Acoustics - Noise test code for fastener driving tools - Engineering method

This standard applies to fastener driving tools. The noise created by fastener driving tools directly affecting the surrounding environment (noise emission) should calculated in a uniform procedure enabling comparison of the final results. This standard contains provisions concerning the execution of the measurement of airborne noise in the vicinity of fastener driving tools and the measurement of emission sound pressure levels at the work station under defined operating conditions.
The determination of the noise emission levels of fastener driving tools in accordance with this standard is valid for all actuating systems in accordance with EN 792-13.
The results can be used to compare the noise emissions of different fastener driving tools.
NOTE   The special conditions at the work place (e.g. shape and foundation of the workpiece, quantity and frequency of the driving processes) can influence the noise emission to an important degree.

Akustik - Geräuschmessverfahren für Eintreibgeräte - Verfahren der Genauigkeitsklasse 2

Diese Norm gilt für Eintreibgeräte. Das Geräusch, welches von Eintreibgeräten direkt in die Umgebung
abgestrahlt wird (Geräuschemission), soll nach einem einheitlichen Verfahren ermittelt werden, so dass die
Ergebnisse vergleichbar sind. Diese Norm enthält Festlegungen über die Durchführung der Messung von
Luftschall, der von Eintreibgeräten in die Umgebung abgestrahlt wird, sowie für die Messung des Emissions-
Schalldruckpegels am Arbeitsplatz unter festgelegten Betriebsbedingungen.
Die Bestimmung der Geräuschemissionswerte von Eintreibgeräten nach dieser Norm gilt für alle Auslösesysteme
entsprechend EN 792-13.
Die Ergebnisse können dazu dienen, die Geräuschemission von verschiedenen Eintreibgeräten zu
vergleichen.
ANMERKUNG Die am jeweiligen Arbeitsplatz vorhandenen Bedingungen (z. B. Werkstückgestaltung, Werkstückauflage,
Zahl und zeitlicher Verlauf der Eintreibvorgänge) können die Geräuschemission wesentlich beeinflussen.

Acoustique - Code d'essai acoustique pour les machines à enfoncer les fixations - Méthode d'expertise

Cette norme s'applique aux machines à enfoncer les fixations. Il convient de calculer le bruit créé par les machines
à enfoncer les fixations affectant directement l'environnement (émission sonore) avec un même et seul mode
opératoire permettant une comparaison des résultats finaux. Cette norme définit les conditions d'exécution du
mesurage du bruit aérien au voisinage des machines à enfoncer les fixations et de mesurage des niveaux de pression
acoustique d'émission au poste de travail dans des conditions de fonctionnement définies.
La détermination des niveaux d’émission sonore des machines à enfoncer les fixations, conformément à la présente
norme, est valide pour tous les systèmes de commande conformément à l’EN 792-13.
Les résultats peuvent être utilisés pour comparer l'émission sonore de différentes machines à enfoncer les fixations.
NOTE Les conditions particulières de fonctionnement au poste de travail (par exemple la forme de la pièce travaillée
et la façon dont elle est tenue, la quantité et la fréquence des enfoncements) peuvent influencer l'émission sonore de
façon importante.

Akustika - Postopek merjenja hrupa orodij za pritrjevanje/zabijanje - Inženirska metoda

General Information

Status
Published
Publication Date
07-Oct-2008
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
25-Sep-2008
Due Date
30-Nov-2008
Completion Date
08-Oct-2008

Relations

Buy Standard

Standard
EN 12549:2000+A1:2008
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Akustika - Postopek merjenja hrupa orodij za pritrjevanje/zabijanje - Inženirska metodaAkustik - Geräuschmessverfahren für Eintreibgeräte - Verfahren der Genauigkeitsklasse 2Acoustique - Code d'essai acoustique pour les machines à enfoncer les fixations - Méthode d'expertiseAcoustics - Noise test code for fastener driving tools - Engineering method25.140.99Other hand-held tools17.140.20Emisija hrupa naprav in opremeNoise emitted by machines and equipmentICS:Ta slovenski standard je istoveten z:EN 12549:1999+A1:2008SIST EN 12549:2000+A1:2008en,fr,de01-november-2008SIST EN 12549:2000+A1:2008SLOVENSKI
STANDARD



