CEN - European Committee for Standardization

This document specifies safety and performance requirements of domestic ceramic and glass ceramic cookware for use on top of a stove, cooker or hob.
This document envisages that oven top applications for ceramic utensils involve all or specific parts of the cooking operation, for example, the browning of meat, where the remainder of the cooking can be completed in an oven or on top of the stove.
NOTE   Requirements for suitability for use with induction hobs are in the process of being compiled.

This European Standard specifies the material requirements and testing procedures applicable to wrought and cast aluminium and aluminium alloys intended for use in the production of pressure equipment.
This European Standard covers:
-   the products forms, grades and tempers of wrought and cast aluminium and aluminium alloys which may be used for such applications together with data for wrought and cast alloys over their permissible working temperature ranges;
-   the permissible alloys/ tempers covered by this are those given in Table A.1 and in B.1 for wrought alloys and in Table A.2 and in B.2 for castings;
-   the technical conditions for inspection and delivery, mechanical property limits and tolerances on form and dimensions by reference to the appropriate European standards for the relevant wrought and cast aluminium and aluminium alloys, and
-   additional requirements which are specific to pressure equipment applications.
It applies to hot-rolled plate, cold-rolled sheet/ strip/ circles, extruded or extruded and cold drawn rod/bar, tube, extruded open / hollow profiles, forgings and castings, by this standard are those given in Table A.1 for wrought alloys and in Table A.2 for castings.
It is the sole objective of this standard to cover materials only for pressure purposes and it excludes any elements of fabrication or fabrication methods for pressure equipment; such information can be found in the relevant standards listed in the "Bibliography" section.

This document specifies a publication sub-model within the DATEX II model that supports the publication of electronic traffic regulations.
This publication is intended to support the exchange of informational content from road traffic authorities issuing traffic regulation orders and organisations implementing these orders to other organisations providing ITS services or onward information exchange.

This document specifies the characteristics of fusion fittings made from polyethylene (PE) as well as of mechanical fittings for piping systems in the field of the supply of gaseous fuels.
It also specifies the test parameters for the test methods referred to in this document.
In conjunction with Parts 1, 2, 4 and 5 of EN 1555, it is applicable to PE fittings, their joints and to joints with components of PE and other materials intended to be used under the following conditions:
a) a maximum operating pressure, MOP, up to and including 10 bar1 at a reference temperature of 20 °C for design purposes;
b) an operating temperature between −20 °C and 40 °C.
NOTE 1 For operating temperatures between 20 °C and 40 °C, derating coefficients are defined in EN 1555-5:2021.
EN 1555 (all parts) covers a range of maximum operating pressures and gives requirements concerning colours.
NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
This document is applicable for fittings of the following types:
a) electrofusion socket fittings;
b) electrofusion saddle fittings;
c) spigot end fittings (for butt fusion using heated tools and electrofusion socket fusion);
d) mechanical fittings.
NOTE 3 The fittings can be, for example, in the form of couplers, equal and reduced tees, reducers, saddles, elbows or caps.

This document specifies the characteristics of pipes made from polyethylene (PE) for piping systems in the field of the supply of gaseous fuels.
It also specifies the test parameters for the test methods referred to in this document.
In conjunction with Parts 1 and 3 to 5 of EN 1555, it is applicable to PE pipes, their joints and to joints with components of PE and other materials intended to be used under the following conditions:
a) a maximum operating pressure, MOP, up to and including 10 bar1at a reference temperature of 20 °C for design purposes;
b) an operating temperature between −20 °C and 40 °C.
NOTE 1 For operating temperatures between 20 °C and 40 °C derating coefficients are defined in EN 1555-5:2021.
EN 1555 covers a range of maximum operating pressures and gives requirements concerning colours.
It covers three types of pipe:
— PE pipes (outside diameter dn) including any identification stripes;
— PE pipes with co-extruded layers on either or both the outside and/or inside of the pipe (total outside diameter dn) as specified in Annex A, where all layers have the same MRS rating. A coextruded pipe made of a combination of PE 100 and PE 100-RC layers shall be regarded as PE 100 and marked accordingly;
— PE pipes (outside diameter dn) with a peelable, contiguous thermoplastics additional layer on the outside of the pipe (‘coated pipe’) as specified in Annex B.
NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

