Source for standards, engineering specifications, manuals and technical publications

IEC 63058:2026 is to describe product classes and properties, representing the miniature circuit-breaker (MCB), to become a part of the IEC 61360-4: IEC Common Data Dictionary (IEC CDD). It includes data required for product selection as well as data required for engineering. This document intends, as a contribution to the IEC Common Data Dictionary, to be used by catalogue consortia, other database standards and software as a data reference for circuit‑breakers and similar equipment for household use.

This document defines and establishes a framework for access management (AM) and the secure management of the process to access information and information and communications technologies (ICT) resources, associated with the accountability of a subject within some contexts.
This document provides concepts, terms and definitions applicable to distributed access management techniques in network environments.
This document also provides explanations about related architecture, components and management functions.
The subjects involved in access management can be uniquely recognized to access information systems, as defined in the ISO/IEC 24760 series.
The nature and qualities of physical access control involved in access management systems are outside the scope of this document.

This part of the EN IEC 61360 specifies the new data dictionary (domain) “IEC 61360-7 - General items” including its generic concepts. The IEC 61360-7 data dictionary provides concepts (dictionary elements e.g. classes, properties) intended for cross-domain use.

IEC 63369-1:2026 addresses general requirements and methodology, whereas intended IEC 63369-2 and intended IEC 63369-3 address applications of the methodology and default values of the CFF parameters by geographic area (see Annex B). This document provides a comprehensive methodology for the calculation of carbon footprint of industrial type Li-ion battery systems from cradle to grave. Second life and/or usage that was not intended when the battery was put on the market is not taken into account in this document. This document, along with the other parts of this series, does not apply to batteries for portable, SLI and electric road vehicle traction applications. The definition of the parameters used for the carbon footprint calculation allows for comparability of results for all rechargeable Li-ion chemistries. Classes of representative products are defined in this document to allow comparison inside each class. This methodology, based on the data provided by the battery manufacturer, is mainly intended to allow a carbon footprint assessment of several battery solutions over the Cumulated Requested Service (CRS). This assessment can be used in the selection process of the battery purchaser. The methodology can also be used for a variety of purposes such as battery system development, eco-design and participation in voluntary or mandatory programs. The methodology in this document is based exclusively on attributional life cycle assessment (LCA). The carbon footprint calculation of charging equipment and power conversion equipment not necessary for battery functions is not covered in this document.

The CEN/TS 18212 series specifies a generic framework for the establishment of requirements and their evaluation methodology for biometric products. The requirements depend on the biometric mode considered, and are adapted to each scenario, through the definition of a variety of application profiles (APs).
This series of standards are expected to provide the evaluation methodology, the individual tests, and the APs (with their particular requirements).
This document specifies:
-   tests for evaluating the interoperability of all biometric input data (received or read);
-   test for evaluating the interoperability of all biometric output data (stored or transmitted);
-   test for evaluating the interoperability of all exchange of information between the TOE and external components or devices.
NOTE 1   Additional parts are provided covering the specifics of each biometric mode. For each of these modalities, application-independent tests are defined, as well as a set of APs, that detail the applicable tests, the evaluation parameters, and the passing criteria.
The Technical Specifications within this series can be taken by any certification body and/or sector, to define and evaluate the requirements for their biometric products within their selected applications.
NOTE 2   Regarding biometrics for public sector applications, see also BSI TR 03121 [2] which can apply.
NOTE 3   For an overview of sectors addressed in the Cybersecurity Act, see Regulation (EU) 2019/881.
NOTE 4   This part defines all potential tests that could be applicable when evaluating the interoperability of a biometric product. It will be the relevant AP, the one that will specify which of these tests are applicable.

This document establishes a method for measurement of specific heat capacity, cp, using temperature modulated differential scanning calorimetry.