SIST EN 12549:2000+A1:2008



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12549:1999+A1
September 2008 ICS 17.140.20; 25.140.99 Supersedes EN 12549:1999English Version
Acoustics - Noise test code for fastener driving tools - Engineering method
Acoustique - Code d'essai acoustique pour les machines à enfoncer les fixations - Méthode d'expertise
Akustik - Geräuschmessverfahren für Eintreibgeräte - Verfahren der Genauigkeitsklasse 2 This European Standard was approved by CEN on 30 October 1998 and includes Amendment 1 approved by CEN on 26 July 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2008 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12549:1999+A1:2008: ESIST EN 12549:2000+A1:2008



EN 12549:1999+A1:2008 (E) 2 Contents Page Foreword.4 Introduction.5 1 Scope.5 2 Normative references.5 3 Definitions.6 4 Description of fastener driving tools.6 5 Sound power level determination.6 5.1 Basic International Standards to be used.6 5.2 Measurement procedure.7 5.3 Calculation.8 5.4 Measurement uncertainty.8 6 Emission sound pressure level determination.9 6.1 Basic International Standards to be used.9 6.2 Selection of relevant work station.9 6.3 Measurement procedure.9 6.4 Measurement uncertainty.9 7 Installation and mounting conditions.9 7.1 General.9 7.2 Measuring instruments.10 7.3 Test environment.10 8 Operating conditions.10 8.1 General.10 8.2 Object to be measured and operating conditions.10 8.3 Workpiece.10 8.4 Workpiece support.11 8.5 Position of the fastener driving tool.11 9 Measurement uncertainties.11 10 Information to be recorded.11 10.1 General.11 10.2 Type and technical information on the fastener driving tool and the fasteners to be used (including limits).11 10.3 Information about the operating conditions.11 10.4 Description of the measurement installation and surroundings.11 10.5 Measurement instruments used.11 10.6 Measured values and calculated results, containing.11 11 Information to be reported.12 12 Declaration and verification of noise emission values.12 Annex A (informative)
Calculation of equivalent continuous emission sound pressure level.13 Annex B (informative)
Model form for the declaration of noise emission values of fastener driving tools operated with compressed air.14 Annex C (informative)
Bibliography.15 SIST EN 12549:2000+A1:2008



EN 12549:1999+A1:2008 (E) 3 Annex ZA (informative)
!Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC".16 Annex ZB (informative)
!Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC".17
SIST EN 12549:2000+A1:2008



EN 12549:1999+A1:2008 (E) 4 Foreword This document (EN 12549:1999+A1:2008) has been prepared by Technical Committee CEN/TC 255 "Hand-held, non-electric power tools - Safety", the secretariat of which is held by SIS. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2009, and conflicting national standards shall be withdrawn at the latest by December 2009. This document includes Amendment 1, approved by CEN on 2008-07-26. This document supersedes EN 12549:1999. The start and finish of text introduced or altered by amendment is indicated in the text by tags ! ". This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). !For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this document." According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
SIST EN 12549:2000+A1:2008



