IEC/TC 61 - IEC_TC_61

IEC 60335-2-80:2015 is available as IEC 60335-2-80:2015 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. IEC 60335-2-80:2015(E) deals with the safety of electric fans for household and similar purposes, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances. Examples of fans that are within the scope of this standard are ceiling fans; duct fans; partition fans; pedestal fans and table fans. This standard also applies to separate controls supplied with fans. Appliances not intended for normal household use but which nevertheless may be a source of danger to the public, such as appliances intended to be used by laymen in shops, in light industry and on farms, are within the scope of this standard. As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by all persons in and around the home. However, in general, it does not take into account persons (including children) whose physical, sensory or mental capabilities; or lack of experience and knowledge prevents them from using the appliance safely without supervision or instruction. It also does not take into account children playing with the appliance. It was established on the basis of the fifth edition (2010) of that standard. This third edition cancels and replaces the second edition published in 2002, its Amendment 1 (2007) and its Amendment 2 (2011). It constitutes a technical revision. The principal changes in this edition as compared with the second edition of IEC 60335-2-80 are as follows (minor changes are not listed): - added definition for ceiling fan suspension system (3.102); - added instructions for ceiling fan maintenance (7.12); - added instructions for ceiling fan installation (7.12.1); - added entrapment assessment criteria for table and pedestal fan with a fan head that oscillates in the up-down direction (20.102); - added requirements for insulation of pre-installed internal wiring used to supply attached luminaires (22.101); - added suspension system failure protection requirements for ceiling fans (22.102); - added motor brush wear requirements (27.3). The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this standard be adopted for implementation nationally not earlier than 12 months or later than 36 months from the date of its publication. Key words: Fans, Duct fans, Pedestal fans, Ceiling fans, Partition fans, Table fans

IEC 60335-2-39:2012 deals with the safety of electrically operated commercial multi-purpose cooking pans not intended for household and similar use, their rated voltage being not more than 250 V for single-phase appliances connected between one phase and neutral and 480 V for other appliances. This standard also deals with pressurized appliances and appliances with pressurized parts. These appliances are used for processing food for commercial consumption, for example in kitchens of restaurants, canteens, hospitals and in commercial enterprises such as bakeries, butcheries, etc. The electrical part of appliances making use of other forms of energy is also within the scope of this standard. As far as is practicable, this standard deals with the common hazards presented by these types of appliances. Attention is drawn to the fact that for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary. The principal changes in this edition as compared with the fifth edition of IEC 60335-2-39 are as follows (minor changes are not listed): - addition to definition of portable appliances, atmospheric multi-purpose cooking and rated pressure; - deletion of equipotential symbol 5021 of IEC 60417 covered by Part 1; - addition of instructions for multi-purpose cooking pans; - modification on leakage current permissible for portable class l appliances; - addition to abnormal test requirements; - addition to mechanical hazard test for multi-purpose cooking pans; - addition of construction test for multi-purpose cooking pans; - addition to construction requirements for lids and theirs grips; - addition to construction requirements for positioning of pressure reliefs; - addition to construction's fixed appliances which are moved forward and backward for cleaning purposes.
The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months or later than 36 months from the date of publication. Keywords: Multi-purpose cooking pans.

NEW!IEC 60335-2-86:2018 is available as IEC 60335-2-86:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60335-2-86:2018 deals with the safety of electric fishing machines by means of which water may be electrified for the purpose of catching fish or for providing barriers to all animals living in water. The rated voltage of electric fishing machines is not more than 250 V for single phase machines and 480 V for other machines, except that the rated voltage of electric fishing machines for permanent connection to fixed wiring is not more than 1 000 V. Electric fishing machines are appliances for scientific and commercial use. Additional requirements for boat mounted electric fishing machines are given in Annex AA. This Part 2 is to be used in conjunction with the latest edition of IEC 60335-1 and its amendments. It was established on the basis of the fifth edition (2010) of that standard. This third edition cancels and replaces the second edition published in 2002, its Amendment 1 (2005) and its Amendment 2 (2012). This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - aligns the text with IEC 60335-1, Ed 5, and its Amendments 1 and 2; - some notes have been converted to normative text (22.102, 22.113, 26.106); - requirements for battery-operated electric fishing machines have been moved to Annex S.

The contents of the corrigendum of March 2017 have been included in this copy.

