SIST EN ISO 13766-1:2018
(Main)Earth-moving and building construction machinery - Electromagnetic compatibility (EMC) of machines with internal electrical power supply - Part 1: General EMC requirements under typical electromagnetic environmental conditions (ISO 13766-1:2018)
Earth-moving and building construction machinery - Electromagnetic compatibility (EMC) of machines with internal electrical power supply - Part 1: General EMC requirements under typical electromagnetic environmental conditions (ISO 13766-1:2018)
This International Standard provides test methods and acceptance criteria for the evaluation of the electromagnetic compatibility of construction machinery as defined in ISO 6165 for earth-moving machinery and ISO 8811 for road-construction machines.
It deals with General EMC requirements under typical EMC environmental conditions.
Functional safety requirements are covered in part 2 of ISO 13766.
Electrical and/or electronic component(s) or separate technical unit(s) intended to be fitted in construction machinery are also dealt with in this International Standard. The following electromagnetic disturbance phenomena are evaluated:
- broadband and narrowband electromagnetic interference;
- electromagnetic field immunity test;
- broadband and narrowband interference of electrical/electronic sub-assemblies;
- electromagnetic field immunity test of electrical/electronic sub-assemblies;
- electrostatic discharge;
- conducted transients.
Construction machinery can have DC and/or AC internal electrical power supply systems.
Machines that are designed to be supplied by the „Public Mains Network“ are specifically excluded.
Baumaschinen - Elektromagnetische Verträglichkeit von Maschinen mit internem elektrischen Bordnetz - Teil 1: Allgemeine EMV-Anforderungen unter typischen EMV-Umgebungsbedingungen (ISO 13766-1:2018)
Engins de terrassement et machines pour la construction des bâtiments - Compatibilité électromagnétique (CEM) des machines équipées de réseaux électriques de distribution interne - Partie 1: Exigences CEM générales dans des conditions électromagnétiques environnementales typiques (ISO 13766-1:2018)
L'ISO 13766-1:2018 spécifie des méthodes d'essai et des critères d'acceptation pour l'évaluation de la compatibilité électromagnétique (CEM) des engins de terrassement, tels que définis dans l'ISO 6165:2012, et des machines pour la construction des bâtiments suivantes, telles que classées dans l'ISO/TR 12603:2010:
- machines de forage et de fondation;
- équipement utilisé pour la préparation, le transport et le serrage du béton, du mortier et des armatures;
- machines et équipement de construction et d'entretien des routes.
L'ISO 13766-1:2018 traite des exigences CEM générales dans des conditions environnementales électromagnétiques typiques. (L'ISO 13766‑2:2018 traite des exigences CEM spécifiquement liées à la sécurité fonctionnelle).
Les sous-ensembles électriques/électroniques (S.E.E.) et S.E.E. séparés destinés à être installés sur les machines sont également traités. Les phénomènes de perturbations électromagnétiques suivants sont évalués:
- interférence électromagnétique à large bande et à bande étroite;
- immunité au champ électromagnétique;
- décharge électrostatique;
- transitoires conduits.
Les machines peuvent être équipées de systèmes d'alimentation électrique internes CC ou CA ou une combinaison des deux.
L'ISO 13766-1:2018 n'est pas applicable aux machines conçues pour être alimentées par un réseau externe ni aux phénomènes provoqués par des applications militaires.
NOTE 1 Les machines connectées au réseau sont couvertes par l'IEC 61000.
NOTE 2 Les machines hybrides sont couvertes par le règlement R10-Rév. 5 de la CEE-ONU.
Stroji za zemeljska dela in graditev objektov - Elektromagnetna združljivost (EMC) strojev z lastnim električnim napajanjem - 1. del: Splošne zahteve glede EMC v tipičnih pogojih elektromagnetnega okolja (ISO 13766-1:2018)
Ta mednarodni standard določa preskusne metode in kriterije sprejemljivosti za vrednotenje elektromagnetne združljivosti gradbenih strojev, kot so opredeljeni v standardu ISO 6165 za stroje za zemeljska dela in v standardu ISO 8811 za stroje za gradnjo cest.
