IEC 60745-2-14:2003/AMD2:2010

Amendment 2 - Hand-held motor-operated electric tools - Safety - Part 2-14: Particular requirements for planers

Gives recommendations on the data to be measured to enable an operator to diagnose developing deviations from normal functioning so as to take corrective action at an early stage. (Text identical with Annex 11 to IAEA Safety Guide No. 50-SG-D12.)

Amendement 2 - Outils électroportatifs à moteur - Sécurité - Partie 2-14: Règles particulières pour les rabots

Fournit des recommandations sur les données à mesurer pour permettre à l'opérateur d'établir un diagnostic des écarts évolutifs par rapport au fonctionnement normal afin de prendre suffisamment tôt des actions correctives. (Texte identique à l'Annexe II du Guide N° 50-SG-D12 de l'AIEA.)

General Information

• Status: Published
• Publication Date: 25-May-2010
• ICS: 01 - GENERALITIES. TERMINOLOGY. STANDARDIZATION. DOCUMENTATION
• ICS: 25.140.20 - Electric tools
• ICS: 27.120.20 - Nuclear power plants. Safety
• Technical Committee: TC 116 - Safety of motor-operated electric tools
• Drafting Committee: MT 4 - TC 116/MT 4
• Current Stage: PPUB - Publication issued
• Start Date: 15-Jun-2010
• Completion Date: 26-May-2010

Relations

• Amends: IEC 60745-2-14:2003 - Hand-held motor-operated electric tools - Safety - Part 2-14: Particular requirements for planers
• Effective Date: 05-Sep-2023

Standards Content (Sample)

IEC 60745-2-14 ®
Edition 2.0 2010-05
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
AMENDMENT 2
AMENDEMENT 2
Hand-held motor-operated electric tools – Safety –
Part 2-14: Particular requirements for planers

Outils électroportatifs à moteur – Sécurité –
Partie 2-14: Règles particulières pour les rabots

IEC 60745-2-14:2003/A2:2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or
IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.

IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: [e-mail]
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: [e-mail]
Tel.: [phone]
Fax: [phone]
A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.

A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
ƒ Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm
Le Catalogue en-ligne de la CEI vous permet d’effectuer des recherches en utilisant différents critères (numéro de référence,
texte, comité d’études,…). Il donne aussi des informations sur les projets et les publications retirées ou remplacées.
ƒ Just Published CEI: www.iec.ch/online_news/justpub
Restez informé sur les nouvelles publications de la CEI. Just Published détaille deux fois par mois les nouvelles
publications parues. Disponible en-ligne et aussi par email.
ƒ Electropedia: www.electropedia.org
Le premier dictionnaire en ligne au monde de termes électroniques et électriques. Il contient plus de 20 000 termes et
définitions en anglais et en français, ainsi que les termes équivalents dans les langues additionnelles. Egalement appelé
Vocabulaire Electrotechnique International en ligne.
ƒ Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm
Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du
Service clients ou contactez-nous:
Email: [e-mail]
Tél.: [phone]
Fax: [phone]
IEC 60745-2-14 ®
Edition 2.0 2010-05
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
AMENDMENT 2
AMENDEMENT 2
Hand-held motor-operated electric tools – Safety –
Part 2-14: Particular requirements for planers

Outils électroportatifs à moteur – Sécurité –
Partie 2-14: Règles particulières pour les rabots

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
F
CODE PRIX
ICS 25.140.20 ISBN 978-2-88910-937-1
– 2 – 60745-2-14 Amend. 2 © IEC:2010
FOREWORD
This amendment has been prepared by IEC committee 116: Safety of hand-held motor-
operated electric tools.
The text of this amendment is based on the following documents:
FDIS Report on voting
116/35/FDIS 116/43/RVD
Full information on the voting for the approval of this amendment can be found in the report
on voting indicated in the above table.
This amendment modifies Part 2-14 of IEC 60745 to ensure its conformity with the fourth
edition (2006) of IEC 60745-1, Hand-held motor-operated electric tools – Safety – Part 1:
General requirements.
The committee has decided that the contents of the base publication and its amendments will
remain unchanged until the stability date indicated on the IEC web site under
“http://webstore.iec.ch” in the data related to the specific publication. At this date, the
publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
_____________
1 Scope
Replace the existing text by the following:
This clause of Part 1 is applicable except as follows:
Addition:
This standard applies to planers.
3 Definitions
Replace the title and existing text of this clause by the following:
3 Terms and definitions
This clause of Part 1 is applicable except as follows:
3.101
planer
tool intended for removing surface material, equipped with a rotating cutting head where the
axis of the cutting head is parallel to the base plate

60745-2-14 Amend. 2 © IEC:2010 – 3 –
3.102
lift-off device
device which keeps the blade(s) from making contact when the planer is placed on a flat
surface
3.103
cutting head
assembly of blades, cutter block, blade fixing elements, relevant screws and spindle, the
whole being ready for working
8 Marking and instructions
Replace the existing Subclause 8.12.1 by the following:
8.12.1.1 Addition:
Planer safety warnings
– Wait for the cutter to stop before setting the tool down. An exposed rotating cutter
may engage the surface leading to possible loss of control and serious injury.
NOTE The above warning applies only to planers without an automatic closing guard.
– Hold the power tool by insulated gripping surfaces only, because the cutter may
contact its own cord. Cutting a "live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
– Use clamps or another practical way to secure and support the workpiece to a stable
platform. Holding the work by your hand or against the body leaves it unstable and may
lead to loss of control.
19 Mechanical hazards
Replace the existing Subclause 19.1 by the following:
19.1 Addition:
For the requirements given in 19.106, 19.107 and 19.108, only the test probe shown in
Figure 102 is used.
Replac
...