2022-01-26: The PR will be put on hold to await the AM11. Then the standard will be sent to CCMC for publication together with AM2 and AM11. The standard will be offered for LVD OJ listing.
NEXT ACTION: TB ACTION by 2021-01-31 (TC to send text after drop of voting results - D167/C064)
PART OF A PACKAGE -- 2020-07-27: Common modifications to this EN IEC are included in prAA (PR=72426) to be accepted by BT by 2020-09-22
HAS NAC ASSESSMENT BY 2019-09-03 - negative assessment
2017-03-28: publication on the hold due to missing Annex ZZ (pending on Annex for Part 1) - D156/C084: TC to explain

NEXT ACTION: TB ACTION by 2021-01-31 (TC to send text after drop of voting results - D167/C064)
HAS ASSESSMENT BY 2019-09-27
2019-01-23 CV: blocked until ratification of pr64193 is completed

IEC 60335-2-103:2015(E) deals with the safety of electric drives for horizontally and vertically moving gates, doors, garage doors and windows for household and similar purposes, their rated voltage being not more than 250 V for single-phase drives and 480 V for other drives. It also covers the hazards associated with the movement of the driven part. Battery-operated drives and other d.c. supplied drives are within the scope of this standard. Dual supply drives, either mains-supplied or battery-operated, are regarded as battery-operated drives when operated in the battery mode. Drives not intended for normal household use but which nevertheless may be a source of danger to the public, such as drives intended to be used by laymen in shops, offices, hotels, restaurants, hospitals, in industry and on farms, are within the scope of this standard. Requirements for drives for doors that may be used in emergency routes and exits are given in Annex AA. Examples of drives within the scope of this standard are drives for: - folding doors; - revolving doors; - rolling doors; - roof windows; - sectional overhead doors; - swinging and sliding gates or doors. As far as is practicable, this standard deals with the common hazards presented by drives that are encountered by all persons in and around the home. However, in general, it does not take into account persons (including children) whose physical, sensory or mental capabilities; or lack of experience and knowledge prevents them from using the drive safely without supervision or instruction or children playing with the drive. It was established on the basis of the fifth edition (2010) of that standard. This third edition cancels and replaces the second edition published in 2006 and its Amendment 1 (2010). It constitutes a technical revision. The principal changes in this edition as compared with the second edition of IEC 60335-2-103 are as follows (minor changes are not listed): modification of requirements in Clause 20 by introduction of new annexes. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this standard be adopted for implementation nationally not earlier than 12 months or later than 36 months from the date of its publication. Key words: Drives, Gates, Doors, Windows.

IEC 60335-2-97:2016 deals with the safety of electric drives for shutters, blinds and awnings, intended for household and similar purposes, their rated voltage being not more than 250 V for single-phase drives and 480 V for other drives. Battery-operated drives and other d.c. supplied drives are within the scope of this standard. Examples of equipment that can be driven are: - spring controlled folding arm awnings; - curtains; - grilles covering doors and windows; - projection screens; - shutters covering doors and windows and draperies. Drives may be supplied with a driven part. Drives not intended for normal household use but that nevertheless may be a source of danger to the public, such as drives intended to be used by laymen in shops, in light industry, on farms and on industrial premises, are within the scope of this standard. Attention is drawn to the fact that for drives intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary. This standard does not apply to - drives intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas); - drives for vertically moving garage doors for residential use (IEC 60335-2-95); - drives for rolling doors (IEC 60335-2-103); - drives used in premises such as hangars or in heavy industry and drives for theatre curtains. As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by all persons in and around the home. However, in general, it does not take into account: - persons (including children) whose physical, sensory or mental capabilities or lack of experience and knowledge prevents them from using the appliance safely without supervision or instruction or - children playing with the appliance. This third edition cancels and replaces the second edition published in 2002 including its Amendment 1 (2004) and its Amendment 2 (2008). It constitutes a technical revision. The principal changes in this edition as compared with the second edition of IEC 60335-2-97 are as follows (minor changes are not listed): - Deleted "rolling" from the title and modified the scope to cover appliance types other than shutters, awnings, and blinds that are operated in a rolling way; - Revised 19.13 to allow drives to obtain a safe position; - Added 19.101 to provide a new abnormal test for drives with rated operating time; - Added 20.104.4 to establish a test intended to cover horizontal movement (non-rolling) drive parts; - Added 20.104.5 to provide an additional test to cover rolling grills to address the risk of being lifted; - Modified 22.46 and Annex R to introduce software requirements for programmable electronic circuits used to comply with Clause 20; - Added 22.101 to introduce a requirement to prevent inadvertent adjustments that would lead to unsafe application of drives; - Added examples of swing shutters and sliding shutters in Figure 101. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this standard be adopted for implementation nationally not earlier than 12 months or later than 36 months from the date

IEC 60335-2-71:2018 deals with the safety of all kinds of electrical heating appliances used for livestock rearing and breeding, such as: heat-radiating appliances, electrical sitting-hens, incubators, chicken breeding units and heating plates for animals, the rated voltage of the appliances being not more than 250 V for single-phase appliances and 480 V for other appliances. This standard applies to heating appliances used for livestock rearing and breeding that include an electrical motor. This standard does not apply to: - appliances designed exclusively for industrial purposes; - appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas); - heating units embedded in the floor; - flexible sheet heating elements for room heating (IEC 60335-2-96); - room heaters (IEC 60335-2-30). This third edition cancels and replaces the second edition published in 2002, its Amendment 1 (2007) and its Amendment 2 (2012). This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - two paragraphs are deleted (Introduction); - normative references updated (Clause 2); - colour required for symbols (7.6); - some notes converted to normative text (19.2, 21.101, 22.104).