Obravnava splošne zahteve glede EMC v tipičnih pogojih elektromagnetnega okolja.
Funkcionalne varnostne zahteve so obravnavane v 2. delu standarda ISO 13766.
Električne in/ali elektronske komponente ali ločene tehnične enote, namenjene za pritrditev na gradbene stroje, so prav tako obravnavane v tem mednarodnem standardu. Ocenjeni so naslednji elektromagnetni pojavi oziroma motnje:
– širokopasovne in ozkopasovne elektromagnetne motnje;
– preskus odpornosti elektromagnetnega polja;
– širokopasovne in ozkopasovne motnje električnih/elektronskih podsklopov;
– preskus odpornosti elektromagnetnega polja električnih/elektronskih podsklopov;
– elektrostatične razelektritve;
– prehodne elektromagnetne motnje.
Gradbeni stroji imajo lahko lastne enosmerne (DC) in/ali enofazne (AC) električne napajalne sisteme.
Stroji, ki so zasnovani za napajanje iz »javnega omrežja«, so izrecno izključeni.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 13766-1:2018
01-september-2018
1DGRPHãþD
SIST EN 13309:2010
6WURML]D]HPHOMVNDGHODLQJUDGLWHYREMHNWRY(OHNWURPDJQHWQD]GUXåOMLYRVW (0&
VWURMHY]ODVWQLPHOHNWULþQLPQDSDMDQMHPGHO 6SORãQH]DKWHYHJOHGH(0&Y
WLSLþQLKSRJRMLKHOHNWURPDJQHWQHJDRNROMD ,62
Earth-moving and building construction machinery - Electromagnetic compatibility (EMC)
of machines with internal electrical power supply - Part 1: General EMC requirements
under typical electromagnetic environmental conditions (ISO 13766-1:2018)
Baumaschinen - Elektromagnetische Verträglichkeit von Maschinen mit internem
elektrischen Bordnetz - Teil 1: Allgemeine EMV-Anforderungen unter typischen EMV-
Umgebungsbedingungen (ISO 13766-1:2018)
Engins de terrassement et machines pour la construction des bâtiments - Compatibilité
électromagnétique (CEM) des machines équipées de réseaux électriques de distribution
interne - Partie 1: Exigences CEM générales dans des conditions électromagnétiques
environnementales typiques (ISO 13766-1:2018)
Ta slovenski standard je istoveten z: EN ISO 13766-1:2018
ICS:
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
53.100 Stroji za zemeljska dela Earth-moving machinery
SIST EN ISO 13766-1:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 13766-1:2018
---------------------- Page: 2 ----------------------
SIST EN ISO 13766-1:2018
EN ISO 13766-1
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2018
EUROPÄISCHE NORM
ICS 33.100.01; 53.100 Supersedes EN 13309:2010
English Version
Earth-moving and building construction machinery -
Electromagnetic compatibility (EMC) of machines with
internal electrical power supply - Part 1: General EMC
requirements under typical electromagnetic
environmental conditions (ISO 13766-1:2018)
Engins de terrassement et machines pour la Baumaschinen - Elektromagnetische Verträglichkeit
construction des bâtiments - Compatibilité von Maschinen mit internem elektrischen Bordnetz -
électromagnétique (CEM) des machines équipées de Teil 1: Allgemeine EMV-Anforderungen unter
réseaux électriques de distribution interne - Partie 1: typischen EMV-Umgebungsbedingungen (ISO 13766-
Exigences CEM générales dans des conditions 1:2018)
électromagnétiques environnementales typiques (ISO
13766-1:2018)
This European Standard was approved by CEN on 8 May 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13766-1:2018 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 13766-1:2018
EN ISO 13766-1:2018 (E)
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2014/30/EU aimed to be covered . 4
2
---------------------- Page: 4 ----------------------
SIST EN ISO 13766-1:2018
EN ISO 13766-1:2018 (E)
European foreword
This document (EN ISO 13766-1:2018) has been prepared by Technical Committee ISO/TC 127 "Earth-
moving machinery" in collaboration with Technical Committee CEN/TC 151 “Construction equipment
and building material machines - Safety” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2018, and conflicting national standards
shall be withdrawn at the latest by December 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13309:2010.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 13766-1:2018 has been approved by CEN as EN ISO 13766-1:2018 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 13766-1:2018
EN ISO 13766-1:2018 (E)
Annex ZA
(informative)
Relationship between this European standard and the essential requirements of
Directive 2014/30/EU [2014 OJ L96] aimed to be covered
This European standard has been prepared under the European Commission standardisation request
1
C(2016) 7641 final of 30.11.2016 , ('M/552'), as regards harmonised standards in support of Directive
2014/30/EU relating to electromagnetic compatibility, to provide one voluntary means of conforming to
essential requirements of Directive 2014/30/EU of the European Parliament and of the Council of 26 February
2014 on the harmonisation of the laws of the Member States relating to electromagnetic compatibility [2014
OJ L96].
