Source for standards, engineering specifications, manuals and technical publications

This document specifies the requirements and test methods for inspection of the use of knapsack sprayers carried on the back or shoulder of the operator for use with plant protection products (PPPs).
The requirements relate mainly to the condition of the sprayer with respect to its potential risk to the operator and the environment and its performance to achieve good application.
This document is applicable to lever-operated knapsack sprayers, knapsack compression sprayers and knapsack sprayers driven by an engine or electric motor using hydraulic pressure atomisation of the spray liquid, intended for use primarily in agriculture, forestry and horticulture, with a nominal volume of more than 6,0 l.
It does not apply to
—    knapsack combustion engine-driven air-blast sprayers, which are covered in ISO 28139:2019/Amd 1:2024,
—    controlled droplet application equipment utilizing rotary atomisers, or
—    portable application equipment for spatial application (such as foggers).

This document specifies the test suite structure (TSS) and test purposes (TP) to evaluate the conformity of on-board equipment (OBE) and roadside equipment (RSE) to ISO 13141.
It provides a basis for conformance tests for dedicated short-range communication (DSRC) equipment to support interoperability between different equipment supplied by different manufacturers.
ISO 13141 specifies requirements for the localization augmentation communication (LAC) interface level, but not for the OBE or RSE internal functional behaviour. Consequently, tests regarding OBE and RSE functional behaviour remain outside the scope of this document.

This document gives precisions on the mounting and fixing rules for testing glass products and provides guidance. It defines procedures for extended application of test results obtained in accordance with EN ISO 1716, EN ISO 11925 2, EN ISO 1182 and EN 13823 and classified according to EN 13501 1.
The extended application rules in this document are not applicable to laminated glass comprising plastic glazing sheet material.
This document is not applicable to joints and cables, junction boxes, glues, mounting seals and any fixing devices used to install the glass product.

Not available

This document specifies the safety and environmental requirements and their means of verification for the design and construction of knapsack sprayers carried on the back or shoulder of the operator for use with plant protection products. It also specifies the type of information on safe working practices (including residual risks) to be provided by the manufacturer.
This document is applicable to lever-operated knapsack sprayers, knapsack compression sprayers and knapsack sprayers driven by an engine or electric motor using hydraulic pressure atomisation of the spray liquid intended to be used primarily in agriculture, forestry and horticulture with a nominal volume of more than 6,0 l.
This document is not applicable to knapsack sprayers which are manufactured before the date of publication of this document.
It does not apply to knapsack combustion engine-driven air-blast sprayers according to ISO 28139: 2019+A1:2024.
This document deals with all significant hazards, hazardous situations and hazardous events relevant to knapsack sprayers when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex A), excepting the hazards arising from:
—     static electricity;
—     explosion or fire from chemicals for spraying; and
—     insufficient structural integrity.
Noise is not considered to be a relevant hazard for:
—     lever operated knapsack sprayers;
—     electric motor driven knapsack sprayers.
This document does not cover electromagnetic compatibility (EMC) requirements.
This document is intended to be applied in conjunction with ISO 19932-2:2025.

The main objective of this WI is to define a SIRI Passenger Real-Time Information European profile:
•   To identify a minimum subset of SIRI with codification rules and constraints for a European level plug and play exchange of real-time passenger information data between organisations at a European level
•   To reflect already existing NeTEx profiles defined at national level (Norway, France, Sweden, etc.).
•   To maintain a relevant real-time information dataset, as small and simple as possible, to ensure interoperability is maximised while at the same time enabling exchange of supplementary national real-time data that will not interfere with the core international dataset
•   To complement the EPIP (NeTEx European Passenger Information Profile) with real-time passenger information
•   To establish quality assessment procedures for implementing validation and quality assessment tools - including compliance checking rules - necessary to fulfil the requirement of the Commission
This profile will complement the NeTEx Passenger information profile and NeTEx Accessibility profile (under drafting) in order to get a set of consistent European profiles fulfilling the requirements of the Priority Action "A" of the ITS Directive.

