Safety requirements for electrical equipment for measurement, control and laboratory use - Part 2-202: Particular requirements for electrically operated valve actuators (IEC 61010-2-202:2016)

This part of IEC 61010 specifies the safety requirements for electric ACTUATORs and
SOLENOIDs, as applied to valves, intended to be installed in an industrial process or discrete
control environment.
This part of IEC 61010 specifies:
– particular safety requirements for general purpose electrically operated valve ACTUATORs
and SOLENOIDs,
– related verification tests.
The general purpose electrically operated valve ACTUATORs and SOLENOIDs, covered by this
part of IEC 61010 are limited to:
– those rated 600 V alternative current/ 840 V direct current or less,
Service personnel interface to equipment included in the scope of this document.

Sicherheitsbestimmungen für elektrische Mess-, Steuer-, Regel- und Laborgeräte - Teil 2-202: Besondere Anforderungen für elektrisch betriebene Ventile und Stellantriebe (IEC 61010-2-202:2016)

Règles de sécurité pour appareils électriques de mesurage, de régulation et de laboratoire - Partie 2-202: Exigences particulières pour les actionneurs à vanne à commande électrique (IEC 61010-2-202:2016)

L'IEC 61010-2-202:2016 spécifie les exigences de sécurité relatives aux ACTIONNEURs et SOLENOÏDEs électriques, telles qu'appliquées aux vannes destinées à être installées dans un processus industriel ou dans un environnement de commande discret. Cette publication doit être lue conjointement avec la IEC 61010-1:2010

Varnostne zahteve za električno opremo za meritve, nadzor in laboratorijsko uporabo - 2-202. del: Posebne zahteve za električni pogon ventilov (IEC 61010-2-202:2016)

Ta del standarda IEC 61010 določa varnostne zahteve za električna SPROŽILA in ELEKTROMAGNETE, ki se uporabljajo za ventile, namenjene inštalaciji v industrijskih procesih ali diskretnih kontrolnih okoljih.
Ta del standarda IEC 61010 določa:
– posebne varnostne zahteve za električna SPROŽILA in ELEKTROMAGNETE za splošni namen,
– povezane preskuse.
Električna SPROŽILA in ELEKTROMAGNETI za splošni namen, ki so zajeti v tem delu standarda IEC 61010, so omejeni na:
– tiste z nazivno napetostjo 600 V za izmenični tok/840 V za enosmerni tok ali manj.
Vmesnik opreme za servisno osebje spada na področje uporabe tega dokumenta.

General Information

Status
Published
Publication Date
07-Aug-2017
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
08-May-2017
Due Date
13-Jul-2017
Completion Date
08-Aug-2017

RELATIONS

Buy Standard

Standard
SIST EN 61010-2-202:2017
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN 61010-2-202:2017
01-september-2017
9DUQRVWQH]DKWHYH]DHOHNWULþQRRSUHPR]DPHULWYHQDG]RULQODERUDWRULMVNR
XSRUDERGHO3RVHEQH]DKWHYH]DHOHNWULþQLSRJRQYHQWLORY ,(&


6DIHW\UHTXLUHPHQWVIRUHOHFWULFDOHTXLSPHQWIRUPHDVXUHPHQWFRQWURODQGODERUDWRU\

XVH3DUW3DUWLFXODUUHTXLUHPHQWVIRUHOHFWULFDOO\RSHUDWHGYDOYHDFWXDWRUV

,(&

Sicherheitsbestimmungen für elektrische Mess-, Steuer-, Regel- und Laborgeräte - Teil 2

-202: Besondere Anforderungen für elektrisch betriebene Ventile und Stellantriebe (IEC

61010-2-202:2016)
Règles de sécurité pour appareils électriques de mesurage, de régulation et de

laboratoire - Partie 2-202: Exigences particulières pour les actionneurs à vanne à

commande électrique (IEC 61010-2-202:2016)
Ta slovenski standard je istoveten z: EN 61010-2-202:2017
ICS:
19.080 (OHNWULþQRLQHOHNWURQVNR Electrical and electronic
SUHVNXãDQMH testing
23.060.01 Ventili na splošno Valves in general
71.040.10 Kemijski laboratoriji. Chemical laboratories.
Laboratorijska oprema Laboratory equipment
SIST EN 61010-2-202:2017 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 61010-2-202:2017
---------------------- Page: 2 ----------------------
SIST EN 61010-2-202:2017
EUROPEAN STANDARD EN 61010-2-202
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2017
ICS 13.110; 17.020; 19.020; 25.040.40
English Version
Safety requirements for electrical equipment for measurement,
control and laboratory use - Part 2-202: Particular requirements
for electrically operated valve actuators
(IEC 61010-2-202:2016)

Règles de sécurité pour appareils électriques Sicherheitsbestimmungen für elektrische Mess-,

de mesurage, de régulation et de laboratoire - Steuer-, Regel- und Laborgeräte -

Partie 2-202: Exigences particulières pour les actionneurs Teil 2-202: Besondere Anforderungen für elektrisch

à vanne à commande électrique betriebene Ventile und Stellantriebe
(IEC 61010-2-202:2016) (IEC 61010-2-202:2016)

This European Standard was approved by CENELEC on 2016-08-16. CENELEC members are bound to comply with the CEN/CENELEC

Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC

Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation

under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the

same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,

Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,

Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,

Switzerland, Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels

© 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.