This document specifies the characteristics of valves made from polyethylene (PE) for piping systems in the field of the supply of gaseous fuels.
It is applicable to isolating unidirectional and bi-directional valves with spigot ends or electrofusion sockets intended to be fused with PE pipes or fittings conforming to EN 1555-2:2021 and EN 1555-3:2021 respectively.
Valves made from materials other than PE, designed for the supply of gaseous fuels conforming to the relevant standards can be used in PE piping systems according to EN 1555 (all parts), provided that they have PE connections for butt fusion or electrofusion ends, including integrated material transition joints, conforming to EN 1555-3:2021.
It also specifies the test parameters for the test methods referred to in this document.
In conjunction with Parts 1, 2, 3 and 5 of EN 1555, it is applicable to PE valves, their joints and to joints with components of PE and other materials intended to be used under the following conditions:
a) a maximum operating pressure, MOP, up to and including 10 bar1 at a reference temperature of 20 °C for design purposes;
NOTE 1 For the purpose of this document and the references to EN ISO 82332, MOP is considered to be nominal pressure.
b) an operating temperature between −20 °C to 40 °C.
NOTE 2 For operating temperatures between 20 °C and 40 °C, derating coefficients are defined in EN 1555-5.
EN 1555 (all parts) covers a range of maximum operating pressures and gives requirements concerning colours.
NOTE 3 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
This document covers valve bodies designed for connection with pipes with a nominal outside diameter dn ≤ 400 mm.

This document specifies the general aspects of polyethylene (PE) piping systems in the field of the supply of gaseous fuels.
It also specifies the test parameters for the test methods referred to in this document.
In conjunction with Parts 2 to 5 of EN 1555, this document is applicable to PE pipes, fittings, and valves, their joints and to joints with components of other materials intended to be used under the following conditions:
a) a maximum operating pressure, MOP, up to and including 10 bar1 at a reference temperature of 20 °C for design purposes;
b) an operating temperature between -20 °C and 40 °C.
NOTE 1 For operating temperatures between 20 °C and 40 °C, derating coefficients are defined, see EN 1555-5 [3].
EN 1555 (all parts) covers a range of maximum operating pressures and gives requirements concerning colours.
NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

This part of EN 13476, together with EN 13476-1, specifies the definitions and requirements for pipes, fittings and the system based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems that are intended to be used for non-pressure underground drainage and sewerage systems.
This part is applicable to pipes and fittings with smooth internal and external surfaces, designated as Type A.
It specifies test methods and test parameters as well as requirements.
This part is applicable to:
a)   structured-wall pipes and fittings, which are intended to be used buried underground outside the building structure; reflected in the marking of products by "U";
b)   structured-wall pipes and fittings, which are intended to be used buried underground both outside (application area code "U") and within the building structure (application area code "D"); reflected in the marking of products by "UD".
This part is applicable to structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints as well as welded and fused joints.
This part covers a range of pipe and fitting sizes, materials, pipe constructions, stiffness classes, application classes, and tolerance classes and gives recommendations concerning colours.
NOTE   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

This part of EN 13476, together with EN 13476-1, specifies the definitions and requirements for pipes, fittings and the system based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems that are intended to be used for non-pressure underground drainage and sewerage systems.
This part is applicable to pipes and fittings with smooth internal and profiled external surfaces, designated as Type B.
It specifies test methods and test parameters as well as requirements.
This part is applicable to:
a)   structured-wall pipes and fittings, which are intended to be used buried underground outside the building structure, reflected in the marking of products by "U";
b)   structured-wall pipes and fittings, which are intended to be used buried underground both outside (application area code "U") and within the building structure (application area code "D"), reflected in the marking of products by "UD".
This part is applicable to structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints as well as welded and fused joints.
This part covers a range of pipe and fitting sizes, materials, pipe constructions, stiffness classes, application classes, and tolerance classes and gives recommendations concerning colours.
NOTE   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

This document gives guidance for the assessment of conformity of materials, products, joints and assemblies in accordance with the applicable part(s) of EN 13476 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE 1   The quality management system is expected to conform to or be no less stringent than the relevant requirements to EN ISO 9001 [1].
NOTE 2   If third-party certification is involved, the certification body can be accredited to EN ISO/IEC 17065 [2] or EN ISO/IEC 17021 [3], as applicable.
NOTE 3 In order to help the reader, a basic test matrix is given in Annex A.
In conjunction with EN 13476 1, EN 13476 2 and EN 13476 3 this document is applicable to Plastics piping systems for non-pressure underground drainage and sewerage — Structural-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE):
-   for non-pressure underground drainage and sewerage outside the building structure (application area code “U”) reflected in the marking of products by “U”, and
-   for non-pressure underground drainage and sewerage for both buried in ground within the building structure (application area code “D” and outside the building structure (application area code “U”) reflected in the marking of products by “UD”.