EN 12549:1999+A1:2008 (E) 5 Introduction This noise test code describes methods for determining and presenting the acoustical characteristics of fastener driving tools. The EC Machinery Directive prescribes that noise emission values for the machines in a defined process shall be stated. The manufacturer of fastener driving tools must indicate the operating conditions during the noise measurement and what methods have been used for the measurement. 1 Scope This standard applies to fastener driving tools. The noise created by fastener driving tools directly affecting the surrounding environment (noise emission) should calculated in a uniform procedure enabling comparison of the final results. This standard contains provisions concerning the execution of the measurement of airborne noise in the vicinity of fastener driving tools and the measurement of emission sound pressure levels at the work station under defined operating conditions.
The determination of the noise emission levels of fastener driving tools in accordance with this standard is valid for all actuating systems in accordance with EN 792-13. The results can be used to compare the noise emissions of different fastener driving tools. NOTE The special conditions at the work place (e.g. shape and foundation of the workpiece, quantity and frequency of the driving processes) can influence the noise emission to an important degree. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 292-2, Safety of machinery – Basic concepts, general principles for design – Part 2: Technical principles and specifications EN 792-13, Handheld non-electric power tools - Safety requirements – Part 13: Fastener driving tools EN 60651, Sound level meters EN 60804, Integrating-averaging sound level meters EN ISO 3744, Acoustics - Determination of sound power levels of noise sources using sound pressure - Engineering method in an essentially free field over a reflecting plane EN ISO 4871, Acoustics - Declaration and verification of noise emission values of machinery and equipment EN ISO 11201, Acoustics - Noise emitted by machinery and equipment - Measurement of emission sound pressure levels at a work station and at other specified positions - Engineering method in an essentially free field over a reflecting plane SIST EN 12549:2000+A1:2008



EN 12549:1999+A1:2008 (E) 6 3 Definitions For the purposes of this standard, the following definitions apply: 3.1 A-weighted single-event emission sound pressure level, LpA,1s in dB:
A-weighted and time-integrated emission sound pressure level of an isolated single sound event of specified duration T (or specified measurement time T), related to T0 = 1 s; it is given by the following equation: LpA,1 s = 10 lg[ 10T ∫T0202)(ptp dt ] dB = LpAeq,T + 10 lg TT0
dB
…(1) The reference sound pressure is p0 = 20 µPa. 3.2 A-weighted single-event sound power level, LWA,1s in dB: A-weighted sound power level determined from measurements of the single-event sound pressure level. 3.3 C-weighted peak emission sound pressure level, LpC,peak in dB: The C-weighted peak emission sound pressure level of a test object, determined in accordance with EN ISO 11201 at the work station. 3.4 Fastener driving tool See EN 792-13. 4 Description of fastener driving tools Fastener driving tools are handheld power tools in which energy is applied in a linear movement to inserted fasteners for the purpose of driving. The design of these fastener driving tools is such that in normal circumstances they may be carried by one person and are handheld during the driving process. NOTE Fastener driving tools are named e.g. nailers, staplers, tackers, pinners. The energy required for the driving process can be drawn e.g. from compressed air, electrical current, combustible gases, tension springs. Fasteners may be e.g. nails, staples, pins, brads, corrugated fasteners and screws used as nails. The frequency of the driving processes with a fastener driving tool varies in time according to the operation purpose (e.g. 500 driving processes per day may be carried out with a big fastener driving tool against 20 per second with a small one). The time duration of one driving process is normally in a range of 0,1 s or shorter. 5 Sound power level determination 5.1 Basic International Standards to be used If it is required to determine the sound power level, basic sound power measurement standards shall be used, such as EN ISO 3744. SIST EN 12549:2000+A1:2008



EN 12549:1999+A1:2008 (E) 7 The sound power level shall be given as A-weighted sound power level in dB. The reference sound power is 1pW (1 pW = 10-12 W). 5.2 Measurement procedure 5.2.1 Measurement surface The measurement surface is a hypothetical cube on which the measurement positions are located and which envelops the fastener driving tool (see figure 1). Exception: Position O for measuring the A-weighted single-event emission sound pressure level at work station. The measurement surface ends at floor level, which is to be regarded as a sound reflecting periphery. The height of the centre point of the fastener driving tool above the ground shall be (1,00 ± 0,10) m. The centre point is located on the driving axis at half of the height of the fastener driving tool. NOTE Because a fastener driving tool is of small size the centre point of a fastener driving tool is used instead of the surface. 5.2.2 Measurement distance The measurement distance shall be 1,00 m from the centre point of the fastener driving tool (see figure 1). 5.2.3 Measurement positions The location of the nine measurement positions i = 1, 2, ., 9 shall be that of figure 1. Dimensions in metres
Measurement positions 0
Measurement position at the wor
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.