NEXT ACTION: UNDER BT CONSULTATION, CLOSING ON 2019-09-17
HAS&EY ACTION BY 2019-06-17: assessement expected by 2019-06-17
CCM ACTION BY 2019-04-30 (request post-factum assessment) - done
2018-12-07 SW: Waiting for annex ZZ to be added to the publication by BT decision after positive assessment.2017-05-03: D156/C084 - Ratified standards not being made available.
2017-04-20 OD: Publication on hold, No TC reply to proofing

NEXT ACTION: UNDER BT CONSULTATION, CLOSING ON 2019-09-03
HAS CONSULTANT ASSESSMENT BY 2019-05-21
2019-04-16 CV:  Assessment for MD requested on 2019-04-16 (dd: 2019-05-21). If positively assessed, finalization will be brought to BT
2019-03-19 CV: Positively assessed by LVD Consultant and finalization of project brought to BT but consultation failed (Members want to have the project linked to the MD as well)
2019-01-23 CV: Revised Annex ZZ positively assessed and to be circulated to BT
2018-09-14 CV: Revised assessment requested on 2018-09-14 (deadline E&Y: 2018-10-19)
20170202OD: Document pending publication, waiting for annex ZZ

Deals with the safety of electric animal-stunning equipment, These are for inductrial or commercial use, on farms or in areas where they may be a source of danger to the public. The standard covers manual, semi-automatic and automatic equipment. For electric fence energizers, see EN 60335-2-76. For electric fishing machines, see EN 60335-2-86.

NEW!IEC 60335-2-102:2017 is available as IEC 60335-2-102:2017 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60335-2-102:2017 deals with the safety of gas, oil and solid-fuel burning appliances having electrical connections, for household and similar purposes, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances. This standard covers the electrical safety and some other safety aspects of these appliances. All safety aspects are covered when the appliance also complies with the relevant standard for the fuel-burning appliance. If the appliance incorporates electric heating sources, safety aspects concerning these electric sources are covered when the appliance also complies with the relevant part 2 of IEC 60335. Examples of appliances within the scope of this standard are – central heating boilers; – commercial catering equipment; – cooking appliances; – laundry and cleaning appliances; – room heaters; – warm air heaters; – water heaters. Appliances not intended for normal household use but which nevertheless may be a source of danger to the public, such as appliances intended to be used by laymen in shops, in light industry and on farms, are within the scope of this standard. This standard deals with the reasonably foreseeable hazards presented by appliances that are encountered by all persons. However, in general, it does not take into account – persons (including children) whose • physical, sensory or mental capabilities; or • lack of experience and knowledge prevents them from using the appliance safely without supervision or instruction; – children playing with the appliance. Attention is drawn to the fact that – for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary; This standard does not apply to – appliances intended exclusively for industrial purposes; – appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas). This second edition cancels and replaces the first edition published in 2004 including its Amendment 1 (2008) and its Amendment 2 (2012). This edition constitutes constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a spillage test is introduced for appliances that have a flat surface on which a cup may be placed (15.101); terms and definitions were renumbered and some notes have been converted to normative text or deleted (19.11.2, 22.103). This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. This part 2-102 is to be used in conjunction with the latest edition of IEC 60335-1 and its amendments. It was established on the basis of IEC 60335-1:2010, its Amendment 1:2013 and its Amendment 2:2016. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of

IEC 60335-2-81:2015 deals with the safety of electric foot warmers and heating mats for household and similar purposes, their rated voltage being not more than 250 V. Appliances not intended for normal household use but which nevertheless may be a source of danger to the public, such as appliances intended to be used by laymen in shops, in light industry and on farms, are within the scope of this standard. As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by all persons in and around the home. However, in general, it does not take into account persons (including children) whose physical, sensory or mental capabilities; or lack of experience and knowledge prevents them from using the appliance safely without supervision or instruction. It also does not take into account children playing with the appliance. It was established on the basis of the fifth edition (2010) of that standard. This third edition cancels and replaces the second edition published in 2002, its Amendment 1 (2007) and its Amendment 2 (2011). It constitutes a technical revision. The principal changes in this edition as compared with the second edition of IEC 60335-2-81 are as follows (minor changes are not listed): - requirements for washable appliances (5.3, 7.1, 7.6, 7.12); - requirements for controls in flexible cords (15.1.1, 24.2) and requirements for appliance inlets (22.105, 24.1.5, 29.1.3). The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this standard be adopted for implementation nationally not earlier than 12 months or later than 36 months from the date of its publication. Key words: Foot warmer, heating element, heating mat