This European Standard specifies a method for determining the creep deformation of bonded specimens loaded in bending shear. It is applicable to adhesives used in load bearing timber structures.
It is suitable for the following applications:
a)   for assessing the compliance of adhesives to EN 15425 and EN 16254;
b)   for assessing the suitability and quality of adhesives for load bearing timber structures.
This test is intended primarily to obtain performance data for the classification of adhesives for load bearing timber structures according to their suitability for use in defined climatic environments.
This method is not intended to provide data for structural design, and does not necessarily represent the performance of the bonded member in service.

This European Standard, together with EN 13476 2 and EN 13476 3, specifies the definitions and general requirements for pipes, fittings and the system based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems that are to be used for non-pressure underground drainage and sewerage systems.
This standard is applicable to:
a)   structured-wall pipes and fittings, which are to be used buried in the ground outside a building structure only; reflected by the marking of products by "U";
b)   structured-wall pipes and fittings, which are to be used buried in ground both outside (application area code "U") and within a building structure (application area code "D"); reflected in the marking of products by "UD".
In conjunction with EN 13476 2 and EN 13476 3, it is applicable to structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints, as well as welded and fused joints.
This part specifies general aspects and gives guidance concerning a national selection of requirement levels and classes where part 2 and part 3 of this standard provide options.
EN 13476 2 and EN 13476 3 specify material characteristics, dimensions and tolerances, test methods, test parameters and requirements for pipes with smooth internal and external surfaces, Type A, and pipes with smooth internal and profiled external surfaces, Type B.
This standard, together with EN 13476 2 and EN 13476 3, covers a range of pipe and fitting sizes, materials, pipe constructions, stiffness classes and tolerance classes and offers recommendations concerning colours.
NOTE 1   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
NOTE 2   Pipes, fittings and other components conforming to any plastic product standards referred to in Clause 2 can be used with pipes and fittings conforming to this standard, when they conform to the requirements for joint dimensions given in part 2 and part 3 of this standard and to the performance requirements given in Clause 9.

ISO 3210:2017 specifies methods of assessing the quality of sealed anodic oxidation coatings on aluminium and its alloys by measurement of the loss of mass after immersion in acid solution(s).
It consists of the following two methods.
-      Method 1: Assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass after immersion in a phosphoric acid based solution without prior acid treatment.
-      Method 2: Assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass after immersion in a phosphoric acid based solution with prior acid treatment.
Method 1 is applicable to anodic oxidation coatings intended for decorative or protective purposes or where resistance to staining is important.
Method 2 is applicable to anodic oxidation coatings intended for outdoor architectural purposes. For less severe applications, Method 1 can be more suitable.
The methods are not applicable to the following:
-      hard-type anodic oxidation coatings which normally are not sealed;
-      anodic oxidation coatings that have been sealed only in dichromate solutions;
-      anodic oxidation coatings produced in chromic acid solutions;
-      anodic oxidation coatings that have undergone treatment to render them hydrophobic.
NOTE 1    The methods assess the quality of hydrothermal sealing applied to anodized aluminium. They can be appropriate for other sealing methods.
NOTE 2    The methods are destructive and can serve as reference methods in case of doubt or dispute regarding the results of the test for loss of absorptive power (see ISO 2143) or the measurement of admittance (see ISO 2931).

This Technical Report describes how trading partners may extend the core invoice model and the related business rules and code lists, in order to support business cases that are specific to their trading environment, while at the same time maintaining semantic interoperability with the core invoice model.
This Technical Report does not define a methodology for creation of core invoice usage specification, nor does it describe the detailed process of syntax binding.

ISO 5577:2017 defines the terms used in ultrasonic non-destructive testing and forms a common basis for standards and general use. This document does not cover terms used in ultrasonic testing with phased arrays.
NOTE          Terms for phased array ultrasonic testing are defined in EN 16018.

