SIST EN 14286:2008
(Main)Aluminium and aluminium alloys - Weldable rolled products for tanks for the storage and transportation of dangerous goods
Aluminium and aluminium alloys - Weldable rolled products for tanks for the storage and transportation of dangerous goods
This European standard specifies the technical conditions of inspection and delivery, the mechanical properties, the tolerances on dimensions and form of rolled semi-finished aluminium alloy products intended for tanks for the storage and transportation of dangerous goods, in particular of gasoline and other liquid hydrocarbons.
It applies to hot or cold-rolled strip, sheet and plate with a thickness from 3,0 mm and up to and including 12,0 mm used as a wall material.
Aluminium und Aluminiumlegierungen - Schweißbare Walzerzeugnisse für Tanks für Lagerung und Transport von Gefahrgut
Dieses Dokument legt die Technischen Lieferbedingungen, die mechanischen Eigenschaften, die Grenzabmaße
und Formtoleranzen für gewalztes Halbzeug aus Aluminiumlegierungen fest, das für die Herstellung
von Tanks zur Lagerung und zum Transport von Gefahrgut, speziell für Benzin und andere flüssige Kohlenwasserstoffe,
vorgesehen ist.
Es gilt für warm- oder kaltgewalzte Bänder, Bleche und Platten mit einer Dicke von 3,0 mm bis 12,0 mm, die
als Wandmaterial eingesetzt werden.
ANMERKUNG Die Übereinstimmung mit dem vorliegenden Dokument garantiert nicht die Übereinstimmung mit
nationalen oder internationalen Vorschriften. Der Anwender dieses Dokuments ist für die Überprüfung verantwortlich, dass
das Erzeugnis, das er bestellt oder verkauft, mit allen zutreffenden Vorschriften übereinstimmt. Abhängig von den
chemischen und physikalischen Eigenschaften des Gefahrgutes, das transportiert oder gelagert werden soll, kann es
notwendig sein, zusätzliche Eigenschaften oder Technische Lieferbedingungen zu vereinbaren, damit sie mit den
geltenden Vorschriften übereinstimmen.
Aluminium et alliages d'aluminium - Produits laminés soudables pour réservoirs de stockage et de transport des matières dangereuses
Le présent document spécifie les conditions techniques de contrôle et de livraison, les caractéristiques
mécaniques, les tolérances de dimension et de forme des produits semi-finis laminés en alliages d’aluminium
pour réservoirs de stockage et de transport de matières dangereuses, en particulier l’essence et autres
hydrocarbures liquides.
Il s’applique aux tôles minces, bandes et tôles épaisses laminées à froid ou à chaud, d’une épaisseur
comprise entre 3,0 mm et 12,0 mm inclus, utilisées comme matériau d’enveloppe.
NOTE La conformité au présent document ne confère pas conformité aux réglementations nationales ou
internationales. L’utilisateur du document est responsable de vérifier que le matériau qu’il commande ou vend est
conforme à toutes les réglementations applicables. Suivant les caractéristiques chimiques et physiques de la matière
dangereuse à transporter ou à stocker, il peut être nécessaire de se mettre d’accord sur des caractéristiques ou des
conditions de contrôle supplémentaires pour vérifier la conformité à la réglementation.