IEC 60335-2-111:2015 deals with the safety of electric ondol-mattresses for household and similar purposes, their rated voltage being not more than 250 V. This standard also applies to control units supplied with the appliance. Appliances not intended for normal household use but which nevertheless may be a source of danger to the public, such as appliances intended to be used in community spas or by persons in cold ambient temperatures, are within the scope of this standard. As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by all persons in and around the home. However, in general, it does not take into account the use of appliances by young children or infirm persons without supervision or children playing with the appliance. It was established on the basis of the fifth edition (2010) of that standard. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this standard be adopted for implementation nationally not earlier than 12 months or later than 36 months from the date of its publication. Key words: ondol mattress, heating element, non-flexible heated part This publication is to be read in conjunction with IEC 60335-1:2013.

2018-11-10 AAP: Waiting for assessment from LVD consultant.

2016-11-08: Voting results dropped (D155/C035)

NEXT ACTION: UNDER BT CONSULTATION CLOSING ON 2019-09-03
NEXT ACTION: HAS CONSULTANT ASSESSMENT BY 2019-05-21
2019-04-16 CV:  Assessment for MD requested on 2019-04-16 (dd: 2019-05-21). If positively assessed, finalization will be brought to BT
2019-03-19 CV: Positively assessed by LVD Consultant and finalization of project brought to BT but consultation failed (Members want to have the project linked to the MD as well)
2018-09-14 CV: Revised assessment requested on 2018-09-14 (deadline E&Y: 2018-10-19)
2017-07-31 - Cannot allocate for publication due to missing assessment from Consultant.

NEXT ACTION: UNDER BT CONSULTATION CLOSING ON 2019-09-03
NEXT ACTION: HAS CONSULTANT ASSESSMENT BY 2019-05-21
2019-04-16 CV:  Assessment for MD requested on 2019-04-16 (dd: 2019-05-21). If positively assessed, finalization will be brought to BT
2019-03-19 CV: Positively assessed by LVD Consultant and finalization of project brought to BT but consultation failed (Members want to have the project linked to the MD as well)
2018-09-14 CV: Revised assessment requested on 2018-09-14 (deadline E&Y: 2018-10-19)
2017-05-16 - Cannot allocate for publication due to negative assessment from Consultant.

NEXT ACTION: UNDER BT CONSULTATION CLOSING on 2019-09-03
NEXT ACTION: HAS CONSULTANT ASSESSMENT BY 2019-05-21
2019-04-16 CV:  Assessment for MD requested on 2019-04-16 (dd: 2019-05-21). If positively assessed, finalization will be brought to BT
2019-03-19 CV: Positively assessed by LVD Consultant and finalization of project brought to BT but consultation failed (Members want to have the project linked to the MD as well)
2018-09-14 CV: Revised assessment requested on 2018-09-14 (deadline E&Y: 2018-10-19)
2017-05-02 - Cannot allocate for publication due to negative assessment from consultants

2022-05-04: BT agreed to temporarily remove the link to LVD & MD  (D172/C018)
2022-05-03: The link to LVD and MD is removed temporarily (D172/C018)
PART OF A PACKAGE (with PR=61447) -- HAS CONSULTANT ASSESSMENT BY 2020-03-02
FprAA to be circulated to cover Common Modifications (see PR=25306)

2018-10-16 CV: Positive assessment from NAC received  -- BT doc (requesting publication incl. Annex ZZ) to be circulated.
2018-08-12 CV: New assessment requested
2017-05-02: D156/C084 - Ratified standards not being made available.
2017-03-28: publication on the hold due to missing Annex ZZ (pending on Annex for Part 1) - D156/C084: TC to explain

2018-10-01: Positive assessment from NAC received on 2018-10-01. BT doc prepared and to be submitted to 4 weeks consultation
2018-09-14 CV: Positive assessment expected (info from NAC) but not yet uploaded on HAS Livelink folder -- BT doc for publication awaiting official assessment
2018-08-12 CV: New assessment requested

2018-12-06: BTdecision D161/C047: project can proceed and be finalized (without link to legislation)

TC 61 advise on 2016-02-01: Common modifications needed but experts on these products not yet detected and not declared their availability to prepare a suitable proposal

2018-12-06: BT decision D161/C048: BT agreed to remove link to Machinery Directive (2006/42/EC) and to proceed to finalization and publication
2017-07-18 - Cannot allocate for publication due to negative assessment from Consultant.

2018-12-06: BT decision D161/C048: BT agreed to remove link to Machinery Directive (2006/42/EC) and to proceed to finalization and publication
2017-11-21 - Negative assessment is received during CDV stage. Consultant assessment request is missing for FDIS.