This European Standard specifies a method of determining the ability of adhesive bonds to resist long-term sustained load applied vertical to the glue lines. It is applicable to adhesives used in load-bearing timber structures.
It is suitable for the following applications:
a)   for assessing the compliance of adhesives according to EN 15425 and EN 16254;
b)   for assessing the suitability and quality of adhesives for load-bearing timber structures;
c)   for assessing the effect on the bond strength resulting from long-term sustained load at cyclic climate conditions.
This method is intended primarily to obtain performance data for the classification of adhesives for load bearing timber structures according to their suitability for use in defined climatic environments.
This method is not intended to provide data for structural design, and does not necessarily represent the performance of the bonded member in service.

This European Standard specifies a laboratory method of determining the open assembly time in standard climate (20 ±2) °C and (65 ±5) % relative humidity (hereafter climate [20/65]).
This European Standard is intended to determine the open assembly time using a defined procedure for obtaining a reliable base for comparison of open assembly time between adhesives under referenced conditions.
The method gives a result that cannot be applied to the safe manufacture of timber structures without taking into account the influence of factors such as timber density, moisture content, factory temperature and relative air humidity.

This document specifies a laboratory method of determining the minimum pressing time for line thicknesses close contact, 0,2 mm, 0,3 mm and 0,5 mm, at three temperatures and three wood moisture contents.
This document is intended to determine the minimum pressing time using a defined procedure for obtaining a reliable base for comparison of minimum pressing time between adhesives under referenced conditions.
The method gives a result that cannot be applied to the safe manufacture of timber structures without taking into account the influence in variation of factors such as timber density, moisture content, factory temperature and relative air humidity.

ISO/IEEE 11073-10103:2014 extends the base nomenclature provided in IEEE 11073 to support terminology for implantable cardiac devices. Devices within the scope of this nomenclature are implantable devices such as pacemakers, defibrillators, devices for cardiac resynchronization therapy, and implantable cardiac monitors. The discrete terms necessary to convey a clinically relevant summary of the information obtained during a device interrogation are defined in this nomenclature. To improve workflow efficiencies, cardiology and electrophysiology practices require the management of summary interrogation information from all vendor devices and systems in a central system such as an Electronic Health Records (EHR) system or a device clinic management system. To address this requirement, the Implantable Device, Cardiac (IDC) Nomenclature defines a standard-based terminology for device data. The nomenclature facilitates the transfer of data from the vendor proprietary systems to the clinic EHR or device clinic management system.

This European Standard specifies a method to determine the sensitivity of a textile floor covering for change in colour or structure after water has been spilled on the surface.
This change can be due to a real colour change or to a migration and concentration of chemicals from pre-coat or backing during the drying process. This concentration of chemicals on a part of the surface is one of the major causes of accelerated uneven soiling of textile floor covering.

This standard specifies and gives guidance on: - general requirements for storage of water outside consumers' buildings, including service reservoirs for potable water and reservoirs containing water not for human consumption at intake works or within treatment works, excluding those that are part of the treatment process; - design; - general requirements for product standards; - requirements for checks, testing and commissioning; - operational requirements; requirements for rehabilitation and repair.

Within the context of the ISO/IEEE 11073 family of standards for device communication, this standard establishes a normative definition of the communication between medication monitoring devices and managers (e.g., cell phones, personal computers, personal health appliances, set top boxes) in a manner that enables plug-and-play interoperability. It leverages appropriate portions of existing standards, including ISO/IEEE 11073 terminology, information models and application profile. It specifies the use of specific term codes, formats, and behaviors in telehealth environments restricting ambiguity in base frameworks in favor of interoperability. This standard defines a common core of communication functionality for medication monitors. In this context, medication monitors are defined as devices that have the ability to determine and communicate (to a manager) measures of a user’s adherence to a medication regime.

This document specifies a method for determining the no-fire current of electric detonators. This document applies to explosives for civil uses.

This standard establishes a normative definition of communication between personal health continuous glucose monitor (CGM) devices (agents) and managers (e.g., cell phones, personal computers, personal health appliances, set top boxes) in a manner that enables plug-and-play interoperability. It leverages work done in other ISO/IEEE 11073 standards including existing terminology, information profiles, application profile standards, and transport standards. It specifies the use of specific term codes, formats, and behaviors in telehealth environments, restricting optionality in base frameworks in favor of interoperability. This standard defines a common core of communication functionality of CGM devices. In this context, CGM refers to the measurement of the level of glucose in the body on a regular (typically 5 minute) basis through a sensor continuously attached to the person.