Aluminij in aluminijeve zlitine - Varivi valjani izdelki za rezervoarje za shranjevanje in prevažanje nevarnih snovi
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aluminij in aluminijeve zlitine - Varivi valjani izdelki za rezervoarje za shranjevanje in prevažanje nevarnih snoviAluminium und Aluminiumlegierungen - Schweißbare Walzerzeugnisse für Tanks für Lagerung und Transport von GefahrgutAluminium et alliages d'aluminium - Produits laminés soudables pour réservoirs de stockage et de transport des matières dangereusesAluminium and aluminium alloys - Weldable rolled products for tanks for the storage and transportation of dangerous goods77.150.10Aluminijski izdelkiAluminium products23.020.10UH]HUYRDUMLStationary containers and tanks13.300Varstvo pred nevarnimi izdelkiProtection against dangerous goodsICS:Ta slovenski standard je istoveten z:EN 14286:2008SIST EN 14286:2008en,fr,de01-november-2008SIST EN 14286:2008SLOVENSKI
STANDARDSIST EN 14286:20071DGRPHãþD
SIST EN 14286:2008
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14286September 2008ICS 77.150.10Supersedes EN 14286:2007
English VersionAluminium and aluminium alloys - Weldable rolled products fortanks for the storage and transportation of dangerous goodsAluminium et alliages d'aluminium - Produits laminéssoudables pour réservoirs de stockage et de transport desmatières dangereusesAluminium und Aluminiumlegierungen - SchweißbareWalzerzeugnisse für Tanks für Lagerung und Transport vonGefahrgutThis European Standard was approved by CEN on 8 August 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14286:2008: ESIST EN 14286:2008
EN 14286:2008 (E) 2 Contents Page Foreword.3 Introduction.4 1 Scope.5 2 Normative references.5 3 Terms and definitions.6 4 Selection of materials.6 5 Designation of the products.6 6 Ordering information.6 7 Requirements.7 7.1 General.7 7.2 Technical conditions for inspection and delivery.7 7.3 Mechanical properties.7 7.4 Surface conditions.8 7.5 Tolerances on dimensions and form.9 8 Inspection.9 8.1 Inspections to be carried out.9 8.2 Type and content of inspection documents.10 9 Quality assurance.10 10 Marking.10 Annex A (informative)
Explanation of temper designations used in Table 1 based on definitions of EN 515.11 Bibliography.12
SIST EN 14286:2008
EN 14286:2008 (E) 3 Foreword This document (EN 14286:2008) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2009, and conflicting national standards shall be withdrawn at the latest by March 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 14286:2007. Within its programme of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 7 "Sheets, strips and plates" to revise EN 14286:2007. The following technical changes have been made: Table 1: change of the elongation and the bending radius at 180° values for alloy EN AW-5059 temper H112; Table 1: change of the elongation value for alloy EN AW-5186 temper O/H111; Table 1: name of Rm (tensile strength), Rp0,2
(yield strength) and A (elongation after fracture) have been completed. CEN/TC 132 affirms it is policy that in the case when a patentee refuses to grant licenses on standardised standard products under reasonable and not discriminatory condition, then this product shall be removed from the corresponding document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
SIST EN 14286:2008
EN 14286:2008 (E) 4 Introduction It is essential that aluminium alloy semi-finished rolled products intended for the construction of tanks for the storage and transportation of dangerous goods satisfy a certain number of specific technical conditions for inspection and delivery as well as specific mechanical and other properties which distinguish them from similar semi-finished products for general applications. SIST EN 14286:2008
EN 14286:2008 (E) 5 1 Scope This document specifies the technical conditions of inspection and delivery, the mechanical properties, the tolerances on dimensions and form of rolled semi-finished aluminium alloy products intended for tanks for the storage and transportation of dangerous goods, in particular of gasoline and other liquid hydrocarbons. It applies to hot or cold-rolled strip, sheet and plate with a thickness from 3,0 mm and up to and including 12,0 mm used as a wall material. NOTE Compliance with the present document does not ensure compliance with national or international regulations. The user of the document is responsible for checking that the material he orders or sells complies with all applicable regulations. Depending on the chemical and physical properties of the dangerous good to be transported or stored, it can be necessary to agree on additional properties or inspection conditions in order to comply with applying regulations. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 485-1, Aluminium and aluminium alloys — Sheet, strip and plate — Part 1: Technical conditions for inspection and delivery EN 485-3, Aluminium and aluminium alloys — Sheet, strip and plate — Part 3: Tolerances on dimensions and form for hot-rolled products EN 485-4, Aluminium and aluminium alloys — Sheet, strip and plate — Part 4: Tolerances on shape and dimensions for cold-rolled products EN 515, Aluminium and aluminium alloys — Wrought products — Temper designations EN 573-3, Aluminium and aluminium alloys — Chemical composition and form of wrought products — Part 3: Chemical composition and form of products EN 10002-1, Metallic materials — Tensile testing — Part 1: Method of test at ambient temperature EN 10204, Metallic products — Types of inspection documents EN 12258-1:1998, Aluminium and aluminium alloys — Terms and definitions — Part 1: General terms EN ISO 7438, Metallic materials — Bend test (ISO 7438:2005) ASTM G66, Standard Test Method for Visual Assessment of Exfoliation Corrosion Susceptibility of 5XXX Series Aluminium Alloys (ASSET Test) ASTM G67, Standard Test Method for Determining the Susceptibility to Intergranular Corrosion of 5XXX Series Aluminium Alloys by Mass Loss After Exposure to Nitric Acid (NAMLT Test) ASTM B928/B928M, Standard Specification for High Magnesium Aluminium-Alloy Sheet and Plate for Marine Service and Similar Environments SIST EN 14286:2008
EN 14286:2008 (E) 6 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 12258-1:1998 and the following apply. 3.1 capability clause clause whose reference signifies that sufficient evidence of a statistical nature with respect to the properties under consideration can be submitted by the manufacturer to demons
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.