EN ISO 10855-1:2018

Offshore containers and associated lifting sets - Part 1: Design, manufacture and marking of offshore containers (ISO 10855-1:2018)

This document specifies requirements for the design, manufacture and marking of offshore containers with a maximum gross mass not exceeding 25 000 kg, intended for repeated use to, from and between offshore installations and ships.
This document specifies only transport-related requirements.

Offshore-Container und dazugehörige Anschlaggarnituren - Teil 1: Auslegung, Herstellung und Kennzeichnung (ISO 10855-1:2018)

Containers offshore et dispositifs de levage associés - Partie 1: Conception, fabrication et marquage des containers offshore (ISO 10855-1:2018)

Le présent document spécifie les exigences relatives à la conception, à la fabrication et au marquage des conteneurs offshore ayant une masse brute maximale inférieure ou égale à 25 000 kg, destinés à un usage répété à destination, en provenance ou entre des installations en mer et des navires.
Le présent document spécifie uniquement les exigences liées au transport.

Plavajoče kontejnerske enote in z njimi povezan dvižni pribor - 1. del: Načrtovanje, izdelava in označevanje plavajočih kontejnerskih enot (ISO 10855-1:2018)

Ta dokument določa zahteve za načrtovanje, izdelavo in označevanje plavajočih kontejnerskih enot z največjo bruto maso, ki ne presega 25 000 kg, ki so namenjene za večkratni prenos na plavajoče enote in ladje, z njih ter med njimi.
Ta dokument določa samo s transportom povezane zahteve.

General Information

• Status: Published
• Publication Date: 10-Jul-2018
• Withdrawal Date: 30-Jan-2019
• ICS: 55.180.10 - General purpose containers
• ICS: 75.180.10 - Exploratory, drilling and extraction equipment
• Technical Committee: CEN/TC 12 - Materials, equipment and offshore structures for petroleum and natural gas industries
• Drafting Committee: CEN/TC 12 - Materials, equipment and offshore structures for petroleum and natural gas industries
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 11-Jul-2018
• Completion Date: 11-Jul-2018
• Ref Project: SIST EN ISO 10855-1:2018 - Offshore containers and associated lifting sets - Part 1: Design, manufacture and marking of offshore containers (ISO 10855-1:2018)

Relations

• Replaces: EN 12079-1:2006 - Offshore containers and associated lifting sets - Part 1: Offshore container - Design, manufacture and marking
• Effective Date: 20-Jul-2016
• Revised: prEN ISO 10855-1 - Offshore containers and associated lifting sets - Part 1: Design, manufacture and marking of offshore containers (ISO/DIS 10855-1:2024)
• Effective Date: 04-May-2022

Standards Content (Sample)

SLOVENSKI STANDARD
01-oktober-2018
1DGRPHãþD
SIST EN 12079-1:2007
3ODYDMRþHNRQWHMQHUVNHHQRWHLQ]QMLPLSRYH]DQGYLåQLSULERUGHO1DþUWRYDQMH
L]GHODYDLQR]QDþHYDQMHSODYDMRþLKNRQWHMQHUVNLKHQRW,62
Offshore containers and associated lifting sets - Part 1: Design, manufacture and
marking of offshore containers (ISO 10855-1:2018)
Offshore container - Teil 1: Auslegung, Herstellung und Kennzeichnung (ISO 10855-
1:2018)
Containers offshore - Partie 1: Conception, fabrication et marquage (ISO 10855-1:2018)
Ta slovenski standard je istoveten z: EN ISO 10855-1:2018
ICS:
55.180.10 9HþQDPHQVNLNRQWHMQHUML General purpose containers
75.180.10 Oprema za raziskovanje, Exploratory, drilling and
vrtanje in odkopavanje extraction equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 10855-1
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2018
EUROPÄISCHE NORM
ICS 75.180.10 Supersedes EN 12079-1:2006
English Version
Offshore containers and associated lifting sets - Part 1:
Design, manufacture and marking of offshore containers
(ISO 10855-1:2018)
Containers offshore et dispositifs de levage associés - Offshore-Container und dazugehörige
Partie 1: Conception, fabrication et marquage des Anschlaggarnituren - Teil 1: Auslegung, Herstellung
containers offshore (ISO 10855-1:2018) und Kennzeichnung (ISO 10855-1:2018)
This European Standard was approved by CEN on 30 April 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10855-1:2018 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 10855-1:2018) has been prepared by Technical Committee ISO/TC 67
"Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries"
in collaboration with Technical Committee CEN/TC 12 “Materials, equipment and offshore structures
for petroleum, petrochemical and natural gas industries” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2019, and conflicting national standards shall
be withdrawn at the latest by January 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 12079-1:2006.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 10855-1:2018 has been approved by CEN as EN ISO 10855-1:2018 without any
modification.
INTERNATIONAL ISO
STANDARD 10855-1
First edition
2018-05
Offshore containers and associated
lifting sets —
Part 1:
Design, manufacture and marking of
offshore containers
Containers offshore et dispositifs de levage associés —
Partie 1: Conception, fabrication et marquage des containers offshore
Reference number
ISO 10855-1:2018(E)
©
ISO 2018
ISO 10855-1:2018(E)
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

ISO 10855-1:2018(E)
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 3
4 Symbols . 5
5 Design . 5
5.1 General . 5
5.2 Structural strength . 6
5.2.1 General. 6
5.2.2 Lifting loads . 7
5.2.3 Impact loads . . . 8
5.2.4 Internal forces on container walls . 9
5.2.5 Minimum material thickness . 9
5.3 Welding . 9
5.4 Additional design details . 9
5.4.1 Floor . . 9
5.4.2 Doors and hatches .10
5.4.3 Intermediate cargo decks .10
5.4.4 Driving ramps .10
5.4.5 Internal lashing points .10
5.4.6 Fork lift pockets .10
5.4.7 Top protection .11
5.4.8 Pad eyes .11
5.4.9 ISO-corner fittings .12
5.4.10 Equipment .12
5.4.11 Coating and corrosion protection .12
5.5 Tank containers .13
5.5.1 General.13
5.5.2 Frame .13
5.5.3 Tanks for fluids .13
5.5.4 Impact protection on tank containers for dangerous cargoes .13
5.6 Containers for bulk solids.13
6 Materials .14
6.1 Steel — General .14
6.2 Rolled and extruded steels in offshore container structures .15
6.2.1 General requirements .15
6.2.2 Groups of steels .15
6.2.3 Stainless steel .15
6.2.4 Steel forgings .15
6.2.5 Steel castings in ISO-corner fittings .16
6.3 Aluminium .16
6.4 Non-metallic materials .17
6.5 Material documents .
...