This document specifies a method for the determination of the velocity of detonation of detonating cords.
This document does not apply to safety fuses.

This document specifies conformance tests in the form of an abstract test suite (ATS) for a system under test (SUT) that implements an electric-vehicle communication controller (EVCC) or a supply-equipment communication controller (SECC) for all common requirements specified in ISO 15118-20 that are independent of a particular charging type (AC, DC, ACD, WPT charging). These conformance tests specify the testing of capabilities and behaviours of an SUT, as well as checking what is observed against the conformance requirements specified in ISO 15118-20 and against what the implementer states the SUT implementation's capabilities are.
The capability tests within the ATS check that the observable capabilities of the SUT are in accordance with the static conformance requirements specified in ISO 15118-20. The behaviour tests of the ATS examine an implementation as thoroughly as practical over the full range of dynamic conformance requirements specified in ISO 15118-20 and within the capabilities of the SUT.
A test architecture is described in correspondence to the ATS. The abstract test cases in this document are described leveraging this test architecture and are specified in descriptive tabular format covering the ISO/OSI layer 3 to 7 (network to application layers).
In terms of coverage, this document only covers normative sections and requirements in ISO 15118-20. This document additionally refers to specific tests for requirements on referenced standards (e.g. IETF RFCs, W3C Recommendation, etc.) if they are relevant in terms of conformance for implementations according to ISO 15118-20. However, it is explicitly not intended to widen the scope of this conformance specification to such external standards, if it is not technically necessary for the purpose of conformance testing for ISO 15118-20. Furthermore, the conformance tests specified in this document do not include the assessment of performance nor robustness or reliability of an implementation. They cannot provide judgments on the physical realization of abstract service primitives, how a system is implemented, how it provides any requested service, or the environment of the protocol implementation. Furthermore, the abstract test cases specified in this document only consider the communication protocol and the system's behaviour specified in ISO 15118-20. Power flow between the EVSE and the EV is no prerequisite for the test cases specified in this document.

This document specifies a method to determine the series firing current of electric detonators. This document is applicable to explosives for civil uses.

This document specifies a test method for the verification of the thermal stability at 75 °C of explosives for blasting, boosters and explosive substances.
This document also applies to black powder when used for blasting.
This document also applies to solid gun propellants, solid rocket propellants, black powder used as propellants, for safety fuse or for pyrotechnics and powder cakes as covered by EN 13938-1:2025.

This document specifies a test method for the verification of the transmission of detonation of cartridged explosives for blasting.
This document does not apply to blasting explosives in bulk form, boosters, black powder and explosive substances.

This document specifies a test method for the verification of the flash-over voltage of electric detonators.
This document does not apply to non-electric, electronic, plain or semi-finished detonators.
This document does not apply to surface connectors, detonating cord relays, leading wires, shock tubes, coupling accessories and electronic initiation systems.

This document specifies test methods for the verification of the initiation of explosives for blasting and boosters by its means of initiation.
The means of initiation for explosives for blasting covered in this document are detonators, detonating cords and boosters. The means of initiation for boosters covered in this document are detonators and detonating cords.
This document does not apply to black powder used for blasting and explosive substances.

This document, when used together with ISO 16122-1:2024, specifies the requirements and test methods for the inspection of fixed and semi-mobile sprayers, when in use.
The requirements relate mainly to the condition of the sprayer with respect to its potential risk for the environment and its performance to achieve good application.
NOTE            Requirements for the protection of inspectors during an inspection are given in ISO 16122-1:2024.