This document specifies particular test methods for the verification of requirements of ISO 19932-1:2025 for knapsack sprayers carried on the back or shoulder of the operator for use with plant protection products.
It is applicable to lever-operated knapsack sprayers, knapsack compression sprayers and knapsack sprayers driven by an engine or electric motor using hydraulic pressure atomization of the spray liquid intended to be used primarily in agriculture, forestry and horticulture with a nominal volume of more than 6,0 l.
It does not apply to knapsack combustion engine-driven air-blast sprayers covered by ISO 28139:2019+2019A1:2024.
This document is intended to be applied in conjunction with ISO 19932-1:2025.

IEC 61643-41:2025 is applicable to devices for surge protection against indirect and direct effects of lightning or other transient overvoltages.
These devices are intended to be connected to DC power circuits and equipment rated up to 1 500 V DC. Performance and safety requirements, tests and ratings are specified in this document. These devices contain at least one nonlinear component and are intended to limit surge voltages and divert surge currents.
The test requirements provided by this document are based on the assumption that the SPD is connected to a DC power circuit fed by a power source providing a linear voltage-current characteristic. When the SPD is to be connected to a different kind of source, careful consideration is required. This mainly applies with regard to system and fault conditions to be expected in such a system (e.g. expected short circuit current, TOV-stresses).
This document can apply for railway applications, when related product standards do not exist for that area or for certain applications.
Based on a risk assessment it might not be necessary to apply all requirements of this document to SPDs designed for specific power applications only, e.g. circuits with a low power capability, circuits supplied by nonlinear sources, circuits with protective separation from the utility supply.
NOTE 1 More information on risk assessment is provided in IEC Guide 116.
SPDs for PV applications are not covered by this document.
NOTE 2 Such SPDs for PV applications are covered by IEC 61643-31.
NOTE 3 Other exclusions based on national regulations are possible.
This International Standard is to be used in conjunction with IEC 61643-01.

This document specifies the performance requirements and test methods for small steam sterilizers and sterilization cycles which are used for medical purposes or for materials that are likely to come into contact with blood or body fluids.
This document applies to automatically controlled small steam sterilizers that generate steam using electrical heaters or use steam that is generated by a system external to the sterilizer.
This document applies to small steam sterilizers used primarily for the sterilization of medical devices with a chamber volume of less than 60 l and unable to accommodate a sterilization module (300 mm × 300 mm × 600 mm).
The requirements concerning the quality management and risk management are addressed by other standards (e.g. EN ISO 13485, EN ISO 14971).
This document does not apply to small steam sterilizers that are used to sterilize liquids or pharmaceutical products.
This document does not specify safety requirements related to risks associated with the zone in which the sterilizer is used (e.g. flammable gases).
This document does not specify requirements for the validation and routine control of sterilization by moist heat.
NOTE   Requirements for the validation and routine control of sterilization by moist heat are given in EN ISO 17665.
This document does not specify requirements for other sterilization processes that also employ moist heat as part of the process (i.e. formaldehyde, ethylene oxide).

IEC 60947-5-7:2024 states the requirements for proximity devices that correspond to the scope of IEC 60947-5-2:2019 with analog output (PDAO) and/or a digital output to transmit a corresponding digital value representing the detected sensing input. These devices can provide additional parameters. This second edition cancels and replaces the first edition published in 2003. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) New structure; b) Update and expansion of definitions on analog output properties; c) Expanded performance requirements on analog output; d) Update and new normative references; e) Update of EMC requirements; f) Harmonization with IEC 62828 series; g) Harmonization with IEC 62683 and IEC 61987 definitions; h) Harmonization with IEC 61131-2 requirements; i) Update of the Annex A (former Annex G), Example of the determination of the conformity; j) New Annex B, Overview tests and influence quantities; k) New Annex C, Additional requirements for proximity switches with analog output incorporating a built-in communication interface complying with IEC 61131-9; l) New Annex D, Main characteristics for proximity devices with analog output.

This document describes the delivery of functional, economic, environmental, social, societal, cultural, intellectual and personal benefits by AI systems as perceived by their stakeholders. The document includes illustrative use cases of AI systems.