Once this standard is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of this standard given in Table ZA.1 confers, within the limits of the scope of this
standard, a presumption of conformity with the corresponding essential requirements of that Directive, and
associated EFTA regulations.
Table ZA.1 – Correspondence between this European standard and the Essential
Requirements set out in Directive 2014/30/EU [2014 OJ L96]
Essential requirements of Clause(s) / sub-clause(s)
Remarks / Notes
Directive 2014/30/EU of this EN
Annex I. 1(a) (electromagnetic 4 Requirements.
disturbances)
Particularly, 4.2, 4.3, 4.5, 4.6
Annex I. 1(b) (electromagnetic 4 Requirements.
immunity)
Particularly, 4.4, 4.7, 4.8, 4.9
WARNING 1: Presumption of conformity stays valid only as long as a reference to this European standard is
maintained in the list published in the Official Journal of the European Union. Users of this standard should
consult frequently the latest list published in the Official Journal of the European Union.
WARNING 2: Other Union legislation may be applicable to the product(s) falling within the scope of this
standard.
1
COMMISSION IMPLEMENTING DECISION C(2016) 7641 final of 30.11.2016 on a standardisation request to the European
Committee for Standardisation, to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards harmonised standards in support of Directive 2014/30/EU of the European
Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to
electromagnetic compatibility.
4
---------------------- Page: 6 ----------------------
SIST EN ISO 13766-1:2018
INTERNATIONAL ISO
STANDARD 13766-1
First edition
2018-04
Earth-moving and building
construction machinery —
Electromagnetic compatibility (EMC)
of machines with internal electrical
power supply —
Part 1:
General EMC requirements
under typical electromagnetic
environmental conditions
Engins de terrassement et machines pour la construction des
bâtiments — Compatibilité électromagnétique (CEM) des machines
équipées de réseaux électriques de distribution interne —
Partie 1: Exigences CEM générales dans des conditions
électromagnétiques environnementales typiques
Reference number
ISO 13766-1:2018(E)
©
ISO 2018
---------------------- Page: 7 ----------------------
SIST EN ISO 13766-1:2018
ISO 13766-1:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 13766-1:2018
ISO 13766-1:2018(E)
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Requirements . 6
4.1 General requirements . 6
4.1.1 Fulfilment of requirements . 6
4.1.2 Test specimen . 6
4.1.3 Additional requirements for immunity tests. 7
4.2 Specifications for broadband electromagnetic emission radiated from machinery . 7
4.2.1 Method of measurement . 7
4.2.2 Broadband reference limits . 7
4.3 Specifications concerning narrowband electromagnetic emission radiated from
machinery. 7
4.3.1 Method of measurement . 7
4.3.2 Narrowband reference limits . 7
4.4 Specifications concerning the immunity of machinery to electromagnetic radiation . 8
4.4.1 Test method . 8
4.4.2 Machinery immunity reference limits . 8
4.5 Specifications concerning broadband electromagnetic emissions radiated from ESA . 9
4.5.1 Method of measurement . 9
4.5.2 ESA broadband reference limits . 9
4.6 Specifications concerning narrowband electromagnetic emissions radiated from ESA . 9
4.6.1 Method of measurement . 9
4.6.2 ESA narrowband reference limits . 9
4.7 Specifications concerning the immunity of ESA to electromagnetic radiation . 9
4.7.1 Method of testing . 9
4.7.2 ESA immunity reference limits .10
4.8 Electrostatic discharge (ESD) .10
4.8.1 Method of testing .10
4.8.2 Reference limits .10
4.9 Conducted transients .11
4.9.1 General.11
4.9.2 Method of testing .11
4.9.3 Conducted emission — Reference limits .11
4.9.4 Conducted immunity — Reference limits and functional status.11
5 Exceptions .13
6 Test report .14
Annex A (normative) Reference limits .15
Annex B (normative) Method of measurement of radiated broadband electromagnetic
emissions from machinery — Complete machine only .21
Annex C (normative) Method of measurement of radiated narrowband electromagnetic
emissions from machinery — Complete machine only .26
Annex D (normative) Method of measurement of radiated broadband electromagnetic
emissions from electrical/electronic sub-assemblies (ESA) .30
Annex E (normative) Method of measurement of radiated narrowband electromagnetic
emissions from ESA .36
© ISO 2018 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 13766-1:2018
ISO 13766-1:2018(E)
Annex F (informative) Guidance for selecting test specimen configuration and additional
considerations .39
Bibliography .40
iv © ISO 2018 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 13766-1:2018
ISO 13766-1:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/iso/foreword .html.