This document establishes key principles for the investigation of microplastics in drinking water and water with low content of natural suspended solids using a microscopy technique coupled with vibrational spectroscopy.
This method is applicable to:
—    determine the size of microplastics [which range from 1 µm to 5 000 µm], count them and classify them by size range;
—    identify the chemical composition of microplastics, the main ones (most used in industry and most abundant in the environment) being: polyethylene (PE), polypropylene (PP), polyethylene terephthalate (PET), polycarbonate (PC), polystyrene (PS), polytetrafluoroethylene (PTFE), polyvinyl chloride (PVC), polyamide (PA), polymethyl methacrylate (PMMA) and polyurethane (PU);
This method is applicable to water with a low content of organic matter and other suspended matter as defined in ISO 6107 (1 mg/l to 100 mg/l or lower when interfering with the determination), i.e.,
—    ultrapure water;
—    water intended for human consumption;
—    raw groundwaters.
Given the very low concentrations of microplastics usually present in these waters, special attention needs to be paid to potential sources of contamination during sample preparation.
This method is intended to determine and characterize large numbers of particles in the sample in automatic mode.
This method can also identify the nature of the other particles that are outside the scope of this document, for example minerals, proteins, cellulose and pigments.
This method does not apply to the characterization of substances intentionally added to or adsorbed on the surface of microplastics. This method does not apply to the determination of the geometric shape of microplastics.

This document specifies the requirements for solid propellants, solid rocket propellants, powder cakes and black powders for pyrotechnics and safety fuses, when subjected to the test methods defined in the standards referenced to in Clause 2.

This document specifies the measurement and test methods for general characteristics of cold formed helical extension springs made from round wire, excluding dynamic testing.

This document specifies a test procedure for determination of the size of industrial radiographic gamma sources of 0,5 mm or greater, made from the radionuclides Iridium 192, Ytterbium 169, Selenium 75 or Cobalt 60, by a radiography method with X-rays. The source size of a gamma radiation source is an important factor which affects the image quality of gamma ray images.
The source size is determined with an accuracy of ±10 % but typically not better than ±0,1 mm.
The source size is provided by the manufacturer as the mechanical dimension of the source insert. A measurement can be required if the manufacturing process is validated or monitored after implementation of the source into the holder.
This document can be used for other radionuclides after validation.
The standard test method ASTM E1114 provides further information on the measurement of the Ir-192 source size, the characterization of the source shape, and its correct assembly and packaging.

This document specifies a method for determination of resistance to hydrostatic pressure of electric detonators, non-electric detonators, electronic detonators, surface connectors and detonating cord relays.
Detonating cord relays, stated by the manufacturer to be used in dry conditions, are excluded.
This document is applicable to explosives for civil uses.

This document specifies a method for determining the delay time accuracy of electric detonators, non-electric detonators, surface connectors and detonating cord relays with pyrotechnic delay elements.
This document applies to explosives for civil uses.
NOTE The method for determining the delay time accuracy for electronic initiation systems is included in prEN 13763-27.

This European Standard describes the specific ‘Design for PRM use’ requirements applying to rolling stock and the assessment of those requirements. The following applies to this standard:
—   the definitions and requirements describe specific aspects of ‘Design for PRM use’ required by persons with disabilities and persons with reduced mobility as defined in the PRM TSI;
—   this standard defines elements which are universally valid for obstacle free travelling including toilets, elements for sitting, standing and moving and clearways and internal doors. The definitions and requirements of this standard are to be used for rolling stock applications;
—   this standard only refers to aspects of accessibility for PRM passengers. It does not define general requirements and general definitions;
—   this standard assumes that the rolling stock is in its defined operating condition;
—   where minimum or maximum dimensions are quoted these are absolute NOT nominal requirements.
The 'Equipment and components' standard is written in three parts:
—   Part 1 contains:
—   toilets;
—   this document is Part 2 and contains:
—   handholds;
—   seats;
—   wheelchair spaces;
—   Part 3 contains:
—   clearways;
—   internal doors.

This document specifies a test method for the verification of the resistance to abrasion of detonating cords.
This document does not apply to safety fuses.

This document specifies two test methods for the verification of the insensitiveness to impact.
This document is applicable to electric detonators, non-electric detonators, electronic detonators, plain detonators, semi-finished detonators, surface connectors and detonating cord relays as well as shock tubes.
This document does not apply to electronic initiation systems.

This document specifies a method to determine the tendency of a propellant to undergo transition from deflagration to detonation (DDT). It applies to propellants of a grain size up to 8 mm. This method does not apply to black powder and rocket propellant.
NOTE 1   Due to the nature of the shape of grains (heterogeneous), the combustion of the rocket propellant can cause a crack of the grain causing an explosion of the rocket motor.
NOTE 2   Black powders properties differ significantly from propellant and explosives because black powders are capable of maintaining stable combustion at high velocities without experiencing deflagration - detonation transition.