This document describes a standardized methodology and framework for the development and representation of an ontology that supports a global, open-source approach to implementing the ISO standards on the identification of medicinal products (IDMP) (ISO 11615, ISO/TS 20443, ISO/TS 20451, ISO 11238; ISO/TS 19844, ISO 11239, ISO/TS 20440, and ISO 11240). Realization of the full potential of IDMP requires fully self-describing data. For this purpose, this document describes a methodology and framework that complements the existing conceptual and logical models in the ISO documents on IDMP with an IDMP ontology that enables deep, semantic interoperability based on findable, accessible, interoperable and reusable (FAIR) data principles. This methodology and framework enhance the usage of the IDMP data model as the foundation of medicinal product identification and will ultimately enable collaboration towards drug safety and overall operational efficiency.
This document also describes a methodology for the agile adaptation of the ISO documents on IDMP in connection with cross-jurisdictional IDMP-related legislation and initiatives. This document is intended to be complementary to and independent from formal regulatory guidance. Thus, it enables cross-jurisdictional consistency and supports stakeholders in their regional implementations of IDMP standards. This document does not mandate any specific ontology as an implementation tool, nor is it an instructional guideline on how to build ontologies, which is out of scope of this document.
This document includes key use cases described in the ISO documents on IDMP ISO 11615, ISO 11238 and ISO/TS 19844, as well as further use cases arising from the comprehensive deployment of the ISO documents on IDMP via an ontological framework. Thus, an ontology that represents the IDMP standards aims to cover the complete collection of ISO standards on IDMP regarding key interoperability issues that implementing stakeholders are facing.

The document specifies testing procedures for determining calibration error for radiosonde humidity sensors sampled from mass production batches based on varying the levels of relative humidity at atmospheric upper-air temperatures using a laboratory setup. This document provides: technical requirements for a laboratory setup to evaluate the calibration errors of radiosonde humidity measurement; a test procedure for evaluating calibration error of radiosonde humidity sensors for a temperature range1) of −90 °C to 35 °C and for a relative humidity of 1 %rh to 100 %rh. Note, this document, is based upon relative humidity calculated by the percentage of water vapour pressure divided by saturation water vapour pressure over liquid water, not over ice, even at temperatures below 0 °C; hence, the maximum relative humidity is less than 100 %rh below 0 °C; a method for evaluating the uncertainty for the measured radiosonde humidity calibration errors. 1) Currently, the lowest possible temperature of commercially-available climate chambers is approximately -75 °C. The temperature range can be adjusted based on the capability of the climate chamber used.

IEC 61753-022-02: 2026 defines the minimum initial test and measurement requirements and severities which multimode fibre optic connectors terminated as a pigtail or patchcord satisfy in order to be categorized as meeting the IEC standard category C (controlled environment), as defined in IEC 61753‑1. This first edition cancels and replaces the second edition of IEC 61753-022-2 published in 2012. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) addition of provisions for rectangular ferrule connectors; b) additions of terms and definitions; c) update of the fibre naming conventions in accordance with IEC 60793-2-10; d) update of test severities in accordance with IEC 61753‑1; e) addition of the torsion test; f) reduction of the duration of the fibre/cable retention test on reinforced cables from 120 s to 60 s minimum; g) deletion of the static side load test; h) update of the flexing of the strain relief test to use the change in attenuation instead of the transient loss; i) reduction of the number of mating durability cycles for cylindrical ferrule connectors from 500 cycles to 200 cycles; j) addition of the mating durability for rectangular ferrule connectors with 50 cycles; k) addition of Annex B for visual examination of the outer cable sheath movement of reinforced cables as an additional requirement for change of temperature, cable retention and flexing of the strain relief tests.

This document specifies a reference model and process for Collaborative Modeling and Simulation Environment (CMSE), which establishes a general framework of CMSE to provide guidance for implementation of joint simulation projects. The CMSE which is based on the reference process and the reference model including neutral interfaces and meta-models can enable service-oriented share-use of the infrastructure, integration of the software and collaboration of the business to improve collaboration among all kinds of stakeholders involved in a joint simulation project which needs on-demand simulation at any time and any place upon different manufacturing platforms owned by different enterprises or by different departments within an enterprise. This document can not only be applied to manufacturing enterprises but also be applied to other kinds of enterprises. It is intended for use by stakeholders who are concerned with developing and deploying solutions of the joint simulation project based on information and communication technology. It focuses on simulation activities related cross-platform simulation collaboration capability supporting business planning and logistics, manufacturing operations management and production control within or among enterprises, which can cover the levels from 2 to 4 of the functional hierarchy of manufacturing systems in IEC 62264-3[27]. This document specifies the following: the general framework of CMSE; the methodology of the joint simulation project analysis and realization by CMSE. This document does not relate to the simulation irrelevant collaboration environment, and does not specify the specific approach to implement CMSE in the solution formulation of joint simulation projects.

