73.100.30 - Equipment for drilling and mine excavation

This document specifies requirements for wire-reinforced hoses and hose assemblies for underground coal mining applications of nominal sizes 6,3 to 51 for use with: — oil-based hydraulic fluids HH, HL, HM, HR and HV as defined in ISO 6743-4 at temperatures ranging from −40 °C to +120 °C; — water-based fluids HFC, HFAE, HFAS and HFB as defined in ISO 6743-4 at temperatures ranging from −40 °C to +70 °C; — water at temperatures ranging from 0 °C to +70 °C. There is a possibility that operation at ...view more

2019-09-17 JF: TC request for the editorial change in Annex ZA to adress the Consultant's comment
2019-03-19 The Enquiry draft of the standard had not been submitted for the assessment. In February, the TC provided a detailed Annex ZA  in line with the general EC request. CCMC requested the missing assessment on 2019-03-19. The indicative deadline to receive it is 2019-04-24.

2019-09-17 JF: TC request for the editorial change in Annex ZA to adress the Consultant's comment
2019-03-19 The Enquiry draft of the standard had not been submitted for the assessment. In February, the TC provided a detailed Annex ZA  in line with the general EC request. CCMC requested the missing assessment on 2019-03-19. The indicative deadline to receive it is 2019-04-24.

2018-05-03 CV: CEN BT C218/2017 - decision: new Annex ZA to be published as amendment prior to offer EN ISO/IEC 80079-39:2016 + amd for citation in the OJEU

This document defines terms relating to rock drill rigs and rock reinforcement rigs, including their intended use, working methods, types, and main components. It also provides (see Annex A) several classifications of rock drill rigs, based on intended use, mobility and type of operation. The primary use of this document is in instruction handbooks for rock drill rigs and in marketing material. Safety related terminology is used in ISO 18758‑2. This document is not applicable to drill rigs for s...view more

This document specifies the safety requirements for rock drill rigs and rock reinforcement rigs designed for the following underground or surface operations: a) blast hole drilling; b) rock reinforcement; c) drilling for secondary breaking; d) dimensional stone drilling; e) mineral prospecting, e.g. utilizing core drilling or reverse circulation; f) water and methane drainage drilling; g) raise boring. NOTE Rigs can be designed for more than one of the operations above. See ISO 18758-1 for vocab...view more

This European Standard specifies safety requirements which shall be met to minimize the hazards
listed in clause 4 that may occur during the assembly, use, maintenance, repair, decommissioning,
disassembly and disposal of shearer loaders and plough systems when operated in accordance with the
manufacturer’s requirements in underground mining.
The machines work with tools for cutting minerals such as coal, ore, salt and surrounding rock, at a fixed or
variable height and are guided on armoured fa...view more

ISO 19225:2017 specifies safety requirements to minimize the hazards listed in Clause 4 that can occur during the assembly, use, maintenance, repair, decommissioning, disassembly and disposal of shearer loaders and plough systems when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, in underground mining.
ISO 19225:2017 does not cover any hazards resulting from explosive atmospheres. Requirements for explosive atmospheres can be found in ISO/...view more

ISO 19224:2017 deals with safety requirements for continuous surface miners (CSM). It specifies common requirements for the design and construction of CSM to protect workers from accidents and health hazards that can occur during operation, loading, transport and maintenance. ISO 19224:2017 deals with known significant hazards, hazardous situations or hazardous events relevant to CSM, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufactur...view more

ISO 19225:2017 specifies safety requirements to minimize the hazards listed in Clause 4 that can occur during the assembly, use, maintenance, repair, decommissioning, disassembly and disposal of shearer loaders and plough systems when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, in underground mining. ISO 19225:2017 does not cover any hazards resulting from explosive atmospheres. Requirements for explosive atmospheres can be found in ISO/I...view more

This International Standard specifies the explosion protection requirements for the design, construction, assessment and information for use (maintenance, repair, marking) of equipment that may be an individual item or form an assembly. This
includes machinery and components placed on the market by a single supplier for use in mines susceptible to explosive atmospheres of firedamp and/or combustible dust. The standard atmospheric conditions (relating to the explosion characteristics
of the atmo...view more

ISO/IEC 80079-38:2016 is published as a dual logo standard and specifies the explosion protection requirements for the design, construction, assessment and information for use (maintenance, repair, marking) of equipment that may be an individual item or form an assembly. This includes machinery and components for use in mines susceptible to explosive atmospheres of firedamp and/or combustible dust. The standard atmospheric conditions (relating to the explosion characteristics of the atmosphere) ...view more

This part of ISO 10097 specifies the nomenclature and the leading dimensions necessary for the interchangeability
of the following wireline drilling equipment for drilling holes of diameter 1,890 in to 3,790 in, yielding cores of
diameter 1,063 in to 2,500 in.
The equipment is illustrated in Figure 1 and comprises the following:
a) core bit;
b) reaming shell;
c) core lifter;
d) core lifter case;
e) outer tube;
f) inner tube;
g) drill rod (smooth pipe only).

This part of ISO 10097 specifies the nomenclature and the leading dimensions necessary for the interchangeability
of the following wireline drilling equipment for drilling holes 48 mm to 96 mm in diameter, yielding cores of 27 mm to
63 mm in diameter.
The equipment is illustrated in Figure 1 and comprises the following:
a) core bit;
b) reaming shell;
c) core lifter;
d) core lifter case;
e) outer tube;
f) inner tube;
g) drill rod (smooth pipe only).

Establishes the nomenclature and lays down the leading dimensions to ensure interchangeability within the limits of system A of the following equipment: drill rods and couplings; casings, casing couplings, casing bits, casing shoes, drive shoes and casing ream shells; core barrels, core bits, core lifters and reaming shells. Specifies the characteristics of a range of equipment for drilling holes having diameters from 1.18 in to 7.88 in and yielding cores having diameters from 0.73 in to 6.5 in.

Changes in Figure 20 (page 21) "Type DM" to "Type DT".

Figure 13: change the value for the dimension D for type M(DM)59C from 49 to 44,3. Figure 30: change the value for the dimension Dx for type DP76C from 75 to 76.

Establishes the nomenclature and lays down the leading dimensions to ensure interchangeability within the limits of system B of the following equipment: drill rods and couplings, fishing rods and couplings; casing tubes, casing drive shoes, casing shoe bits, casing bits and sediment tubes; core barrels, core bits, core lifters and reaming shells. Specifies the characteristics of a range of equipment for drilling holes having diameters from 1.42 in to 5.74 in and yielding cores from 0.87 in to 4....view more