ISO - CEN ISO TC

ISO corrigendum.

1.1 This International Standard specifies domestic washing and drying procedures for textile testing. The
procedures are applicable to textile fabrics, garments or other textile articles which are subjected to appropriate
combinations of domestic washing and drying procedures. This International Standard also specifies the
reference detergents and ballasts for the procedures.
1.2 Provision is made for
a) 13 different washing procedures based on the use of the reference washing machine Type A: horizontal
axis, front-loading type,
b) 11 procedures based on the use of the reference washing machine Type B: vertical axis, top-loading
agitator type, and
c) 7 procedures based on the use of the reference washing machine Type C: vertical axis, top-loading
pulsator type.
1.3 Each washing procedure represents a single domestic wash.
1.4 This International Standard also specifies six drying procedures:
A — Line dry
B — Drip line dry
C — Flat dry
D — Drip flat dry
E — Flat press
F — Tumble dry
1.5 A complete test consists of a washing and drying procedure.
NOTE Use of different parameters (washing machine type, detergent type and type of tumble drier) may affect test
results for any test using this International Standard. Therefore, parties using this standard are strongly encouraged to
agree on the parameters to be used.

ISO 23210:2009 specifies a standard reference method for the determination of PM10 and PM2,5 mass concentrations at stationary emission sources by use of two-stage impactors. The measurement method is especially suitable for measurements of mass concentrations below 40 mg/m3 as half-hourly averages in standard conditions (273 K, 1 013 hPa, dry gas). It is an acceptable method for the measurement in the flue gas of different installations, such as cement and steel production plants, as well as combustion processes.
ISO 23210:2009 is not applicable to the sampling of flue gases that are saturated with water vapour.
ISO 23210:2009 is not applicable where the majority of the particles are likely to exceed PM10, for example, in the case of raw gases or plant operating failures.
ISO 23210:2009 cannot be used for the determination of the total mass concentration of dust.
ISO 23210:2009 describes the design, use and theory of round-nozzle impactors. It does not exclude other types of impactors, provided these systems meet the performance criteria specified in ISO 23210:2009 in a validation of the impactor performed by an independent testing laboratory.

ISO 22959:2009 specifies a high performance liquid chromatographic (HPLC) procedure for the determination of polycyclic aromatic hydrocarbons (PAHs) in edible fats and oils.
The method has been validated for coconut, olive, sunflower, and soybean oil, and is possibly applicable to other oils, dependent on the determination of appropriate parameters.
The lowest level of quantification for the PAHs is 0,1 µg/kg. The lowest possible amount of each PAH which can be distinguished from the baseline noise has not been determined. The validated concentration range of the method is 0,1 µg/kg to 3,5 µg/kg for each individual PAH. For samples containing (light) PAH contents > 3,5 µg/kg, dilution to bring the contents into the validated range is possible. It is also possible to adjust the range of the calibration curves. However, ranges exceeding 3,5 µg/kg have not been validated.
PAHs which can be determined by this method are: anthracene, phenanthrene, fluoranthene, pyrene, chrysene, benzo[a]anthracene, benzo[e]pyrene, benzo[a]pyrene, perylene, benzo[ghi]perylene, anthanthrene, dibenzo[a,h]anthracene, coronene, indeno[1,2,3-cd]pyrene, benzo[a]fluoranthene, benzo[b]fluoranthene, benzo[k]fluoranthene.

ISO 24415-1:2009 specifies requirements and test methods for the friction between the tips for assistive products for walking and the walking surface. The requirements and test method are based on a usage of tips for ordinary gait on the dry and flat walking surface.
ISO 24415-1:2009 is not applicable to tips manufactured for special purposes.

ISO 19134:2006 specifies the data types and their associated operations for the implementation of multimodal location-based services for routing and navigation. It is designed to specify web services that may be made available to wireless devices through web-resident proxy applications, but is not limited to that environment.

ISO 16000-15:2008 specifies the planning of nitrogen dioxide indoor pollution measurements. In the case of indoor air measurements, the careful planning of sampling and the entire measurement strategy are of particular significance since the result of the measurement may have far-reaching consequences, for example, with regard to ascertaining the need for remedial action or the success of such an action.
An inappropriate measurement strategy may lead to misrepresentation of the true conditions or, worse, to erroneous results.

ISO 11143:2008 specifies requirements and test methods for amalgam separators used in connection with dental equipment in the dental treatment centre. It specifies the efficiency of the amalgam separators in terms of the level of retention of amalgam based on a laboratory test and the test procedure for determining this efficiency. It also includes requirements for the safe functioning of the amalgam separator, for marking, instructions for use, operation and maintenance.
All tests described in ISO 11143:2008 are type tests.

