This standard defines procedures to measure in laboratory the impact sound level reduction of isolated heavy landings connected to a heavy wall, isolated heavy flights of stairs connected to a heavy landing, floor or ceiling, and lightweight stairs connected to a heavy wall, floor or ceiling.
This standard also considers the characterization of isolating elements for heavy landings or heavy flights of stairs in terms of an insertion loss expressed as an impact sound level difference. The corresponding procedure is given in a normative annex (Annex A), separated from the other procedures for the sake of clarity.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies procedures to measure in laboratory the impact sound level reduction of isolated heavy landings connected to a heavy wall, isolated heavy flights of stairs connected to a heavy landing, lower or upper floor, and lightweight stairs connected to a heavy wall, lower or upper floor.
This document also considers the characterization of isolating elements for heavy landings or heavy flights of stairs in terms of an insertion loss expressed as an impact sound level difference. The corresponding procedure is given in a normative annex (Annex A), separated from the other procedures for the sake of clarity.
The tests are performed in defined test configurations and the test results are firstly restricted to the test configurations as described in the test report. The data can be used for comparing the performance of products and as input for EN ISO 12354-2:2017, Annex F, to calculate the sound pressure levels produced by the same stairs and isolating elements when installed in buildings.
The test procedures defined in this document comprise the frequency range from 50 Hz to 5000 Hz.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies requirements regarding design and test methods for power operated pedestrian doorsets. Examples of how the doorset constructions may be operated include: electro-mechanically, electro-hydraulically, electro-magnetically or pneumatically.
This document covers safety in use of power operated pedestrian doorsets used for normal access as well as in emergency and escape routes and as fire resistance and/or smoke control doorsets.
The type of doorsets covered include power operated pedestrian sliding, swing and revolving doorsets, including balanced doorsets and folding doorsets with a horizontally moving door leaf.
This document deals with all significant hazards, hazardous situations and events relevant to power operated doorsets when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.
All lifetime phases of the power operated pedestrian doorsets including transportation, assembly, dismantling, disabling and scrapping are considered by this document.
This document does not apply to:
-   vertically moving doors;
-   doors on lifts;
-   doors on vehicles;
-   power operated doors or gates mainly intended for vehicular traffic or access for goods;
-   doors used in industrial processes;
-   partition walls;
-   doors outside the reach of people (such as crane gantry fences);
-   turnstiles;
-   platform doors;
-   traffic barriers.
This document does not cover special functions of doorsets, such as security in banks, airports, etc. or fire and/or smoke compartmentation, where conformity of the specific function with requirements of the application is the preference.
This document does not deal with any specific requirements on noise emitted from power operated pedestrian doorsets as their noise emission is not considered to be a relevant hazard.
NOTE   Noise emission of power operated pedestrian doorsets is not a significant hazard for the users of these products. It is a comfort aspect.
This document is not applicable to power operated pedestrian doorsets manufactured before the date of its publication.
This document does not cover operation in environments where there is a risk of explosion.

  • Standard
    67 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies requirements regarding design and test methods for power operated pedestrian doorsets. Examples of how the doorset constructions may be operated include: electro-mechanically, electro-hydraulically, electro-magnetically or pneumatically.
This document covers safety in use of power operated pedestrian doorsets used for normal access as well as in emergency and escape routes and as fire resistance and/or smoke control doorsets.
The type of doorsets covered include power operated pedestrian sliding, swing and revolving doorsets, including balanced doorsets and folding doorsets with a horizontally moving door leaf.
This document deals with all significant hazards, hazardous situations and events relevant to power operated doorsets when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.
All lifetime phases of the power operated pedestrian doorsets including transportation, assembly, dismantling, disabling and scrapping are considered by this document.
This document does not apply to:
-   vertically moving doors;
-   doors on lifts;
-   doors on vehicles;
-   power operated doors or gates mainly intended for vehicular traffic or access for goods;
-   doors used in industrial processes;
-   partition walls;
-   doors outside the reach of people (such as crane gantry fences);
-   turnstiles;
-   platform doors;
-   traffic barriers.
This document does not cover special functions of doorsets, such as security in banks, airports, etc. or fire and/or smoke compartmentation, where conformity of the specific function with requirements of the application is the preference.
This document does not deal with any specific requirements on noise emitted from power operated pedestrian doorsets as their noise emission is not considered to be a relevant hazard.
NOTE   Noise emission of power operated pedestrian doorsets is not a significant hazard for the users of these products. It is a comfort aspect.
This document is not applicable to power operated pedestrian doorsets manufactured before the date of its publication.
This document does not cover operation in environments where there is a risk of explosion.