Ref. No. EN 61010-2-202:2017 E
---------------------- Page: 3 ----------------------
SIST EN 61010-2-202:2017
EN 61010-2-202:2017
European foreword

The text of document 65/627/FDIS, future edition 1 of IEC 61010-2-202, prepared by IEC/TC 65

"Industrial-process measurement, control and automation" was submitted to the IEC-CENELEC

parallel vote and approved by CENELEC as EN 61010-2-202:2017.
The following dates are fixed:
(dop) 2017-10-21
• latest date by which the document has to be implemented at
national level by publication of an identical national
standard or by endorsement
(dow) 2020-04-21
• latest date by which the national standards conflicting with
the document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such

patent rights.
Endorsement notice

The text of the International Standard IEC 61010-2-202:2016 was approved by CENELEC as a

European Standard without any modification.
---------------------- Page: 4 ----------------------
SIST EN 61010-2-202:2017
EN 61010-2-202:2017
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are

indispensable for its application. For dated references, only the edition cited applies. For undated

references, the latest edition of the referenced document (including any amendments) applies.

NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod),

the relevant EN/HD applies.

NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is

available here: www.cenelec.eu.
Annex ZA of Part 1 is applicable.
---------------------- Page: 5 ----------------------
SIST EN 61010-2-202:2017
---------------------- Page: 6 ----------------------
SIST EN 61010-2-202:2017
IEC 61010-2-202
Edition 1.0 2016-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
GROUP SAFETY PUBLICATION
PUBLICATION GROUPÉE DE SÉCURITÉ
Safety requirements for electrical equipment for measurement, control and
laboratory use –
Part 2-202: Particular requirements for electrically operated valve actuators
Règles de sécurité pour appareils électriques de mesurage, de régulation et de
laboratoire –
Partie 2-202: Exigences particulières pour les actionneurs à vanne à commande
électrique
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 13.110; 17.020; 19.020; 25.040.40 ISBN 978-2-8322-3446-4

Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN 61010-2-202:2017
– 2 – IEC 61010-2-202:2016  IEC 2016
CONTENTS

FOREWORD ......................................................................................................................... 3

INTRODUCTION ................................................................................................................... 5

1 Scope and object ........................................................................................................... 6

2 Normative references..................................................................................................... 7

3 Terms and definitions .................................................................................................... 7

4 Tests ............................................................................................................................. 7

5 Marking and documentation ........................................................................................... 8

6 Protection against electric shock .................................................................................... 9

7 Protection against mechanical HAZARDS .......................................................................... 9

8 Resistance to mechanical stresses ............................................................................... 10

9 Protection against the spread of fire ............................................................................. 10

10 Equipment temperature limits and resistance to heat .................................................... 10

11 Protection against HAZARDS from fluids ......................................................................... 10

12 Protection against radiation, including laser sources, and against sonic and

ultrasonic pressure ...................................................................................................... 10

13 Protection against liberated gases and substances, explosion and implosion ................ 10

14 Components and subassemblies .................................................................................. 10

15 Protection by interlocks ................................................................................................ 11

16 HAZARDS resulting from application............................................................................... 11

17 RISK assessment ......................................................................................................... 11

Annexes ............................................................................................................................. 12

Bibliography ....................................................................................................................... 13

---------------------- Page: 8 ----------------------
SIST EN 61010-2-202:2017
IEC 61010-2-202:2016  IEC 2016 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
SAFETY REQUIREMENTS FOR ELECTRICAL EQUIPMENT
FOR MEASUREMENT, CONTROL AND LABORATORY USE –
Part 2-202: Particular requirements
for electrically operated valve actuators
FOREWORD

1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising

all national electrotechnical committees (IEC National Committees). The object of IEC is to promote

international co-operation on all questions concerning standardization in the electrical and electronic fields. To

this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,

Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC

Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested

in the subject dealt with may participate in this preparatory work. International, governmental and non-

governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely

with the International Organization for Standardization (ISO) in accordance with conditions determined by

agreement between the two organizations.

2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international

consensus of opinion on the relevant subjects since each technical committee has representation from all

interested IEC National Committees.

3) IEC Publications have the form of recommendations for international use and are accepted by IEC National

Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC

Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any

misinterpretation by any end user.

4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications

transparently to the maximum extent possible in their national and regional publications. Any divergence

between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in

the latter.

5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity

assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any

services carried out by independent certification bodies.

6) All users should ensure that they have the latest edition of this publication.

7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and

members of its technical committees and IEC National Committees for any personal injury, property damage or

other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and

expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC

Publications.

8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is

indispensable for the
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.