ISO 28300:2008 covers the normal and emergency vapour venting requirements for aboveground liquid petroleum or petroleum products storage tanks and aboveground and underground refrigerated storage tanks designed as atmospheric storage tanks or low-pressure storage tanks. Discussed in ISO 28300:2008 are the causes of overpressure and vacuum; determination of venting requirements; means of venting; selection, and installation of venting devices; and testing and marking of relief devices.
ISO 28300:2008 is intended for tanks containing petroleum and petroleum products but it can also be applied to tanks containing other liquids; however, it is necessary to use sound engineering analysis and judgment whenever ISO 28300:2008 is applied to other liquids.
ISO 28300:2008 does not apply to external floating-roof tanks.

ISO 16000-12:2008 specifies the planning of measurements for polychlorinated biphenyls (PCBs), polychlorinated dibenzo-p-dioxins (PCDDs) also known as polychlorinated oxanthrenes, polychlorinated dibenzofurans (PCDFs) and polycyclic aromatic hydrocarbons (PAHs) in indoor air. In the case of indoor air measurements, the careful planning of sampling and the entire measurement strategy are of particular significance since the result of the measurement may have far-reaching consequences, e.g. with respect to the need for remedial action or the success of such an action.
An inappropriate measurement strategy may contribute more overall uncertainty to the measurement result than the measurement procedure itself.

ISO 3826-3:2006 specifies requirements, including performance requirements, for integrated features on plastic, collapsible, non-vented, sterile containers (blood bag systems).
The integrated features refer to:
leucocyte filter;
pre-donation sampling device;
top and bottom bag;
platelet storage bag;
needle stick protection device.
In addition to ISO 3826-1:2003, which specifies the requirements of conventional containers, ISO 3826-3:2006 specifies additional requirements for blood bag systems using multiple units.
Unless otherwise specified, all tests specified in ISO 3826-3:2006 apply to the plastic container as prepared ready for use.

ISO 16000-7:2007 specifies procedures to be used in planning of air measurements to determine the concentrations of asbestos in indoor atmospheres. Careful planning of the measurement strategy is important, because the results can become the basis of recommendations for major building renovations, or for the return of a building to normal occupancy status after removal of asbestos-containing materials.
ISO 16000-7:2007 uses the following definition for indoor environments as specified in ISO 16000-1: dwellings having living rooms, bedrooms, do-it-yourself (DIY) rooms, recreation rooms, cellars, kitchens and bathrooms; workrooms or workplaces in buildings which are not subject to health and safety inspections in regard to air pollutants (for example, offices and sales premises); public and commercial buildings (for example, hospitals, schools, kindergartens, sports halls, libraries, restaurants and bars, theatres and other function rooms); cabins of vehicles and public transport.

ISO 13295:2007 specifies the requirements, the packaging and marking characteristics for mandrels suitable for discs and polishers used in dentistry.
ISO 13295:2007 uses the system of coding laid down in ISO 6360, which specifies a 15-digit number for the identification of dental rotary instruments of all types.

ISO 15181-3:2007 specifies the apparatus and analytical method for determining the amount of zineb that has been released from an antifouling paint into artificial seawater in accordance with the procedure given in ISO 15181-1.
Zineb is released from antifouling paints in the form of ionic ethylene-bis(dithiocarbamate) which is unstable in the marine environment. This part of ISO 15181 describes a method for converting the released species into a stable degradation product, ethylenethiourea, and determining its concentration in the treated artificial seawater samples, and gives the final calculation for the release rate of zineb under the specified laboratory conditions.
This part of ISO 15181 is designed to generally allow the concurrent determination of zineb and other biocides that can be released by a given antifouling paint (for example, copper) through the analysis of separate sub-samples of an artificial seawater extract generated in accordance with the procedure given in ISO 15181-1.
When used in conjunction with ISO 15181-1, the practical limits on the quantitative measurement of release rates by this method are from 2,9 micrograms per square centimetre per day to 500 micrograms per square centimetre per day. The quantitative measurement of release rates below this range will require the use of an analytical method with a lower limit of quantitation for ethylenethiourea.

ISO 16000-5:2007 is intended as an aid to planning volatile organic compound (VOC) indoor pollution measurements. In the case of indoor air measurements, the careful planning of sampling and the entire measurement strategy are of particular significance since the result of the measurement may have far-reaching consequences, for example, with regard to the need for remedial action or the success of such an action.
An inappropriate measurement strategy may contribute to the complete uncertainty of the measurement result in a larger extent than the measurement procedure itself.

ISO 1269:2006 specifies two methods for determining the volatile matter (including water) in homopolymer and copolymer resins of vinyl chloride.