  • Standard
    67 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the structural performance requirements of curtain walling under wind load, both its fixed and openable parts, under positive and negative static air pressure.
This document applies to any curtain walling product as defined in EN 13830.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the structural performance requirements of curtain walling under wind load, both its fixed and openable parts, under positive and negative static air pressure.
This document applies to any curtain walling product as defined in EN 13830.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the general rules on how to select the samples of correctly stored and handled sam-ples of uninstalled bitumen, plastic or rubber sheets for waterproofing. It also specifies the procedures to be followed before the test piece is cut from the sample.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60335-2-103:2023 deals with the safety of electric drives for horizontally and vertically moving gates, doors, garage doors and windows for household and similar purposes, their rated voltage being not more than 250 V for single-phase drives and 600 V for other drives including direct current (DC) supplied appliances and battery-operated appliances. It also covers the hazards associated with the movement of the driven part.
Drives not intended for normal household use but which nevertheless can be a source of danger to the public, such as drives intended to be used by laymen in shops, offices, hotels, restaurants, hospitals, in industry and on farms, are within the scope of this standard.
Requirements for drives for doors that can be used in emergency routes and exits are given in normative Annex AA.
Examples of drives within the scope of this standard are drives for
– folding doors;
– revolving doors;
– rolling doors;
– roof windows;
– sectional overhead doors;
– swinging and sliding gates or doors.
Drives can be supplied with a driven part.
As far as is practicable, this standard deals with the common hazards presented by drives that are encountered by all persons in and around the home. However, in general, it does not take into account
– persons (including children) whose physical, sensory or mental capabilities; or lack of experience and knowledge prevents them from using the drive safely without supervision or instruction;
– children playing with the drive.
For appliances intended to be used in vehicles or on board ships or aircraft, additional requirements can be necessary. In many countries, additional requirements are specified by the national health authorities, the national authorities responsible for the protection of labour, the national water supply authorities and similar authorities.
This standard does not apply to drives
– for vertically moving garage doors for residential use (60335-2-95);
– for shutters covering doors and windows (including locations where the door is set back from the shutter), awnings, blinds and similar equipment (60335-2-97);
– intended exclusively to be used by trained persons in commercial and industrial premises;
– for specific purposes, such as fire doors;
– for natural smoke exhaust ventilators not used as windows (ISO 21927-2);
– intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas).
This standard does not apply to movement of a pedestrian door where such movement is based solely on stored energy.
This fourth edition cancels and replaces the third edition published in 2015, Amendment 1:2017 and Amendment 2:2019. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) the text has been aligned with IEC 60335-1:2020;
b) scope includes DC-supplied appliances and battery-operated appliances (Clause 1);
c) some notes have been converted to normative text (Clause 1);
d) additional requirements for installation instructions have been incorporated (7.12);
e) application of test probe 18 and test probe 19 have been introduced (8.1.1, 20.2, Annexes BB, CC and DD);
f) addition of surface temperatures for external accessible surfaces (11.3, 11.8);
g) requirements for loading accessible appliance outlets and socket outlets have been added (11.7);
h) requirements for appliances incorporating integral batteries or separable batteries have been added (11.7);
i) requirements have been added for drives intended for permanent connection delivered with a connector to ease the installation (22.108, 24.101, 25.3).
This part 2 is to be used in conjunction with the latest edition of IEC 60335-1 and its amendments unless that edition precludes it; in that case, the latest edition that does not preclude it is used. It was established on the basis of the sixth edition (2020) of tha

  • Standard
    149 pages
    English language
    sale 15% off
  • Standard
    411 pages
    English language
    sale 15% off
  • Standard
    149 pages
    English and French language
    sale 15% off

IEC 60335-2-97:2023 deals with the safety of electric drives for shutters, blinds and awnings, intended for household and similar purposes, their rated voltage being not more than 250 V for single-phase drives and 480 V for other drives, including direct current (DC) supplied appliances and battery-operated appliances.
Examples of equipment that can be driven are
– spring controlled folding arm awnings;
– curtains;
– grilles covering doors and windows;
– projection screens;
– shutters covering doors and windows;
– draperies.
Drives can be supplied with a driven part.
Drives not intended for normal household use but that nevertheless can be a source of danger to the public, such as drives intended to be used by laymen in shops, in light industry, on farms and on industrial premises, are within the scope of this standard.
As far as is practicable, this standard deals with the common hazards presented by drives that are encountered by all persons in and around the home. However, in general, it does not take into account
– persons (including children) whose physical, sensory or mental capabilities; or lack of experience and knowledge prevents them from using the drive safely without supervision or instruction;
– children playing with the drive.
For appliances intended to be used in vehicles or on board ships or aircraft, additional requirements can be necessary. In many countries, additional requirements are specified by the national health authorities, the national authorities responsible for the protection of labour, the national water supply authorities and similar authorities.
This standard does not apply to
– drives intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas);
– drives for vertically moving garage doors for residential use (IEC 60335-2-95);
– drives for gates, doors and windows (IEC 60335-2-103);
– drives used in premises such as hangars or in heavy industry;
– drives for theatre curtains.
This fourth edition cancels and replaces the third edition published in 2016 and Amendment 1: 2019. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) the text has been aligned with IEC 60335-1:2020;
b) scope includes DC-supplied appliances and battery-operated appliances (Clause 1);
c) some notes have been converted to normative text (Clause 1, 5.10, 20.101, 20.103);
d) use of artificial loads is introduced (5.10);
e) application of test probe 19 has been introduced (8.1.1, 20.2);
f) addition of surface temperatures for external accessible surfaces (11.3, 11.8);
g) requirements are added for drives intended for permanent connection delivered with a connector to ease the installation (22.102, 24.1.101, 25.3);
h) clarification for connectors that are non-detachable once engaged (24.1.5).
i) added requirements for instructions for parts of class III construction supplied from a detachable power supply part (7.12, 7.12.1).
This part 2 is to be used in conjunction with the latest edition of IEC 60335-1 and its amendments unless that edition precludes it; in that case, the latest edition that does not preclude it is used. It was established on the basis of the sixth edition (2020) of that standard.

