EN ISO 6947:1997

Welds - Working positions - Definitions of angles of slope and rotation (ISO 6947:1993)

Defines fundamental welding positions and makes possible the location in space of straight welds by means of slope and rotation. Cancels and replaces the recommendations ISO/R 598-1967 and ISO/R 627-1967.

Schweißnähte - Arbeitspositionen - Definitionen der Winkel von Neigung und Drehung (ISO 6947:1993)

Diese Europäische Norm beschreibt die Arbeitspositionen und ermöglicht es, die räumliche Lage der Schweißnähte in Bezug auf eine horizontale Ebene (gewöhnlich parallel zum Werkstattboden) durch den jeweiligen Neigungs- und Drehwinkel festzulegen. Dies ist unabhängig von der umgebenden Konstruktion.

Soudures - Positions de travail - Définitions des angles d'inclinaison et de rotation (ISO 6947:1993)

La présente Norme internationale prescrit les positions de travail et permet la localisation des soudures dans l'espace par rapport à un plan horizontal de référence (généralement parallèle au sol de l'atelier) au moyen d'angles d'inclinaison et de rotation qui ne sont pas liés à la construction environnante.

Zvari - Položaji pri varjenju - Definicije kotov nagiba in zasuka (ISO 6947:1993)

General Information

• Status: Withdrawn
• Publication Date: 21-Jan-1997
• Withdrawal Date: 14-May-2011
• ICS: 01.040.25 - Manufacturing engineering (Vocabularies)
• ICS: 25.160.40 - Welded joints and welds
• Technical Committee: CEN/TC 121 - Welding
• Drafting Committee: CEN/TC 121 - Welding
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 15-May-2011
• Completion Date: 15-May-2011
• Directive: 97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Ref Project: SIST EN ISO 6947:1999 - Welds - Working positions - Definitions of angles of slope and rotation (ISO 6947:1993)

Relations

• Replaced By: EN ISO 6947:2011 - Welding and allied processes - Welding positions (ISO 6947:2011)
• Effective Date: 22-Dec-2008

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 6947:1999
01-december-1999
Zvari - Položaji pri varjenju - Definicije kotov nagiba in zasuka (ISO 6947:1993)
Welds - Working positions - Definitions of angles of slope and rotation (ISO 6947:1993)
Schweißnähte - Arbeitspositionen - Definitionen der Winkel von Neigung und Drehung
(ISO 6947:1993)
Soudures - Positions de travail - Définitions des angles d'inclinaison et de rotation (ISO
6947:1993)
Ta slovenski standard je istoveten z: EN ISO 6947:1997
ICS:
01.040.25 Izdelavna tehnika (Slovarji) Manufacturing engineering
(Vocabularies)
25.160.40 Varjeni spoji in vari Welded joints
SIST EN ISO 6947:1999 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

ISO
INTERNATIONAL
6947
STANDARD
Second edition
1990-02-01
Corrected and reprinted
1 993-05-01
Welds - Working positions - Definitions of
angles of slope and rotation
(Revision of ISO 6947 : 1980)
Positions de travail -
Soudures - D&Ynitions des angles &inclihaison et de
rotation
Reference number
ISO 6947 : 1990 (El

---------------------- Page: 2 ----------------------

ISO 6947 : 1990 (El
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of
national Standards bodies (ISO member bedies). The work of preparing International
Standards is normally carried out through ISO technical committees. Esch member
body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, govern-
mental and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission (IEC) on all
matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are circulated to
the member bodies for approval before their acceptance as International Standards by
the ISO Council. They are approved in accordance with ISO procedures requiring at
least 75 % approval by the member bodies voting.
International Standard ISO 6947 was prepared by Technical Committee ISO/TC 44,
Welding and allied processes.
This second edition cancels and replaces the first edition (ISO 6947 : 19801, of which it
constitutes a technical revision; reasons for the revision are given in the “lntroduction”
(p. iii).
0 ISO 1990
All rights reserved. No part of this publication may be reproduced or utilized in any form or by any
means, electronie or mechanical, including photocopying and microfilm, without Permission in
writing from the publisher.
International Organization for Standardization
d
Case postale 56 l CH-121 1 Geneve 20 l Switzerlan
Printed in Switzerland
ii

---------------------- Page: 3 ----------------------

ISO 6947 : 1990 (El
lntroduction
The main reasons for the revision of ISO 6947 : 1980 are given below.
The working positions should be valid for welds in plates and pipes.
The direction of welding is an essential Parameter for determining the working posi-
tion, e.g. up or down; however, in ISO 6947 : 1980, the working direction was not dealt
with.
The working Position is not dependent on the geometrical arrangement of the joint,
e.g. butt or fillet joint, or that of the semi-finished product
The limitations for slope (within O” to 90°) and for rotation (up to a maximum of 1800),
as specified in ISO 6947 : 1980 (clockwise or counter-clockwise), prevent the complete
specification of the weld and the direction of welding in space; it could not, therefore,
be applicable for automatic and robotic welding. lt is intended in this second edition of
ISO 6947 that the whole sphere be included so that welds in all types and all directions
a re covered .
To avoid any misunderstanding, the main positions have been given Symbols which
tan easily be used for designation purposes; these Symbols were Chosen independent-
ly of possible meaningful abbreviations, i.e. they are not derived from any particular
language.
The centreline is normally identical with the Position of the stick electrode. The main
positions have been defined without any tolerantes for slope and rotation. For some
stick electrodes, it may be useful to add the required tolerantes as necessary for their
application. In such cases, the main Position, e.g. flat Position, tan be supplemented
by specifying limits of slope and rotation.
. . .
Ill

---------------------- Page: 4 ----------------------

This page intentionally leff blank

---------------------- Page: 5 ----------------------

ISO 6947 : 1990 (E)
INTERNATIONAL STANDARD
- Working positions - Definitions of angles of
Welds
slope and rotation
The Co-Ordinate System shall be arranged so that the root line
1 Scope
lies in the vertical reference plane Wz-plane; see figure 1) and
that the working direction radi
...