50419:2022 (E)
1 Scope
This document specifies a marking

— of electrical and electronic equipment (EEE) with a view to minimizing the disposal of waste EEE (WEEE)

as unsorted waste and to facilitating its separate collection.

NOTE 1 This is in accordance with Article 14(4) of Directive 2012/19/EU (WEEE, recast)

— that serves to clearly identify the producer of the equipment and
— that the equipment has been put on the market after 13 August 2005.

NOTE 2 This is in accordance with Articles 12(3) and 15(2) of Directive 2012/19/EU (WEEE, recast)

— that applies to categories of electrical and electronic equipment subject to WEEE collection, treatment,

recovery and environmentally sound disposal as defined by European and national regulations, provided

the equipment concerned is not part of another type of equipment that does not fall within the scope of

above mentioned regulations.

NOTE 3 This is in accordance with Article 2 and Annexes I – IV of Directive 2012/19/EU (WEEE, recast) [1]

The definition
...

SLOVENSKI STANDARD
oSIST prEN 50419:2021
01-december-2021
Označevanje električne in elektronske opreme glede na ločeno zbiranje odpadkov
EEE (WEEE)

Marking of electrical and electronic equipment (EEE) in respect to separate collection of

waste EEE (WEEE)
Ta slovenski standard je istoveten z: prEN 50419:2021
ICS:
01.080.20 Grafični simboli za posebno Graphical symbols for use on
opremo specific equipment
13.030.30 Posebni odpadki Special wastes
29.020 Elektrotehnika na splošno Electrical engineering in
general
31.020 Elektronske komponente na Electronic components in
splošno general
oSIST prEN 50419:2021 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 50419:2021
---------------------- Page: 2 ----------------------
oSIST prEN 50419:2021
EUROPEAN STANDARD DRAFT
prEN 50419
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2021
ICS Will supersede EN 50419:2006 and all of its
amendments and corrigenda (if any)
English Version
Marking of electrical and electronic equipment (EEE) in respect
to separate collection of waste EEE (WEEE)

Marquage des équipements électriques et électroniques Kennzeichnung von Elektro- und Elektronikgeräten für eine

conformément à la collecte séparée des déchets EEE getrennte Sammlung von Elektro- und Elektronik-Altgeräten

(DEEE)
This draft European Standard is submitted to CENELEC members for enquiry.
Deadline for CENELEC: 2021-12-31.
It has been drawn up by CLC/TC 111X.

If this draft becomes a European Standard, CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which

stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CENELEC in three official versions (English, French, German).

A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to

the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,

Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the

Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,

Turkey and the United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to

provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and

shall not be referred to as a European Standard.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.

Project: 72209 Ref. No. prEN 50419:2021 E
---------------------- Page: 3 ----------------------
oSIST prEN 50419:2021
FprEN 50419:2021 (E)
Contents Page

European foreword ............................................................................................................................................. 3

Introduction ......................................................................................................................................................... 4

1 Scope ...................................................................................................................................................... 5

2 Normative references ............................................................................................................................ 5

3 Terms and definitions ........................................................................................................................... 5

4 Marking ................................................................................................................................................... 6

4.1 Requirements of marking of EEE ......................................................................................................... 6

4.1.1 Unique identification of the producer .................................................................................................. 6

4.1.2 Identification of date of put on the market for financial differentiation needs of WEEE ............... 6

4.1.3 Marking that the EEE is subject to separate WEEE collection ......................................................... 7

4.2 Design of the marking ........................................................................................................................... 7

4.2.1 Integrated marking ................................................................................................................................ 7

Figure 1 — Marking of electrical and electronic equipment as required by 4.1 b) 2) .................................. 8

4.2.2 Separate markings ................................................................................................................................. 9

Figure 2 — Crossed-out wheeled bin symbol .................................................................................................. 9

4.2.3 General marking design requirements ................................................................................................ 9

4.2.4 Location of the marking ........................................................................................................................ 9

Bibliography ...................................................................................................................................................... 10

---------------------- Page: 4 ----------------------
oSIST prEN 50419:2021
prEN 50419:2021 (E)
European foreword
This document (prEN 50419:2021) has been prepared by CLC/TC 111X “Environment”.
This document is currently submitted to the CENELEC Enquiry.
The following dates are proposed:
• latest date by which the existence of this (doa) dor + 6 months
document has to be announced at national
level
• latest date by which this document has to be (dop) dor + 12 months
implemented at national level by publication of
an identical national standard or by
endorsement
• latest date by which the national standards (dow) dor + 36 months (to
conflicting with this document have to be be confirmed or
withdrawn modified when voting)

This document will supersede EN 50419:2006 and all of its amendments and corrigenda (if any).

EN 50419:2021 includes the following significant technical changes with respect to EN 50419:2006:

• The previous edition specified the marking requirements as described in 2002/96/EC (WEEE) and directly

refers to this Directive. 2002/96/EC (WEEE) which was meanwhile replaced by 2012/19/EU (WEEE,

recast). This European Standard presents the marking requirements independent from a regulation

version.

• The revision clarifies the different possibilities of use the crossed-out wheeled bin combined with the black

bar and / or manufacturing date.

This document has been prepared under mandate M/336 given to CENELEC by the European Commission

and the European Free Trade Association, and supports the essential requirements of Directive 2012/19/EU.

---------------------- Page: 5 ----------------------
oSIST prEN 50419:2021
FprEN 50419:2021 (E)
Introduction

This document aims to assist the marking of electrical and electronic equipment (EEE) with a view to

minimizing the disposal of waste EEE (WEEE) as unsorted waste and to facilitating its separate collection. For

this purpose it specifies the different possibilities to use the crossed-out wheeled bin symbol combined with

the black bar and / or manufacturing date supporting the identification when the equipment was put on the

market.

This document supports the respective essential requirements of Directive 2012/19/EU (WEEE, recast). This

standard does not constitute a request for design change for existing products specified to meet the previous

edition of the standard or the former Directive 2002/96/EC (WEEE).

This document supports the objectives of the Community's environment policy. These aim to preserve, protect

and improve the quality of the environment, protect human health and utilize natural resources prudently and

rationally.
---------------------- Page: 6 ----------------------
oSIST prEN 50419:2021
prEN 50419:2021 (E)
1 Scope
This document specifies a marking

• of electrical and electronic equipment (EEE) with a view to minimizing the disposal of waste EEE (WEEE)

as unsorted waste and to facilitating its separate collection.

NOTE 1 This is in accordance with Article 14(4) of Directive 2012/19/EU (WEEE, recast);

• that serves to clearly identify the producer of the equipment and
• that the equipment has been put on the market after 13 August 2005.

NOTE 2 This is in accordance with Articles 12(3) and 15(2) of Directive 2012/19/EU (WEEE, recast);

• that applies to categories of electrical and electronic equipment subject to WEEE collection, treatment,

recovery and environmentally sound disposal as defined by European and national regulations, provided

the equipment concerned is not part of another type of equipment that does not fall within the

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.