The committee responsible for this document is ISO/TC 127, Earth-moving machinery, Subcommittee
SC 2, Safety, ergonomics and general requirements.
This first edition of ISO 13766-1:2018, together with ISO 13766-2:2018, cancels and replaces
ISO 13766:2006, of which it constitutes a technical revision and contains the following changes:
— the scope has been extended to specify building construction machinery as well as earth-moving
machinery;
— the provisions have been brought up to date with technological change;
— normative references have been updated to the latest editions;
A list of all parts in the ISO 13766 series can be found on the ISO website.
© ISO 2018 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 13766-1:2018
ISO 13766-1:2018(E)
Introduction
This document is a type-C standard as stated in ISO 12100:2010.
This document is of relevance, in particular, for the following stakeholder groups representing the
market players with regard to machinery safety:
— machine manufacturers (small, medium and large enterprises);
— health and safety bodies (regulators, accident prevention organisations, market surveillance etc.)
Others can be affected by the level of machinery safety achieved with the means of the document by the
above-mentioned stakeholder groups:
— machine users/employers (small, medium and large enterprises);
— machine users/employees (e.g. trade unions, organizations for people with special needs);
— service providers, e.g. for maintenance (small, medium and large enterprises);
— consumers (in case of machinery intended for use by consumers).
The above-mentioned stakeholder groups have been given the possibility to participate at the drafting
process of this document.
The machinery concerned and the extent to which hazards, hazardous situations or hazardous events
are covered are indicated in the Scope of this document.
When requirements of this type-C standard are different from those which are stated in type-A or
type-B standards, the requirements of this type-C standard take precedence over the requirements of
the other standards for machines that have been designed and built according to the requirements of
this type-C standard.
With the increasing use of electronic devices in areas where earth-moving and machinery operates, there
is a need to ensure that the machinery is provided with adequate immunity to external electromagnetic
fields. As more machinery is fitted with electrical and electronic devices, it is necessary to ensure that
the emissions of electromagnetic fields from the machinery meet acceptable limits.
Electrical and high frequency disturbances emerge during the normal operation of many parts of
machine devices and systems. They are generated within a large frequency range with different
electrical characteristics and by conduction or radiation, which can be imparted to other electrical/
electronic devices and systems by conduction or radiation. Narrowband signals generated by sources
of interference inside or outside the machinery can also be coupled into electrical/electronic systems
whereby they can influence the normal function of electrical/electronic devices.
Electrostatic discharges are relevant to the machinery because control elements can be positioned
outside the operator station where potential differences could emerge at contact points. Conducted
transients in power supply wiring must be considered because the machinery can contain open systems,
in which several devices or components can be combined to complement machine functionality.