  • Standard
    93 pages
    English language
    sale 15% off
  • Standard
    281 pages
    English language
    sale 15% off
  • Standard
    61 pages
    English and French language
    sale 15% off

This Standard defines the method of test, requirements and classification when determining the effect on a window impacted with a soft and heavy body. Any secondary moving sashes casements or fixed lights which may be mounted internally to the main casements or sashes, shall also be similarly tested. The test applies to all infillings of whatever materials including glass. The test has been devised to suit all window types, configurations and materials.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the classifications, requirements and test methods for unplasticized poly(vinyl chloride) (PVC-U) profiles covered with foils designed for external uses bonded with adhesives which are intended to be used for the fabrication of windows and doors.
NOTE 1   For editorial reasons, in this document, the term "window" is used for window/door.
NOTE 2   For the purpose of production control, test methods other than those specified in this document can be used.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard describes the method of specifying the design, installation and labelling criteria for chimney systems, construction of custom-built chimneys, the relining or converting of existing chimneys, connecting flue pipes and air supply pipes for roomsealed applications. It also gives information on commissioning of an installed chimney.
This European Standard applies to chimneys which are subject to the following limiting conditions (specified in EN 13084-1):
― the horizontal distance between the building and the outer wall of the chimney system not to
exceed 1 m,
― the distance between the supports not to exceed 4 m,
― the distance above the last structural attachment not to exceed 3 m.
This standard does not cover:
― chimneys which serve a mixture of fan assisted or forced draught burners or natural draught
appliances,
― installations having a configuration of the type C2.
NOTE Roomsealed gas appliances are classified as type C according to EN 1749.
The methods in this part of this European Standard are applicable to chimneys and connecting flue pipes for room sealed combustion appliances. The methods in Part 1 of this European Standard are applicable to chimneys and connecting flue pipes for non-room sealed combustion appliances.
For the purpose of this European Standard the term "installation" includes construction.

  • Standard
    108 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the test method, safety requirements and classification when determining the effect on a complete window or pedestrian doorset impacted with a soft and heavy body. Any secondary moving sashes, casements, leaves, mullions, transoms, T-connectors or fixed lights which can be mounted internally to the main casements or sashes, are intended to also be similarly tested and evaluated for the classification for the complete product.
The test applies to all types of infill of whatever materials including glass. It is not intended to classify the strength of the glass when used as an infill. It is intended to assess the interactions between all components of a window with particular regard to safety in use. It is also applicable to assess the ability of a doorset to keep in place glazed parts.
NOTE 1   The test method is aimed for glazed pedestrian doorsets with injury risk, but can also be used for other types of pedestrian doorsets if requested by the client.
NOTE 2   The test has been devised to suit all window or pedestrian doorset types, configurations and materials.
NOTE 3   For the classification of glass see EN 12600.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard describes the method of specifying the design, installation criteria for system chimneys, construction of custom built chimneys, and the relining of existing chimneys. It also gives information on commissioning of chimneys.
This European Standard also deals with connecting flue pipes.
This European Standard does not apply to freestanding chimneys covered by EN 13084-1.
This European Standard excludes chimneys designated H (high positive pressure chimneys) and chimneys for room-sealed heating appliances.
For the purpose of this European Standard the term "installation" includes construction.