IEC 61095:2023 is available as IEC 61095:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61095:2023 applies to electromechanical air break contactors for household and similar purposes provided with main contacts intended to be connected to circuits the rated voltage of which does not exceed 440 V AC (between phases) with rated operational currents less than or equal to 63 A for utilization category AC-7a, and 32 A for utilization categories AC‑7b, AC‑7c and AC-7d (expressed in rated power), and rated conditional short-circuit current less than or equal to 6 kA. This third edition cancels and replaces the second edition published in 2009. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) addition of requirements for screwless terminals; b) addition of requirements for the switching of LED lamps. Contactors for domestic and similar applications can be used for controlling lighting loads which is increasingly using LED lamp technology. A specific category for contactors is created: AC-7d. Requirements and tests are added to cover this market development, mainly for making and breaking and conventional operational performance; c) addition of requirements for contactors with electronically controlled electromagnet. Household contactors with electronically controlled electromagnet are available for years on the market. To fully cover such device, requirements and tests are added, dealing mainly with operating limits, behaviour in abnormal conditions, breakdown of components, EMC tests, etc. d) embedded software. More and more contactors are incorporating electronic circuits with embedded software. A reference is provided to guide the design of the software.

This document specifies a method for the determination of the bulk density, apparent porosity and true porosity of dense shaped refractory products. Shaped refractories are those which have fixed geometry and dimensions when delivered to the user. This document is accordingly applicable to standard shape refractory bricks, but also special shapes refractory products and pre-cast products. This document is also applicable to unshaped refractories (see ISO 1927-6) after preparation of test specimens according to ISO 1927-5. NOTE For shaped insulating refractory products, the bulk density and true porosity are determined in accordance with ISO 5016.

This document specifies the procedure for registration of organization identification schemes, and the requirements for the administration of International Code Designator values, to designate these organization identification schemes.

This document establishes principles for and gives guidance on using a service excellence maturity model (SEMM). This document is applicable to all organizations delivering services, such as commercial organizations, manufacturing companies, public services and not-for-profit organizations. In accordance with ISO 23592, it can help organizations to determine their own maturity level with regard to service excellence. It also offers guidance for future improvements and can be used for internal and external audits. An organization can decide for itself whether the whole service excellence model with its four dimensions and nine elements or only selected dimensions and elements are assessed and improved.

This document describes approaches and methods that can be used to achieve explainability objectives of stakeholders with regard to machine learning (ML) models and artificial intelligence (AI) systems’ behaviours, outputs and results. Stakeholders include but are not limited to, academia, industry, policy makers and end users. It provides guidance concerning the applicability of the described approaches and methods to the identified objectives throughout the AI system’s life cycle, as defined in ISO/IEC 22989.

This document specifies quality measures for quantitatively measuring quality characteristics that are specified by ISO 8000-210 for use with sensor data. The following are within the scope of this document: — fundamental principles and assumptions for measuring the quality of sensor data; — quality measures for sensor data, in respect of corresponding quality characteristics and data anomalies; — requirements for using data quality characteristics and data quality measures for measuring the quality of sensor data. The following are outside the scope of this document: — analogue, image, video and audio data that are captured by sensors; — signal processing that converts or modifies analogue data to create digital data; — methods to measure and improve data quality.

This document specifies the application of dynamic light scattering (DLS) to the following: — measurement of average hydrodynamic particle size; — measurement of the size distribution of mainly sub micrometre-sized particles, emulsions or fine bubbles dispersed in liquids. This document is applicable to the measurement of a broad range of dilute and concentrated suspensions.

This document gives guidance on the application of ISO 9001:2015 in police organizations. This document can assist a police organization to demonstrate its ability to consistently provide products and services that meet expectations of interested parties as well as applicable statutory and regulatory requirements. This document can assist a police organization in the satisfaction of interested parties. This document does not provide definitive interpretations of ISO 9001. This document is applicable to police organizations of all types, sizes, maturity level service and geographic location (e.g. police stations, border crossings, correctional facilities, civil defence).