IEC 61000-6-3:2026 is applicable only if no relevant dedicated product or product family EMC emission standard has been published. This part of IEC 61000 for emission requirements applies to electrical and electronic equipment intended for use at residential (see 3.1.21) locations. This part of IEC 61000 also applies to electrical and electronic equipment intended for use at other locations that do not fall within the scope of IEC 61000-6-8 or IEC 61000-6-4. The intention is that all equipment used in the residential, commercial and light-industrial locations are covered by IEC 61000-6-3 or IEC 61000-6-8. If there is any doubt the requirements in IEC 61000-6-3 apply. Equipment that has a radio function (3.1.20) are included in the scope of this document. However, the emission requirements in this document are not intended to be applicable to the intentional transmissions from these radio transmitters, their harmonics and their out of band emissions. Not all disturbance phenomena have been included for testing purposes but only those considered relevant for the equipment intended to operate within the locations included within this document. The objectives of this document are: - to establish requirements that provide an adequate level of protection of radio reception in the frequency range 9 kHz to 400 GHz; - to establish requirements that provide an adequate level of protection against conducted and radiated electromagnetic disturbances emitted by equipment in the scope of this document; - to support the reproducibility of measurement and the repeatability of results. NOTE 1 In special cases, situations will arise where the levels specified in this document will not offer adequate protection; for example, where a sensitive receiver is used in close proximity to an equipment. In these instances, special mitigation measures can be employed. NOTE 2 Disturbances generated in fault conditions of equipment are not covered by this document. NOTE 3 The requirements in this document are more stringent or equivalent to the requirements specified in IEC 61000-6-4 and IEC 61000-6-8. This fourth edition cancels and replaces the third edition published in 2020. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) the addition of magnetic field emission requirements, including the measurement of WPT function; b) the extension of low-voltage AC mains power requirements to cover the range 9 kHz to 150 kHz; c) products with a radio function have been added to the scope; d) limits in a FAR for rack mounted equipment have been added.

This document specifies the general requirements on procedures for the preservation, handling and storage of samples of sewage and waterworks sludge, suspended matter, marine sediments and freshwater sediments for either chemical, physical, radiochemical, hydrobiological or microbiological examination, or all, in the laboratory. The procedures in this document are not applicable to dried samples of sludge, sediment and suspended matter. NOTE The storage conditions given do not necessarily apply for derived samples, e.g. sediment eluates or extracts. This document is not applicable to samples intended for biotesting with ecotoxicological or biological assays (which is specified in ISO 5667-16[5]) nor intended for microplastics (which is specified in ISO 5667-27[7]).

IEC 61300-2-33:2026 evaluates the behaviour of a fibre optic mechanical splice, a fibre management system, a protective housing or a hardened connector after being subjected to a specified number of assembly and disassembly operations. The test procedures described in this document simulate conditions that the component can encounter during its service lifetime to check the following performance characteristics: - capability of an optical mechanical splice to be reinstalled after being disassembled; - capability to reintroduce fibre management systems and protective housings, accessing fibres and optical components and making reconfigurations without disturbing transmission in adjacent fibre circuits; - sealing performance of the protective housing after frequent opening and closing operations; - sealing performance of the hardened connector after frequent mating and demating operations. This fourth edition cancels and replaces the third edition published in 2012. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) update of the terms and definitions according to IEC 61753-1:2018 and IEC 61756‑1:2019; b) update of the test severities according to the new edition of IEC 61753-1:2018; c) addition of procedure D to verify the sealing performance after frequent mating and demating of a hardened connector.

This document, within the context of methods and tools that support adoption, construction, operation, and management of product line maturity framework, specifies: processes for managing, operationalizing, and supporting product line maturity framework adoption (those processes are described in terms of purpose, inputs, tasks, and outcomes); method capabilities to support the defined tasks of each process; tool capabilities that automate or semi-automate tasks and methods. This document does not concern the processes and capabilities of methods and tools for a single system but rather deals with those for a family of products.