  • Standard
    96 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the classifications, requirements and test methods for unplasticized poly(vinyl chloride) (PVC-U) profiles covered with foils designed for external uses bonded with adhesives which are intended to be used for the fabrication of windows and doors.
NOTE 1   For editorial reasons, in this document, the term "window" is used for window/door.
NOTE 2   For the purpose of production control, test methods other than those specified in this document can be used.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document defines the method to be used to determine the air permeability of curtain walling, both its fixed and openable parts. It describes how the specimen shall be tested under positive and negative air pressure.
NOTE   This document applies to any curtain walling product as defined in EN 13830.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies requirements and classification of air permeability of both fixed and openable parts of curtain walling, under positive and negative static air pressure.
NOTE   This document applies to curtain walling as specified in EN 13830.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies requirements for assessment of the mechanical strength of metal profiles incorporating a thermal barrier having mechanical performance depending on their intended use.
It also specifies the tests to determine the characteristic values of mechanical properties of the thermal barrier profile and to assess the effect of different conditionings of the thermal barrier on the mechanical performance of the connection.
Thermal barriers which do not give a contribution to the mechanical resistance of the profiles are excluded from this document.
This document applies to thermal barrier profiles designed mainly for windows, doors, screens and curtain walls. It does not apply to thermal barriers made only of metal profiles connected with metal pins or screws.

  • Standard
    63 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of EN 508 specifies requirements for self-supporting products for roof covering, wall cladding, lining, liner tray and tile products for discontinuous laying made from stainless steel sheets with or without additional metallic and/or organic coatings. Sheets intended to be used with insulation and membranes are also covered.
This document establishes general characteristics, definitions, classifications and labelling for the products, together with requirements for the materials from which the products can be manufactured. It is intended to be used either by manufacturers to ensure that their products comply with the requirements or by purchasers to verify that the products comply before they are dispatched from the factory. It specifies the requirements for products which enable them to meet all normal service conditions.
This document applies to all discontinuously laid self-supporting external profiled sheets for roof covering, wall cladding, lining, liner trays and tile products with the exception of tiles with a surface area less than 1 m2 and produced by stamping. These profiled roof sheets are designed to keep wind, rain and snow out of the building and to transfer any resultant loads and infrequent maintenance loads to the structure.
This document does not cover products for structural purposes, i.e. it does cover products used in structural class III (according to EN 1993-1-3), it does not cover products used in constructions of structural classes I and II (according to EN 1993-1-3) intended to contribute to the global or partial stability of the building structure by providing racking resistance or resistance to permanent static loads (excluding self-weight of the metal sheet).
No requirements for supporting construction, design of roof or cladding, lining, tile system and execution of connections and flashings are included.

  • Standard
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies requirements and classification of air permeability of both fixed and openable parts of curtain walling, under positive and negative static air pressure.
This document applies to curtain walling as specified in EN 13830.
NOTE   This version of EN 12152:2023 will supersede EN 12152:2002. Existing test results according to EN 12152:2002 could be considered still valid compared with this version of EN 12152.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document describes the method of specifying the design, installation and labelling criteria for chimney systems, construction of custom-built chimneys, the relining or converting of existing chimneys, connecting flue pipes and air supply pipes for room sealed combustion appliances as well as the use of chimney products. It also gives information on commissioning of an installed chimney.
This document applies to chimneys which are subject to the following limiting conditions:
-   the distance between the supports not to exceed 4 m;
-   the distance above the last structural attachment not to exceed 3 m;
-   the free-standing height above the uppermost structural support attachment for chimneys with rectangular cross section is not more than five times the smallest external dimension.
This document does not cover:
-   chimneys which serve a mixture of fan assisted or forced draught burners or natural draught appliances,
-   installations having a configuration of the type C2.
NOTE   Room sealed gas appliances are classified as type C according to EN 1749.
The methods in this part of this document are applicable to chimneys and connecting flue pipes for room sealed combustion appliances. The methods in Part 1 of this document are applicable to chimneys and connecting flue pipes for non-room sealed combustion appliances.

  • Standard
    108 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document describes the method of specifying the design, installation and labelling criteria for system chimneys, construction of custom-built chimneys, the relining of existing chimneys and connecting flue pipes for non-room sealed combustion appliances as well as the use of chimney products. It also gives information on commissioning of an installed chimney.
This document applies to chimneys which are subject to the following limiting conditions:
-   the distance between the supports not to exceed 4 m;
-   the distance above the last structural attachment not to exceed 3 m;
-   the free-standing height above the uppermost structural support attachment for chimneys with rectangular cross section is not more than five times the smallest external dimension.
The methods in this part of this document are applicable to chimneys and connecting flue pipes for non-room sealed combustion appliances. The methods in Part 2 of this document are applicable to chimneys and connecting flue pipes for room sealed combustion appliances.