This document specifies requirements for explosives for blasting, boosters and explosive substances.
This document also applies to black powder when used for blasting.
NOTE   This document does not apply to black powder when used as propellant, for pyrotechnics or for safety fuses; for requirements for black powder used as propellant, for pyrotechnics or for safety fuses see EN 13938-1:2025.

This document specifies a method for determining the electrical resistance of electric detonators. This document applies to explosives for civil uses.

This document specifies two test methods for the determination of the velocity of detonation of explosives for blasting.
This document does not apply to boosters and explosive substances.
NOTE   This document does not apply to black powder. The burning rate of black powder is determined in accordance with EN 13938-4:2025.

This document specifies a method for the determination of the index of initiating capability for detonating cords.
The test method specified in this document is intended to assess only the index of initiation capability of detonating cords. See EN 13630-7:2025 for a test method for the verification of the reliability of initiation.
This document does not apply to safety fuses.

This document describes the specific ‘Design for PRM use’ requirements applying to rolling stock and the assessment of those requirements. The following applies to this document:
—   The definitions and requirements describe specific aspects of ‘Design for PRM use’ required by persons with disabilities and persons with reduced mobility as defined in the PRM TSI
—   This document defines elements which are universally valid for obstacle-free travelling including toilets, elements for sitting, standing and moving and clearways and internal doors. The definitions and requirements of this standard are to be used for rolling stock applications
—   This document only refers to aspects of accessibility for PRM passengers; it does not define non-PRM related requirements and definitions.
—   This document assumes that the rolling stock is in its defined operating condition.
—   Where minimum or maximum dimensions are quoted these are absolute NOT nominal requirements.
The 'Equipment and components' standard is written in three parts:
—   Part 1 contains:
—   Toilets
—   Part 2 contains:
—   Handholds
—   Seats
—   Wheelchair spaces
—   This document is Part 3 and contains:
—   Clearways
—   Internal doors.

Within the context of the ISO/IEEE 11073 family of standards for device communication, this standard establishes a normative definition of the communication between independent living activity hubs and managers (e.g., cell phones, personal computers, personal health appliances, and set top boxes) in a manner that enables plug-and-play interoperability. It leverages appropriate portions of existing standards, including ISO/IEEE 11073 terminology and information models. It specifies the use of specific term codes, formats, and behaviors in telehealth environments restricting ambiguity in base frameworks in favor of interoperability. This standard defines a common core of communication functionality for independent living activity hubs. In this context, independent living activity hubs are defined as devices that communicate with simple situation monitors (binary sensors), normalize information received from the simple environmental monitors, and provide this normalized information to one or more managers. This information can be examined, for example, to determine when a person’s activities/behaviors have deviated significantly from what is normal for them such that relevant parties can be notified. Independent living activity hubs will normalize information from the following simple situation monitors (binary sensors) for the initial release of the proposed standard: fall sensor, motion sensor, door sensor, bed/chair occupancy sensor, light switch sensor, smoke sensor, (ambient) temperature threshold sensor, personal emergency response system (PERS), and enuresis sensor (bed-wetting).

This document specifies a test method for the verification of the capacitance, insulation resistance and insulation breakdown of leading wires of electric detonators and electronic detonators.
This document does not apply to non-electric detonators, surface connectors, detonating cord relays, shock tubes and electronic initiation systems.

This European Standard describes the specific ‘Design for PRM use’ requirements applying to both infrastructure and rolling stock and the assessment of those requirements. The following applies to this standard:
—   The definitions and requirements describe specific aspects of ‘Design for PRM use’ required by persons with disabilities and persons with reduced mobility as defined in the PRM TSI.
—   This standard defines elements which are universally valid for obstacle free travelling including lighting, contrast, tactile feedback, transmission of visual and acoustic information. The definitions and requirements of this standard cover the infrastructure and the rolling stock applications.
—   This standard only refers to aspects of accessibility for PRM passengers it does not define non PRM related requirements and definitions.
—   This standard assumes that the infrastructure or rolling stock is in its defined operating condition.
—   Where minimum or maximum dimensions are quoted these are absolute NOT nominal requirements.
The ‘General requirements’ standard is written in three parts:
—   Part 1 contains:
—   contrast;
—   This document is Part 2 and contains:
—   spoken information;
—   written information;
—   tactile information;
—   pictograms;
—   Part 3 contains:
—   lighting;
—   low reflective properties;
—   transparent obstacles;
—   slip resistance.