IEC 60335-2-82:2017(E) deals with the safety of electric commercial amusement machines and personal service machines, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances. Examples of appliances that are within the scope of this standard are: amusement machines; tables; bowling machines; dartboards; driving simulators; gaming machines; kiddie rides; laser shooting appliances; pinball machines; video games; personal service machines; card re-value machines; currency dispensers; luggage lockers; weighing machines; shoe shining appliances. As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by users and maintenance persons. For appliances intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary; This standard does not apply to appliances intended exclusively for household use; appliances intended exclusively for industrial purposes; appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas); appliances for washing cars; dispensing appliances and vending machines (IEC 60335-2-75); appliances within the scope of IEC 60065, such as jukeboxes and household video games; appliances within the scope of IEC 60950-1, such as copying machines, ticket machines and automatic teller machines; appliances intended to be used when a trained attendant is present, such as virtual reality systems; equipment intended exclusively for fairgrounds, such as carousels; self-balancing personal transport devices. This third edition cancels and replaces the second edition published in 2002 including its Amendment 1 (2008) and its Amendment 2 (2015). This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - It is clarified that 22.44 is not applicable to amusement machines; - Modified some Notes to make them normative text (5.6, 11.2, 11.8, 15.2.101, 15.2.102, 15.2.104, 15.3, 19.4, 19.101, 24.101, 24.102) and - Reference to 22.106 is made in Annex R. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. This part 2-82 is to be used in conjunction with the latest edition of IEC 60335-1 and its amendments. It was established on the basis of IEC 60335-1:2010, its Amendment 1:2013 and its Amendment 2:2016. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months or later than 36 months from the date of publication. Key words: Amusement Machines, Personal Service Machines, Safety

IEC 62115:2017 specifies safety requirements for electric toys that have at least one function dependant on electricity, electric toys being any product designed or intended, whether or not exclusively, for use in play by children under 14 years of age. Examples of electric toys also within the scope of this standard are: - constructional sets; - experimental sets; - functional electric toys (an electric toy that performs and is used in the same way as a product, appliance or installation intended for use by adults, and which may be a scale model of such product, appliance or installation); - electric toy computers as well as a doll's house having an interior lamp. If the packaging is intended to have play value then it is considered to be part of the electric toy. This International Standard only covers the safety aspects of electric toys that relate to an electrical function. This standard covers the safety of electric toys taking power from any source, such as batteries, transformers, solar cells and inductive connections. This second edition cancels and replaces the first edition published in 2003, Amendment 1 (2004) and Amendment 2 (2010). This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - the general conditions for tests has been rewritten and modified (Clause 5); - the criteria for reduced testing has been modified (Clause 6); - warnings for toys using button batteries or coin batteries have been added (7.3.3.2, 7.3.3.3); - warnings on ride-on toys have been added (7.5); - the requirements concerning accessibility of batteries have been updated (13.4.1 and 13.4.2); - added requirements to cover toys placed above a child (13.4.4); - added requirements to cover toys connected to other equipment (13.9); - modified the requirements for safety of toys incorporating optical radiation sources (Annex E), to include requirements for using the technical LED data sheet for checking compliance with the specified accessible emission limits (AEL); - updated the details for measurements of the optical radiation from the toy (Annex E); - introduced an informative Annex I concerning measurement methods for toys with an integrated field source generating EMF; - included a normative Annex J concerning safety of remote-controls for electric ride-on toys. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months or later than 36 months from the date of its publication. Key words: Safety, Electric Toys

IEC 60335-2-105:2016 deals with the safety of electric multifunctional shower cabinets and electric separate multifunctional shower units for household and similar purposes, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances. Appliances not intended for normal household use but which nevertheless may be a source of danger to the public, such as appliances intended to be used by laymen in hotels, fitness centres and similar locations, are within the scope of this standard. This standard deals with the reasonably foreseeable hazards presented by appliances that are encountered by all persons. However, in general, it does not take into account persons (including children) whose physical, sensory or mental capabilities; or lack of experience and knowledge prevents them from using the appliance safely without supervision or instruction; children playing with the appliance. This second edition cancels and replaces the first edition published in 2004 including its Amendment 1 (2008) and its Amendment 2 (2013). It constitutes a technical revision. The principal changes in this edition as compared with the first edition of IEC 60335-2-105 are as follows: - revised the application of a live part (8.1.4); - aligned the temperature rise limits of surfaces likely to be in contact with the skin with IEC Guide 117 for a contact time of one minute (Table 3). This publication is to be read in conjunction with IEC 60335-1:2010. It was established on the basis of the fifth edition (2010) of that standard. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months or later than 36 months from the date of its publication. Key words: Shower, Shower cabinets, Multifunctional