  • Standard
    96 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document defines the method to be used to determine the air permeability of curtain walling, both its fixed and openable parts. It describes how the specimen shall be tested under positive and negative air pressure.
This document applies to any curtain walling product as defined in EN 13830.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies requirements for assessment of the mechanical strength of metal profiles incorporating a thermal barrier having mechanical performance depending on their intended use.
It also specifies the tests to determine the characteristic values of mechanical properties of the thermal barrier profile and to assess the effect of different conditionings of the thermal barrier on the mechanical performance of the connection.
This document does not apply to thermal barriers which do not give a contribution to the mechanical resistance of the profiles.
This document is applicable to thermal barrier profiles designed mainly for windows, doors, screens and curtain walls.
This document does not apply to thermal barriers made only of metal profiles connected with metal pins or screws.
This current edition of EN 14024 will supersede EN 14024:2004. Differences in test procedures between the two versions will not lead to significant differences in test results. Therefore, existing test results according to EN 14024:2004 are considered as equivalent to new test results according to the current edition of EN 14024.

  • Standard
    63 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of EN 508 specifies requirements for self-supporting products for roof covering, wall cladding, lining, liner tray and tile products for discontinuous laying made from stainless steel sheets with or without additional metallic and/or organic coatings. Sheets intended to be used with insulation and membranes are also covered.
This document establishes general characteristics, definitions, classifications and labelling for the products, together with requirements for the materials from which the products can be manufactured. It is intended to be used either by manufacturers to ensure that their products comply with the requirements or by purchasers to verify that the products comply before they are dispatched from the factory. It specifies the requirements for products which enable them to meet all normal service conditions.
This document applies to all discontinuously laid self-supporting external profiled sheets for roof covering, wall cladding, lining, liner trays and tile products with the exception of tiles with a surface area less than 1 m2 and produced by stamping. These profiled roof sheets are designed to keep wind, rain and snow out of the building and to transfer any resultant loads and infrequent maintenance loads to the structure.
This document does not cover products for structural purposes, i.e. it does cover products used in structural class III (according to EN 1993-1-3), it does not cover products used in constructions of structural classes I and II (according to EN 1993-1-3) intended to contribute to the global or partial stability of the building structure by providing racking resistance or resistance to permanent static loads (excluding self-weight of the metal sheet).
No requirements for supporting construction, design of roof or cladding, lining, tile system and execution of connections and flashings are included.

  • Standard
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This clause of Part 1 is replaced by the following.
This part of IEC 60335 deals with the safety of electric drives for garage doors for residential
use that open and close in a vertical direction, the rated voltage of the drives being not more
than 250 V for single-phase appliances and 480 V for other appliances. It also covers the
hazards associated with the movement of these electrically driven garage doors.
NOTE 101 Examples of garage doors are shown in Figure 101.
NOTE 102 The drive can be supplied with a garage door.
NOTE 103 This standard also applies to entrapment protection devices for use with drives. It does not cover
hazards related to the mechanisms of the door itself.
As far as is practicable, this standard deals with the common hazards presented by
appliances that are encountered by all persons in and around the home. However, in general,
it does not take into account playing with the appliance by young children, but recognizes that
children may be in the vicinity of the garage door.
NOTE 104 Attention is drawn to the fact that in many countries additional requirements are specified by the
national authorities responsible for the protection of labour and similar authorities.
NOTE 105 This standard does not apply to drives
– for shutters, awnings, blinds and similar equipment (IEC 60335-2-97);
– for gates, doors and windows (IEC 60335-2-103);
– for commercial and industrial purposes;
– intended to be used in locations where special conditions prevail, such as the presence of a corrosive or
explosive atmosphere (dust, vapour or gas).

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard deals with the safety of electric drives for horizontally and vertically moving gates, doors, garage doors and windows for household and similar purposes, their rated voltage being not more than 250 V for single-phase drives and 480 V for other drives. It also covers the hazards associated with the movement of the driven part.

  • Amendment
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard deals with the safety of electric drives for horizontally and vertically moving gates, doors, garage doors and windows for household and similar purposes, their rated voltage being not more than 250 V for single-phase drives and 480 V for other drives. It also covers the hazards associated with the movement of the driven part.

  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard deals with the safety of electric drives for shutters, blinds and awnings, intended for household and similar purposes, their rated voltage being not more than 250 V for single-phase drives and 480 V for other drives

