SIST EN ISO 18847:2024
(Main)Solid biofuels - Determination of particle density of pellets and briquettes (ISO 18847:2024)
Solid biofuels - Determination of particle density of pellets and briquettes (ISO 18847:2024)
ISO 18847:2016 specifies the method for determining the particle density of compressed fuels such as pellets or briquettes. Particle density is not an absolute value and conditions for its determination have to be standardized to enable comparative determinations to be made.
Biogene Festbrennstoffe - Bestimmung der Partikeldichte von Pellets und Briketts (ISO 18847:2024)
Dieses Dokument legt ein Verfahren zur Bestimmung der Partikeldichte von gepressten Brennstoffen, wie z. B. Pellets oder Briketts, fest. Die Partikeldichte ist kein absoluter Wert, und die Bedingungen für deren Bestimmung müssen genormt werden, um vergleichbare Bestimmungen vornehmen zu können.
Biocombustibles solides - Détermination de la masse volumique unitaire des granulés et des briquettes (ISO 18847:2024)
ISO 18847:2016 spécifie la méthode de détermination de la masse volumique unitaire des combustibles comprimés tels que les granulés ou les briquettes. La masse volumique unitaire n'est pas une valeur absolue et les conditions nécessaires à sa détermination doivent être normalisées afin de pouvoir comparer les différentes déterminations.
Trdna biogoriva - Določevanje gostote delcev peletov in briketov (ISO 18847:2024)
Standard ISO 18847:2016 določa metodo za določevanje gostote delcev v stisnjenih gorivih, kot so peleti in briketi. Gostota delcev ni absolutna vrednost in pogoje za njeno določitev je treba standardizirati, da se omogoči primerjalno določevanje.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2024
Nadomešča:
SIST EN ISO 18847:2016
Trdna biogoriva - Določevanje gostote delcev peletov in briketov (ISO 18847:2024)
Solid biofuels - Determination of particle density of pellets and briquettes (ISO
18847:2024)
Biogene Festbrennstoffe - Bestimmung der Partikeldichte von Pellets und Briketts (ISO
18847:2024)
Biocombustibles solides - Détermination de la masse volumique unitaire des granulés et
des briquettes (ISO 18847:2024)
Ta slovenski standard je istoveten z: EN ISO 18847:2024
ICS:
17.060 Merjenje prostornine, mase, Measurement of volume,
gostote, viskoznosti mass, density, viscosity
27.190 Biološki viri in drugi Biological sources and
alternativni viri energije alternative sources of energy
75.160.40 Biogoriva Biofuels
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 18847
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2024
EUROPÄISCHE NORM
ICS 27.190; 75.160.40 Supersedes EN ISO 18847:2016
English Version
Solid biofuels - Determination of particle density of pellets
and briquettes (ISO 18847:2024)
Biocombustibles solides - Détermination de la masse Biogene Festbrennstoffe - Bestimmung der
volumique unitaire des granulés et des briquettes (ISO Partikeldichte von Pellets und Briketts (ISO
18847:2024) 18847:2024)
This European Standard was approved by CEN on 20 April 2024.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 18847:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 18847:2024) has been prepared by Technical Committee ISO/TC 238 "Solid
biofuels" in collaboration with Technical Committee CEN/TC 335 “Solid biofuels” the secretariat of
which is held by SIS.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2024, and conflicting national standards
shall be withdrawn at the latest by November 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 18847:2016.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 18847:2024 has been approved by CEN as EN ISO 18847:2024 without any modification.
International
Standard
ISO 18847
Second edition
Solid biofuels — Determination
2024-04
of particle density of pellets and
briquettes
Biocombustibles solides — Détermination de la masse volumique
unitaire des granulés et des briquettes
Reference number
ISO 18847:2024(en) © ISO 2024
ISO 18847:2024(en)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 18847:2024(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Reagents . 1
6 Apparatus . 2
6.1 General apparatus requirements .2
6.2 Apparatus for pellet testing .2
6.3 Apparatus for briquette testing .3
7 Sample preparation . 4
7.1 General apparatus requirements .4
8 Procedures . 5
8.1 Procedure for pellets .5
8.2 Procedure for briquettes .6
9 Calculation . 6
10 Performance characteristics . 7
10.1 General .7
10.2 Repeatability .7
10.3 Reproducibility . .7
11 Test report . 7
Annex A (informative) Stereometric volume estimation . 8
Annex B (informative) Estimation of the particle density of pellets by liquid displacement .12
Bibliography . 14
iii
ISO 18847:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 238, Solid biofuels, in collaboration with
the European Committee for Standardization (CEN) Technical Committee CEN/TC 335, Solid biofuels, in
accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 18847:2016), which has been technically
revised.
The main changes are as follows:
— editorial changes made;
— ISO 21945 inserted as a normative reference;
— method for the determination of particle density is specified in more detail;
— informative Annex B on a liquid displacement method to estimate the particle density of pellets added.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.