IEC 60335-2-29:2016 is available as IEC 60335-2-29:2016 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. IEC 60335-2-29:2016 deals with the safety of electric battery chargers for household and similar use having an output not exceeding 120 V ripple-free direct current, their rated voltage being not more than 250 V. Battery chargers intended for charging batteries in a household end use application outside the scope of the IEC 60335 series of standards are within the scope of this standard. Requirements for battery chargers for use by children at least 8 years old without supervision are given in Annex AA. Battery chargers not intended for normal household use, but which nevertheless may be a source of danger to the public, such as battery chargers intended for use in garages, shops, light industry and on farms, are within the scope of this standard. As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by all persons in and around the home. However, in general, it does not take into account persons (including children) whose physical, sensory or mental capabilities; or lack of experience and knowledge prevents them from using the appliance safely without supervision or instruction; children playing with the appliance. This standard does not apply to built-in: - battery chargers, except those for installing in caravans and similar vehicles; - battery chargers that are part of an appliance, the battery of which is not accessible to the user; - battery chargers intended exclusively for industrial purposes; - battery chargers intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas); - battery chargers for emergency lighting or supply units for electronic equipment. This fifth edition cancels and replaces the fourth edition published in 2002 including its Amendment 1 (2004) and its Amendment 2 (2009). It constitutes a technical revision. The principal changes in this edition as compared with the fourth edition of IEC 60335-2-29 are as follows (minor changes are not listed): - Revised the drop test to refer to IEC 60068-2-31 (21.101); - Requirements for supply cords on battery chargers used at low temperatures (25.7); - Requirements for battery chargers having an output voltage exceeding SELV have been added (1, 3.2.2, 3.4.3, 10.101, 24.4, 25.5, 25.7, 25.8, 25.15. 26.5); - A classification for battery chargers used outdoors has been added (6.2, 29.2) and some notes in Clause 1, Subclauses 7.1 and 22.102, Figure 101 and Annex AA 11.8 have been converted to normative text. It was established on the basis of the fifth edition (2010) of that standard. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this standard be adopted for implementation nationally not earlier than 12 months or later than 36 months from the date of its publication. Key words: Battery, Battery Charger This publication is to be read in conjunction with IEC 60335-1:2010.

IEC 60335-2-110:2013 deals with the safety of microwave appliances intended for commercial use, their rated voltage being not more than 250 V for single-phase appliances connected between one phase and neutral and 480 V for other appliances. Appliances covered by this standard incorporate an open-ended applicator (as example an overview is given in Figure 103) for treatment of the load. They are divided into three types: - with insertion applicator, typically for moisture removal by insertion into holes in floors, walls or ceilings (an example is given in Figure 106); - with large area contacting applicator, typically for drying of floors, walls or ceilings (examples are given in Figure 104 and Figure 105); - with small area contacting applicator, typically for paint removal and spot-heating (an example is given in Figure 107). Key words: commercial microwave appliance, insertion applicator, contacting applicator

IEC 60335-2-90:2015(E) deals with - the safety of microwave ovens with a cavity door intended for commercial use, their rated voltage being not more than 250 V for single-phase appliances connected between one phase and neutral and 480 V for other appliances; - the safety of combination microwave ovens with a cavity door, the requirements for which are contained in Annex AA; - the safety of microwave ovens without a cavity door and with transportation means that are intended for commercial use only, for the heating of food and beverages, the requirements for which are contained in Annex BB. Microwave ovens covered by Annex BB have transportation means for moving the load through the microwave oven. Requirements for tunnel microwave ovens and several types of microwave vending machines are covered. This standard also deals with microwave ovens intended to be used on board ships, for which Annex EE is applicable. In general, this standard does not take into account the use of appliances by young children or infirm persons without supervision or children playing with the appliance. This international standard does not take into account the use of a microwave oven without a cavity door and with transportation means by ordinary persons except in the vicinity of entrance and exit ports. This part 2 is to be used in conjunction with the latest edition of IEC 60335-1 and its amendments. It was established on the basis of the fifth edition (2010) of that standard. This fourth edition cancels and replaces the third edition published in 2006 including its Amendment 1 (2010) and Amendment 2 (2014). It constitutes a technical revision. The principal changes with respect to the previous edition are as follows (minor and editorial changes are not listed): - a statement in 7.12 is required for appliances intended to be used on commercial road vehicles; - a statement in 7.12 is required concerning cleaning of the appliance with a water jet; - the replacement of 22.103, 22.104 and 22.105 allows interlock systems with at least one concealed door interlock as well as alternative interlock systems without concealed door interlock; - requirements are added for appliances for installation in commercial road vehicles; - an annex is added dealing with routine tests. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this standard be adopted for implementation nationally not earlier than 12 months or later than 36 months from the date of its publication. Key words: Microwave, Microwave Oven, Microwave enclosure

The contents of the corrigendum of September 2016 have been included in this copy.