  • Amendment
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60335-2-103:2015(E) deals with the safety of electric drives for horizontally and vertically moving gates, doors, garage doors and windows for household and similar purposes, their rated voltage being not more than 250 V for single-phase drives and 480 V for other drives. It also covers the hazards associated with the movement of the driven part. Battery-operated drives and other d.c. supplied drives are within the scope of this standard. Dual supply drives, either mains-supplied or battery-operated, are regarded as battery-operated drives when operated in the battery mode. Drives not intended for normal household use but which nevertheless may be a source of danger to the public, such as drives intended to be used by laymen in shops, offices, hotels, restaurants, hospitals, in industry and on farms, are within the scope of this standard.
Requirements for drives for doors that may be used in emergency routes and exits are given in Annex AA. Examples of drives within the scope of this standard are drives for:
- folding doors;
- revolving doors;
- rolling doors;
- roof windows;
- sectional overhead doors;
- swinging and sliding gates or doors. As far as is practicable, this standard deals with the common hazards presented by drives that are encountered by all persons in and around the home. However, in general, it does not take into account persons (including children) whose physical, sensory or mental capabilities; or lack of experience and knowledge prevents them from using the drive safely without supervision or instruction or children playing with the drive. It was established on the basis of the fifth edition (2010) of that standard. This third edition cancels and replaces the second edition published in 2006 and its Amendment 1 (2010). It constitutes a technical revision. The principal changes in this edition as compared with the second edition of IEC 60335-2-103 are as follows (minor changes are not listed): modification of requirements in Clause 20 by introduction of new annexes. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this standard be adopted for implementation nationally not earlier than 12 months or later than 36 months from the date of its publication.
Key words: Drives, Gates, Doors, Windows.

  • Standard
    69 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the requirements for eaves gutters made of unplasticized poly(vinyl chloride) (PVC-U), fittings and the system intended to be used for rainwater roof drainage.
It applies to:
-   solid wall monolayer gutters;
-   solid wall multilayer gutters;
-   solid wall fittings.
The test parameters for the test methods are specified in the document.
Gutters covered by this document can be used in conjunction with fittings of acrylic materials provided these products meet the applicable requirements of this document.
NOTE 1   Products complying with this document can be used in conjunction with rainwater downpipes conforming to EN 12200-1 [1] and fixed with brackets complying with EN 1462 [2].
This document is applicable to PVC-U gutter systems of any shape with rubber seal or adhesive joints.
NOTE 2   It is the responsibility of the purchaser or specifier to make the appropriate selections from the size range and the design to take into account their particular requirements and any relevant national regulations and installation practices or codes.
NOTE 3   The term "rainwater" in this document is used also to encompass "surface water" (as defined in EN 752 [3]) run-off from buildings.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This clause of Part 1 is replaced by the following.
This International Standard deals with the safety of electric drives for shutters, blinds and awnings, intended for household and similar purposes, their rated voltage being not more than 250 V for single-phase drives and 480 V for other drives.
NOTE 101 Battery-operated drives and other d.c. supplied drives are within the scope of this standard.
NOTE 102 Examples of equipment that can be driven are
– spring controlled folding arm awnings;
– curtains;
– grilles covering doors and windows;
– projection screens;
– shutters covering doors and windows;
– draperies.
Examples are shown in Figure 101.
NOTE 103 Drives may be supplied with a driven part.
Drives not intended for normal household use but that nevertheless may be a source of danger to the public, such as drives intended to be used by laymen in shops, in light industry, on farms and on industrial premises, are within the scope of this standard.
As far as is practicable, this standard deals with the common hazards presented by drives that are encountered by all persons in and around the home. However, in general, it does not take into account
– persons (including children) whose
• physical, sensory or mental capabilities; or
• lack of experience and knowledge
prevents them from using the drive safely without supervision or instruction;
– children playing with the drive.
NOTE 104 Attention is drawn to the fact that
– for drives intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary;
– in many countries, additional requirements are specified by the national health authorities, the national authorities responsible for the protection of labour and similar authorities.
NOTE 105 This standard does not apply to
– drives intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas);
– drives for vertically moving garage doors for residential use (IEC 60335-2-95);
– drives for rolling doors (IEC 60335-2-103);
– drives used in premises such as hangars or in heavy industry;
– drives for theatre curtains.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard deals with the safety of electric drives for garage doors for residential use that open and close in a vertical direction, the rated voltage of the drives being not more than 250 V for single-phase appliances and 480 V for other appliances.

  • Amendment
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard deals with the safety of electric drives for shutters, blinds and awnings, intended for household and similar purposes, their rated voltage being not more than 250 V for single-phase drives and 480 V for other drives

  • Amendment
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard deals with the safety of electric drives for horizontally and vertically moving gates, doors, garage doors and windows for household and similar purposes, their rated voltage being not more than 250 V for single-phase drives and 480 V for other drives. It also covers the hazards associated with the movement of the driven part.

  • Amendment
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard deals with the safety of electric drives for horizontally and vertically moving gates, doors, garage doors and windows for household and similar purposes, their rated voltage being not more than 250 V for single-phase drives and 480 V for other drives. It also covers the hazards associated with the movement of the driven part.

  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard deals with the safety of electric drives for shutters, blinds and awnings, intended for household and similar purposes, their rated voltage being not more than 250 V for single-phase drives and 480 V for other drives

  • Amendment
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard deals with the safety of electric drives for horizontally and vertically moving gates, doors, garage doors and windows for household and similar purposes, their rated voltage being not more than 250 V for single-phase drives and 480 V for other drives. It also covers the hazards associated with the movement of the driven part.