While there are many existing standards for a variety of products and systems, the test method
presented by ISO 13766:2018 provides for the specific test conditions of the machinery within its scope
as well as the electrical/electronic sub-assemblies (ESA) or ESA separate from the machinery. The test
method recognizes that due to their size and usage, the arrangement of the machines in the test facility
needs to be representative of their typical operating characteristics. This document provides test
methods and criteria which are acceptable for the machine types it covers, considering their unique
characteristics and operating parameters.
Because the machinery has a number of systems that consist of components that can be used on a
variety of machine types, the approach of defining ESA or separate ESAs for these components is
applied for the immunity and emissions test methods. This allows these components to be evaluated by
vi © ISO 2018 – All rights reserved
---------------------- Page: 12 ----------------------
SIST EN ISO 13766-1:2018
ISO 13766-1:2018(E)
the test method in existing laboratory facilities consisting of specially equipped shielded rooms. When
electrical/electronic sub-assembly tests are conducted, it is necessary to consider any additional effects
imparted by wiring systems used to connect the sub-assemblies into the machinery. The tests can also
be conducted on the machinery.
© ISO 2018 – All rights reserved vii
---------------------- Page: 13 ----------------------
SIST EN ISO 13766-1:2018
---------------------- Page: 14 ----------------------
SIST EN ISO 13766-1:2018
INTERNATIONAL STANDARD ISO 13766-1:2018(E)
Earth-moving and building construction machinery —
Electromagnetic compatibility (EMC) of machines with
internal electrical power supply —
Part 1:
General EMC requirements under typical electromagnetic
environmental conditions
1 Scope
This document provides test methods and acceptance criteria for the evaluation of the electromagnetic
compatibility (EMC) of earth-moving machinery, as defined in ISO 6165:2012, and of the following
building construction machinery as defined in ISO/TR 12603:2010:
— drilling and foundation equipment;
— equipment used for the preparation, conveyance and compaction of concrete, mortar and processing
reinforcement;
— road construction and maintenance machinery and equipment.
It deals with general EMC requirements under typical electromagnetic environmental conditions.
(ISO 13766-2:2018 deals with EMC requirements specifically related to functional safety).
Electrical/electronic subassemblies (ESA) and separate ESA intended to be fitted to the machinery are
also dealt with. The following electromagnetic disturbance phenomena are evaluated:
— broadband and narrowband electromagnetic interference;
— electromagnetic field immunity;
— electrostatic discharge;
— conducted transients.
The machinery can have DC or AC or a combination of both as the internal electrical power supply system.
This document is not applicable to machines that are designed to be supplied by an external mains
network or to phenomena caused by military applications.
NOTE 1 Grid-connected machines are covered by IEC 61000.
NOTE 2 Hybrid machines are covered in UN ECE R10-Rev. 5.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 6165:2012, Earth-moving machinery — Basic types — Identification and terms and definitions
ISO 7637-1:2015, Road vehicles — Electrical disturbances from conduction and coupling — Part 1:
Definitions and general considerations
© ISO 2018 – All rights reserved 1
---------------------- Page: 15 ----------------------
SIST EN ISO 13766-1:2018
ISO 13766-1:2018(E)
ISO 7637-2:2011, Road vehicles — Electrical disturbances from conduction and coupling — Part 2:
Electrical transient conduction along supply lines only
ISO 10605:2008, Road vehicles — Test methods for electrical disturbances from electrostatic discharge
ISO 11451-1:2015, Road vehicles — Vehicle test methods for electrical disturbances from narrowband
radiated electromagnetic energy — Part 1: General principles and terminology
ISO 11451-2:2015, Road vehicles — Vehicle test methods for electrical disturbances from narrowband
radiated electromagnetic energy — Part 2: Off-vehicle radiation sources
ISO 11451-4:2013, Road vehicles — Vehicle test methods for electrical disturbances from narrowband
radiated electromagnetic energy — Part 4: Bulk current injection (BCI)
ISO 11452-1:2015, Road vehicles — Component test methods for electrical disturbances from narrowband
radiated electromagnetic energy — Part 1: General principles and terminology
ISO 11452-2:2004, Road vehicles — Component test methods for electrical disturbances from narrowband
radiated electromagnetic energy — Part 2: Absorber-lined shielded enclosure
ISO 11452-3:2016, Road vehicles — Component test methods for electrical dis
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.