2022-07-08: Offering for MD can be followed up after publication of A16.
TB ACTION BY 2019-04-30 (confirmation skipping vote of pr64193)
2018-10-05 - MAH: blocked until ratification of pr64193 is completed
2016-11-08: Voting results dropped (D155/C035)
2017-08-03: ON HOLD, TC will deliver new text

IEC 60335-2-75:2012 deals with the safety of electric commercial dispensing appliances and vending machines for preparation or delivery of food, drinks and consumer products, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances. Examples of appliances that are within the scope of this standard are bulk tea or coffee brewing machines, cigarette vending machines, coffee grinders, commercial liquid heaters, coffee makers with or without integrated coffee grinder, coffee makers with cooling systems, hot and cold beverage vending machines, hot water dispensers, ice cream and whipped cream dispensers, ice dispensers, newspaper, audio or video tape or disc vending machines, packaged food and drink vending machines and refrigerated merchandisers. Appliances can have more than one function. Other standards may be applicable for some functions such as refrigeration (IEC 60335-2-24) and heating by microwaves (IEC 60335-2-25). This standard also deals with the hygiene aspects of appliances. As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by users and maintenance persons. However, in general, it does not take into account young children playing with the appliance. This third edition cancels and replaces the second edition published in 2002 including its Amendment 1 (2004) and its Amendment 2 (2008). It constitutes a technical revision. The principal changes in this edition as compared with the second edition of IEC 60335-2-75 are as follows: some notes have been deleted or converted to normative text (5.2, 5.6, 5.104, 7.12.1, 7.12.101.1, 11.2, 11.8, 15.2.103, 15.2.104, 15.2.106, 15.2.109, 15.2.111, 19.102, 19.6, 19.13, 19.101, 22.6, 22.7, 22.112, 22.113, 22.114, 24.102, 27.2), added requirements for espresso coffee makers in 3.115, 22.114 and throughout standard, modified 11.4 to address heating appliances with electronic process controls and 11.6 to address combined appliances without electronic process controls, modified Clause 22 to indicate that pressure regulating devices are to be rendered inoperable and deleted ISO 13732-1 from Bibliography. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months or later than 36 months from the date of publication. Keywords: Vending machines, Dispensers.

NEXT ACTION: TB ACTION (provide next text) BY 2020-06-30
CLC/BT consultation by correspondence (to skip the vote): D165/C127 (April 2020)
2019-01-23 CV: blocked until ratification of pr64193 is completed
2017-05-02: D156/C084 - Ratified standards not being made available.
2016-01: Publication on the hold as the mother standard EN 60335-2-75:201X (pr=23927) is not published yet.

IEC 60335-2-21:2012 deals with the safety of electric storage water heaters for household and similar purposes and intended for heating water below boiling temperature, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances. Appliances not intended for normal household use but which nevertheless may be a source of danger to the public, such as appliances intended to be used by laymen in shops, in light industry and on farms, are within the scope of this standard. This standard is also applicable to immersion heater units intended to be retrofitted in a heat exchange closed water heater having provision for retrofitting. Such a unit shall comply with the requirements in Annex AA. As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by all persons in and around the home. However, in general, it does not take into account persons (including children) whose physical, sensory or mental capabilities, or lack of experience and knowledge prevents them from using the appliance safely without supervision or instruction or children playing with the appliance. This sixth edition cancels and replaces the fifth edition published in 2002 including its Amendment 1 (2004) and its Amendment 2 (2008). The principal changes in this edition as compared with the fifth edition of IEC 60335-2-21 are as follows: - added requirements for immersion heater units (fixed immersion heaters); - removed reference to ISO 13732-1 from Bibliography. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months or later than 36 months from the date of publication. Keywords: Storage, Immersion, Water, Heater