This document specifies necessary but not sufficient safety requirements for the use of SbW systems in passenger cars and light commercial vehicles for series application. This document does not replace the full application of the ISO 26262 series of standards and their implementation in safety-related measures. This document defines requirements for manual driving where the driver holds the steering wheel. NOTE Misuse of hands-free driving is not considered. This document does not contain any requirements for the use of automated lateral vehicle control functions. The requirements consider systems consisting of a road wheel actuator (RWA), hand wheel actuator (HWA), and a steering wheel for driver input. Deviating concepts need to be analysed by the user for transferability.

This document specifies requirements for the most important metrological and design characteristics of plain limit gauges of linear size. This document defines the different types of plain limit gauges used to verify linear dimensional specifications associated with linear size. This document also defines the design characteristics and the metrological characteristics for these limit gauges as well as the new or wear limits state maximum permissible limits (MPLs) for the new state or wear limits state for these metrological characteristics. In addition, this document describes the use of limit gauges. It covers linear sizes of up to 500 mm.

This document specifies technical safety requirements and measures to be adopted by persons undertaking the design, manufacture and supply of press brakes which are intended to work cold metal or material partly of cold metal but which can be used in the same way to work other sheet materials (e.g. cardboard, plastic, rubber, leather) and also referred to as machines. NOTE 1 The design of a machine includes the study of the machine itself, taking into account all phases of the “life” of the machine mentioned in ISO 12100:2010, 5.4, and the drafting of the instructions related to all the above phases. This document covers the following types of machines (see Annex J): hydraulic press brakes; hydraulic servo-drive press brakes; screw servo-drive press brakes; belt-spring servo-drive press brakes. The requirements in this document take account of intended use, as defined in ISO 12100:2010, 3.23, as well as reasonably foreseeable misuse, as defined in ISO 12100:2010, 3.24. This document presumes access to the press brake from all directions, deals with all significant hazards during the various phases of the life of the machine described in Clause 4, and specifies the safety measures for both the operator and other exposed persons. NOTE 2 All significant hazards means those identified or associated with press brakes at the time of the publication of this document. This document can also be used as a guide for the design of press brakes which are intended to be integrated in a manufacturing system. This document deals with all significant hazards, hazardous situations or hazardous events relevant to press brakes and ancillary devices (see Clause 4) when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer. This document specifies the safety requirements for press brakes defined in Clause 3. This document does not cover press brakes which transmit energy to impart beam motion by using pneumatic means or mechanical clutch or press brakes that use combination of technologies (e.g. combined hydraulic and screw servo-drive press brake or combined hydraulic servo-drive and screw servo-drive press brake). This document does not cover machines whose principal designed purpose is: sheet folding by rotary action; tube and pipe bending by rotary action; roll bending. This document does not cover hazards related to the use of press brakes in explosive atmospheres. This document is not applicable to press brakes which are manufactured before the date of its publication. This document does not cover the safety aspect of equipment for automatic workpiece loading and unloading where provided. Guidance on how to take into account additional automatic loading and unloading equipment can be found in ISO 11161:2007.

This document defines a generic incident management process and supporting documentation that can be used to implement incident management and to manage incidents within most organizations, projects or operations activities for a system, service, software, or product. This document also provides supporting diagrams describing the process and example documents. This document is applicable to incident management in all life cycle models (e.g. incremental, waterfall, evolutionary, agile). This document covers incidents identified across the life cycle, including those that arise during both development (e.g. defects) and operation (e.g. those handled by service management).

This document specifies a micrographic method of determining the non-metallic inclusions in rolled or forged steel products having a reduction ratio of at least 3 using the images of a standard reference chart or direct measurement by image analysis technologies. The standard reference chart described in this document is not entirely applicable for certain types of steel (e.g. free cutting steels).

This document provides requirements on identification and labelling of medicinal products from the point of manufacturing of packaged medicinal product to the point of dispensing the product.
This document outlines commonly accepted international practices for automatic identification and data capture (AIDC) barcoding solutions for applications and applies to manufacturers, distributors, healthcare facilities and all parties involved in labelling and distribution of packaged medicinal products. These users can, however, consider the coding interoperability requirements for other AIDC technologies, e.g. radio frequency identification (RFID); that technology is not addressed in this document except as for information.