  • Amendment
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard deals with the safety of electric drives for horizontally and vertically moving gates, doors, garage doors and windows for household and similar purposes, their rated voltage being not more than 250 V for single-phase drives and 480 V for other drives. It also covers the hazards associated with the movement of the driven part.

  • Amendment
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60335-2-103:2015(E) deals with the safety of electric drives for horizontally and vertically moving gates, doors, garage doors and windows for household and similar purposes, their rated voltage being not more than 250 V for single-phase drives and 480 V for other drives. It also covers the hazards associated with the movement of the driven part. Battery-operated drives and other d.c. supplied drives are within the scope of this standard. Dual supply drives, either mains-supplied or battery-operated, are regarded as battery-operated drives when operated in the battery mode. Drives not intended for normal household use but which nevertheless may be a source of danger to the public, such as drives intended to be used by laymen in shops, offices, hotels, restaurants, hospitals, in industry and on farms, are within the scope of this standard. Requirements for drives for doors that may be used in emergency routes and exits are given in Annex AA. Examples of drives within the scope of this standard are drives for: - folding doors; - revolving doors; - rolling doors; - roof windows; - sectional overhead doors; - swinging and sliding gates or doors. As far as is practicable, this standard deals with the common hazards presented by drives that are encountered by all persons in and around the home. However, in general, it does not take into account persons (including children) whose physical, sensory or mental capabilities; or lack of experience and knowledge prevents them from using the drive safely without supervision or instruction or children playing with the drive. It was established on the basis of the fifth edition (2010) of that standard. This third edition cancels and replaces the second edition published in 2006 and its Amendment 1 (2010). It constitutes a technical revision. The principal changes in this edition as compared with the second edition of IEC 60335-2-103 are as follows (minor changes are not listed): modification of requirements in Clause 20 by introduction of new annexes. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this standard be adopted for implementation nationally not earlier than 12 months or later than 36 months from the date of its publication. Key words: Drives, Gates, Doors, Windows.

  • Standard
    69 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard deals with the safety of electric drives for shutters, blinds and awnings, intended for household and similar purposes, their rated voltage being not more than 250 V for single-phase drives and 480 V for other drives

  • Amendment
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60335-2-97:2016 deals with the safety of electric drives for shutters, blinds and awnings, intended for household and similar purposes, their rated voltage being not more than 250 V for single-phase drives and 480 V for other drives. Battery-operated drives and other d.c. supplied drives are within the scope of this standard. Examples of equipment that can be driven are: - spring controlled folding arm awnings; - curtains; - grilles covering doors and windows; - projection screens; - shutters covering doors and windows and draperies. Drives may be supplied with a driven part. Drives not intended for normal household use but that nevertheless may be a source of danger to the public, such as drives intended to be used by laymen in shops, in light industry, on farms and on industrial premises, are within the scope of this standard. Attention is drawn to the fact that for drives intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary. This standard does not apply to - drives intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas); - drives for vertically moving garage doors for residential use (IEC 60335-2-95); - drives for rolling doors (IEC 60335-2-103); - drives used in premises such as hangars or in heavy industry and drives for theatre curtains. As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by all persons in and around the home. However, in general, it does not take into account: - persons (including children) whose physical, sensory or mental capabilities or lack of experience and knowledge prevents them from using the appliance safely without supervision or instruction or - children playing with the appliance. This third edition cancels and replaces the second edition published in 2002 including its Amendment 1 (2004) and its Amendment 2 (2008). It constitutes a technical revision. The principal changes in this edition as compared with the second edition of IEC 60335-2-97 are as follows (minor changes are not listed): - Deleted "rolling" from the title and modified the scope to cover appliance types other than shutters, awnings, and blinds that are operated in a rolling way; - Revised 19.13 to allow drives to obtain a safe position; - Added 19.101 to provide a new abnormal test for drives with rated operating time; - Added 20.104.4 to establish a test intended to cover horizontal movement (non-rolling) drive parts; - Added 20.104.5 to provide an additional test to cover rolling grills to address the risk of being lifted; - Modified 22.46 and Annex R to introduce software requirements for programmable electronic circuits used to comply with Clause 20; - Added 22.101 to introduce a requirement to prevent inadvertent adjustments that would lead to unsafe application of drives; - Added examples of swing shutters and sliding shutters in Figure 101. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this standard be adopted for implementation nationally not earlier than 12 months or later than 36 months from the date

