IEC 62059-32-1:2011

Electricity metering equipment - Dependability - Part 32-1: Durability - Testing of the stability of metrological characteristics by applying elevated temperature

IEC 62059-32-1:2011 specifies a method for testing the stability of metrological characteristics of electricity meters, by operating a test specimen at the upper limit of the specified operating range of temperature, voltage and current for an extended period.

Appareils de comptage d'électricité - Sûreté de fonctionnement - Partie 32-1: Durabilité - Contrôle de stabilité des caractéristiques métrologiques en appliquant une température élevée

La CEI 62059-32-1:2011 spécifie une méthode pour les essais de stabilité des caractéristiques métrologiques des compteurs d'électricité, en faisant fonctionner un exemplaire d'essai à la limite supérieure de la température, de la tension et du courant dans le domaine de fonctionnement spécifié, pendant une durée prolongée.

General Information

• Status: Published
• Publication Date: 06-Dec-2011
• ICS: 17.220.20 - Measurement of electrical and magnetic quantities
• ICS: 19.020 - Test conditions and procedures in general
• ICS: 91.140.50 - Electricity supply systems
• Technical Committee: TC 13 - Electrical energy measurement and control
• Drafting Committee: WG 13 - TC 13/WG 13
• Current Stage: PPUB - Publication issued
• Start Date: 31-Dec-2011
• Completion Date: 07-Dec-2011

Standards Content (Sample)

IEC 62059-32-1 ®
Edition 1.0 2011-12
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Electricity metering equipment – Dependability –
Part 32-1: Durability – Testing of the stability of metrological characteristics by
applying elevated temperature
Appareils de comptage de l'électricité – Sûreté de fonctionnement –
Partie 32-1: Durabilité – Contrôle de stabilité des caractéristiques métrologiques
en appliquant une température élevée

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or
IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.

IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: [e-mail]
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
 Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
 IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
 Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
 Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: [e-mail]
Tel.: [phone]
Fax: [phone]
A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.

A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
 Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm
Le Catalogue en-ligne de la CEI vous permet d’effectuer des recherches en utilisant différents critères (numéro de référence,
texte, comité d’études,…). Il donne aussi des informations sur les projets et les publications retirées ou remplacées.
 Just Published CEI: www.iec.ch/online_news/justpub
Restez informé sur les nouvelles publications de la CEI. Just Published détaille deux fois par mois les nouvelles
publications parues. Disponible en-ligne et aussi par email.
 Electropedia: www.electropedia.org
Le premier dictionnaire en ligne au monde de termes électroniques et électriques. Il contient plus de 20 000 termes et
définitions en anglais et en français, ainsi que les termes équivalents dans les langues additionnelles. Egalement appelé
Vocabulaire Electrotechnique International en ligne.
 Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm
Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du
Service clients ou contactez-nous:
Email: [e-mail]
Tél.: [phone]
Fax: [phone]
IEC 62059-32-1 ®
Edition 1.0 2011-12
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Electricity metering equipment – Dependability –
Part 32-1: Durability – Testing of the stability of metrological characteristics by
applying elevated temperature
Appareils de comptage de l'électricité – Sûreté de fonctionnement –
Partie 32-1: Durabilité – Contrôle de stabilité des caractéristiques métrologiques
en appliquant une température élevée

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX N
ICS 17.220; 19.020; 91.140.50 ISBN 978-2-88912-827-3

– 2 – 62059-32-1  IEC:2011
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 General . 7
5 Initial measurements . 7
6 Conditioning . 7
7 Intermediate measurements – verification of energy measurement and registration . 9
7.1 General . 9
7.2 Method A: Test method using a reference meter. 9
7.2.1 Test conditions . 9
7.2.2 Test using a reference standard meter . 10
7.2.3 Test using a reference meter of the same type as the MUT . 10
7.3 Method B: Test method using a stable load . 11
7.4 Final temperature ramp . 12
8 Recovery . 12
9 Final measurements and acceptance criteria . 12
10 Information to be given in the test report . 13
Bibliography . 14

Table 1 – Limits of change in percentage error at I . 13
max
62059-32-1  IEC:2011 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ELECTRICITY METERING EQUIPMENT –
DEPENDABILITY –
Part 32-1: Durability –
Testing of the stability of metrological characteristics
by applying elevated temperature

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62059-32-1 has been prepared by IEC technical committee 13:
Electrical energy measurement, tariff- and load control.
The text of this standard is based on the following documents:
FDIS RVD
13/1483/FDIS 13/1493/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

– 4 – 62059-32-1  IEC:2011
A list of all parts of IEC 62059 series, under the general title Electricity metering equipment –
Dependability, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
62059-32-1  IEC:2011 – 5 –
INTRODUCTION
Electricity meters are products designed for high reliability and durability to operate
continuously for extended periods without supervision.
To manage metering assets effectively, it is important to have tools for predicting and
estimating life characteristics of various types.
IEC 62059-41 provides methods for predicting the failure rate – assumed to be constant – of
metering equipment, based on the parts stress method.
IEC 62059-31-1 provides a method for estimating life characteristics using accelerated
reliability testing by operating the test specimens at elevated temperature and humidity.
Future parts of IEC 62059-31 may be established to cover accelerated reliability testing,
applying other stresses.
This standard, IEC 62059-32-1 provides a test method to evaluate one important aspect of
durability, the stability of metrology characteristics, by operating a test specimen at the upper
limit of the specified operating range of temperature, voltage and current for an extended
period. Future parts of IEC 62059-32 may be established to cover other kinds of stress or
other aspects of durability.
– 6 – 62059-32-1  IEC:2011
ELECTRICITY METERING EQUIPMENT –
DEPENDABILITY –
Part 32-1: Durability –
Testing of the stability of metrological characteristics
by applying elevated temperature

1 Scope
The stability of metrological characteristics is one important aspect of durability.
This part of IEC 62059 specifies a method for testing the stability of metrological
characteristics of electricity meters, by operating a test specimen at the upper limit of the
specified operating range of temperature, voltage and current for an extended period.
Functional performance other than the accuracy of energy
...