This International Standard deals with the safety of powered automatic floor treatment machines intended for commercial use indoors for the following applications: - sweeping, - scrubbing, - wet or dry pick-up, - polishing, - application of wax, sealing products and powder-based detergents, - shampooing of floors. The requirements given by this standard are applied in addition to the requirements for commercial floor treatment machines in IEC 60335-2-72, as far as applicable, and mentioned in the relevant clauses. Automatic floor treatment machines solely designed for wet or dry pick-up, additional or modified requirements of IEC 60335-2-69 where stated shall be applicable. Machines covered by this Standard may operate in automatic or manual mode. Modified requirements are given in specific sections of this standard for automatic floor treatment machines not equipped with a manual mode. The automatic floor treatment machines covered by this standard are designed to avoid hazardous contact with persons in the environment applied. It is recognized that automatic floor treatment machines for commercial use might require operation within close proximity to large groups of people, such as in shopping malls and schools. Throughout this standard, the term “machine” is used to refer to an automatic floor treatment machine The following power systems are covered: - rechargeable batteries that are recharged by built-in battery chargers or off-board battery chargers which may be incorporated within the circuitry of the machine, or mounted on the machine and incorporated within the enclosure of the automatic floor treatment machine; or powered by batteries that need to be removed to be recharged with a charger that is external to the machine, - Other systems are under consideration. This standard does not apply to - battery chargers (IEC 60335-2-29); - floor treatment appliances and wet scrubbing machines for household use (IEC 60335-2- 82 10); - floor treatment machines for commercial use (IEC 60335-2-67); - spray extraction machines for commercial use (IEC 60335-2-68); - road sweepers; NOTE 101 In Europe, the EN 17106 series covers road sweepers. - machines designed for use on slopes with a gradient exceeding 20 %; - machines equipped with 88 a power take-off (PTO); - machines designed for use in corrosive or explosive environments (dust, vapour or gas); - machines designed for use in vehicles or on board of ships or aircraft. - vacuum cleaners and water-suction cleaning appliances and automatic battery-operated cleaners for household use (IEC 60335-2-2); - vacuum cleaners designed for pickup of combustible dust; - hand-held mains-operated electrical garden blowers, vacuums and blower vacuums (IEC 60335-2-100); - Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery (IEC 60745 series, IEC 61029 series, IEC 62841 series); - appliances for medical purposes (IEC 60601-1); - robots and robotic devices: Safety requirements of personal care robots (ISO 13482) - machines with parts that extend beyond the contact zone of the machine NOTE 102 Components of the machine that operate outside the contact zone can be evaluated differently. - machines designed for picking up liquids with a flash point below 55 °C; NOTE 103 The flash point temperature limit may vary in different countries. National regulations will need to be taken into account. NOTE 104 Attention is drawn to the fact that in many countries additional requirements on the safe use of the equipment covered can be specified by the national health authorities, the national authorities responsible for the protection of labour, the national water supply authorities and similar authorities;

IEC 60335-2-43:2017(E) deals with the safety of electric clothes dryers for drying textiles on racks located in a warm airflow, clothes dryers intended for drying footwear or gloves and to electric towel rails, for household and similar purposes, their rated voltage being not more than 250 V. The clothes racks can be fixed or free-standing in a cabinet. The air circulation can be natural or forced. Appliances not intended for normal household use but that nevertheless may be a source of danger to the public, such as appliances intended to be used by laymen in shops, in light industry and on farms, are within the scope of this standard. As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by all persons in and around the home. However, in general, it does not take into account persons (including children) whose physical, sensory or mental capabilities or lack of experience and knowledge prevents them from using the appliance safely without supervision or instruction or children playing with the appliance. Attention is drawn to the fact that for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary. This standard does not apply to spin extractors (IEC 60335-2-4): - tumble dryers (IEC 60335-2-11); - appliances intended exclusively for industrial purposes or appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas). This fourth edition cancels and replaces the third edition published in 2002 including its Amendment 1 (2005) and its Amendment 2 (2008). This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: requirements for clothes dryers intended for drying footwear or gloves have been introduced (1, 3.1.9, 6.2, 11.8, 19.1, 19.13, 19.101, 19.102, 22.40, 23.3). This part 2 is to be used in conjunction with the latest edition of IEC 60335-1 and its amendments. It was established on the basis of the fifth edition (2010) of that standard. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months or later than 36 months from the date of its publication.

NEXT ACTION: UNDER BT CONSULTATION (for finalization), CLOSING ON 2020-02-18
HAS CONSULTANT ASSESSMENT (LVD) BY 2020-01-08
2017-10-16: Publication on hold due to missing Annex ZZ & assessment

2020-01-08 CV: BT decision (D164/C117) to proceed to finalization
2018-10-16 CV: Positive assessment from NAC received  -- BT doc (requesting publication incl. Annex ZZ) to be circulated.
2018-08-12 CV: New assessment requested

NEXT ACTION: PART OF A PACKAGE
2018-10-01: Positive assessment from NAC received on 2018-10-01. BT doc prepared and to be submitted to 4 weeks consultation
2018-09-14 CV: Positive assessment expected (info from NAC) but not yet uploaded on HAS Livelink folder -- BT doc for publication awaiting official assessment
2018-09-06 CV: New request for assessment sent on 2018-08-12 -- EN 60335-2-6:2015/FprA1 (PR=63514) and EN 60335-2-6:2015/FprAA (PR=62259) have been voted upon without Annex ZZ. The projects could not proceed. CLC/TC 61 worked on the Annex ZZ which, if positively assessed by the LVD consultant will be added to EN 60335-2-6:2015/FprAA (PR=62259).
If both positively assessed, EN 60335-2-6:2015/FprA1 (PR=63514) and EN 60335-2-6:2015/FprAA (PR=62259) will be published on the same date.
2018-06-25: Consultant's assessment is missing at CDV stage.

The contents of the Interpretation sheet of March 2018 have been included in this copy.

2020-08-24 CV: Not cited under LVD yet - EC waiting for clarification following a UK authority request (clarification to be provided in A11 -- PR= 63760 at ratitication stage)