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the requirements for eaves gutters made of unplasticized poly(vinyl chloride) (PVC-U), fittings and the system intended to be used for rainwater roof drainage.
It applies to:
-   solid wall monolayer gutters;
-   solid wall multilayer gutters;
-   solid wall fittings.
The test parameters for the test methods are specified in the document.
Gutters covered by this document can be used in conjunction with fittings of acrylic materials provided these products meet the applicable requirements of this document.
NOTE 1   Products complying with this document can be used in conjunction with rainwater downpipes conforming to EN 12200-1 [1] and fixed with brackets complying with EN 1462 [2].
This document is applicable to PVC-U gutter systems of any shape with rubber seal or adhesive joints.
NOTE 2   It is the responsibility of the purchaser or specifier to make the appropriate selections from the size range and the design to take into account their particular requirements and any relevant national regulations and installation practices or codes.
NOTE 3   The term "rainwater" in this document is used also to encompass "surface water" (as defined in EN 752 [3]) run-off from buildings.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document is applicable to single and double leaf, hinged and pivoted doorsets with timber based leaves or timber framed glazed doors, covered by EN 15269-3 or EN 15269-20.
This document prescribes the methodology for extending the application of test results obtained from durability of self closing test(s) conducted in accordance with EN 1191.
Subject to the completion of the appropriate self closing test(s), the extended application can cover all or some of the following examples:
-   door leaf; pass doors;
-   glazed elements including vision panels and framed glazed doorsets;
-   side, transom and/or overpanels;
-   ventilation grilles and/or louvres;
-   wall/ceiling fixed elements (frame/suspension system);
-   glazing for door leaf, side, transom and flush over panels;
-   items of building hardware;
-   decorative finishes;
-   intumescent, smoke, draught or acoustic seals;
-   alternative supporting construction(s).

  • Standard
    78 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the test method to determine the air permeability of completely assembled windows and pedestrian door sets of any material, when exposed to positive or negative test pressures. This test method is designed to take account of conditions in use, when the window or door set is installed in accordance with the manufacturer’s specification and the requirements of relevant International Standards and codes of practice. This document does not apply to joints between the window or door frame and the building construction.

  • Standard
    14 pages
    English language
    sale 15% off

This document is applicable to single and double leaf, hinged and pivoted doorsets with timber-based leaves or timber framed glazed door leaves, covered by EN 15269-3 and / or EN 15269-20.
This document prescribes the methodology for extending the application of test results obtained from durability of self-closing test(s) conducted in accordance with EN 1191 and or EN 12605:2000, as appropriate.
Subject to the completion of the appropriate self-closing test(s), the extended application can cover all or some of the following examples:
-   door leaf; pass doors;
-   glazed doorsets including vision panels and framed glazed doorsets;
-   side, transom and/or overpanels;
-   ventilation grilles and/or louvres;
-   wall or ceiling fixed elements (door frame/suspension system);
-   glazing for door leaf, side, transom and flush over panels;
-   items of building hardware;
-   decorative finishes;
-   intumescent, strips, smoke, draught or acoustic seals;
-   alternative supporting construction(s).

  • Standard
    78 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies test method to determine the resistance to wind load of completely assembled windows and pedestrian door sets of any materials when exposed to positive or negative test pressures. This test method is designed to take account of conditions in use, when the window or door set is installed in accordance with the manufacture's specification and the requirements of relevant International Standards and codes of practice. This document does not apply to joints between the window or door frame and the building construction. This document is not intended to evaluate strength of the glass.

  • Standard
    12 pages
    English language
    sale 15% off

This document is applicable to the following types of steel based doorsets: horizontally sliding doorsets (single and double), telescopic doorsets (single and double) and single vertically sliding doorsets as covered by EN 15269 7 or EN 15269 20.
This document prescribes the methodology for extending the application of test results obtained from durability of self-closing test(s) conducted in accordance with EN 12605:2017+A1:2020 or EN 1191.
Subject to the completion of the appropriate self-closing test(s), the extended application can cover all or some of the following non-exhaustive list:
—   door leaf;
—   pass doors;
—   wall/ceiling fixed elements (frame/suspension system);
—   ventilation grilles and/or louvres;
—   glazing for door leaf;
—   items of building hardware;
—   decorative finishes;
—   intumescent, smoke, draught or acoustic seals;
—   alternative supporting construction(s).

  • Standard
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document covers steel rolling shutters as covered by EN 15269 10 or EN 15269 20.
This document prescribes the methodology for extending the application of test results obtained from durability self-closing test(s) conducted in accordance with EN 16034.
Subject to the completion of the appropriate self-closing test or tests, the extended application could cover all or some of the following non-exhaustive list:
—   shutter curtain;
—   wall/ceiling fixed elements (frame/suspension system);
—   decorative finishes;
—   intumescent, smoke, draught or acoustic seals;
—   alternative supporting construction(s).

  • Standard
    73 pages
    English language
    sale 10% off
    e-Library read for
    1 day