ISO 13503-4:2006 provides for consistent methodology to measure fluid loss of stimulation and gravelpack fluid under static conditions. However, the procedure in ISO 13503-4:2006 excludes fluids that react with porous media.

ISO 5350-2:2006 specifies a method for the estimation by transmitted light of the visible dirt and shives in pulp manufactured in sheets. It does not apply to unbleached kraft pulps or to any other sheeted pulps that are too opaque to allow for the estimation of the minimum size or for minimum contrast specks to be counted, in accordance with ISO 5350-2:2006. The maximum grammage for most pulp sheets is in the range 800 g/m2 to 1 000 g/m2.
If the sheets of the mill sheeted pulp have high grammage or are very opaque for other reasons, ISO 5350-1:2006 should be applied.
ISO 5350-2:2006 is not intended for recycled pulp.

ISO 5350-1:2006 specifies a method for the estimation by transmitted light of the visible dirt and shives in laboratory sheets prepared from pulp. It is, in principle, applicable to all kinds of pulp, although it is mainly intended for pulp that is not manufactured in sheet form.
ISO 5350-1:2006 can also be applied to mill sheeted pulp, if the sheets have high grammage or are very opaque for other reasons, in which case ISO 5350-2:2006 is not applicable.
ISO 5350-1:2006 is not intended for recycled pulp.

ISO 13503-5:2006 provides standard testing procedures for evaluating proppants used in hydraulic fracturing and gravel packing operations. ISO 13503-5:2006 provides a consistent methodology for testing performed on hydraulic fracturing and/or gravel packing proppants. The "proppants" mentioned henceforth in this part of ISO 13503-5:2006 refer to sand, ceramic media, resin-coated proppants, gravel packing media, and other materials used for hydraulic fracturing and gravel-packing operations.
ISO 13503-5:2006 is not applicable for use in obtaining absolute values of proppant pack conductivities under downhole reservoir conditions.

ISO 14880-3:2006 specifies methods for testing optical properties, other than wavefront aberrations, of microlenses in microlens arrays. It is applicable to microlens arrays with very small lenses formed on one or more surfaces of a common substrate and to graded index microlenses.

ISO 14880-4:2006 specifies methods for testing geometrical properties of microlenses in microlens arrays. It is applicable to microlens arrays with very small lenses formed on one or more surfaces of a common substrate and to graded index microlenses.

ISO 16472:2006 specifies methods for the determination of amylase-treated neutral detergent insoluble fibrous residue content in all types of animal feed.
It includes a gravimetric routine method and a reference method.

2009-07-22 EMA: This amendment will be incorporate into a new edition of EN ISO 286-2 (00290149).

ISO 14005:2010 provides guidance for all organizations, but particularly small- and medium-sized enterprises, on the phased development, implementation, maintenance and improvement of an environmental management system. It also includes advice on the integration and use of environmental performance evaluation techniques.
ISO 14005:2010 is applicable to any organization, regardless of its level of development, the nature of the activities undertaken or the location at which they occur.

ISO 17678|IDF 202:2010 specifies a reference method for the determination of milk fat purity using gas chromatographic analysis of triglycerides. Both vegetable fats and animal fats such as beef tallow and lard can be detected. By using defined triglyceride equations, the integrity of milk fat is determined.
Basically, the method applies to bulk milk, or products made thereof, irrespective of feeding, breed or lactation conditions. In particular, the method is applicable to fat extracted from milk products purporting to contain pure milk fat with unchanged composition, such as butter, cream, milk, and milk powder.
However, under the circumstances listed hereafter, a false positive result can be obtained. Hence, the method is not applicable to milk fat: a) obtained from bovine milk other than cow's milk; b) obtained from single cows; c) obtained from cows which received an exceptionally high feeding of pure vegetable oils such as rapeseed oil; d) obtained from colostrum; e) subjected to technological treatment such as removal of cholesterol or fractionation; f) obtained from skim milk or buttermilk; g) extracted by using the Gerber, Weibull–Berntrop or Schmid–Bondzynski–Ratzlaff methods, or that has been isolated using detergents (e.g. the Bureau of Dairy Industries method).
With the extraction methods specified in g), substantial quantities of partial glycerides or phospholipids can pass into the fat phase. Consequently, the scope of ISO 17678|IDF 202:2010 excludes certain products and particularly cheese, whose ripening process can also affect the fat composition to such a degree that a false positive result is obtained.

ISO 3405:2011 specifies a laboratory test method, utilizing either manual or automated equipment, for determining the distillation characteristics of light and middle distillates derived from petroleum and having initial boiling points above 0 °C and end points below approximately 400 °C.

ISO 18472:2006 specifies the requirements for test equipment to be used to test chemical and biological indicators for steam, ethylene oxide, dry heat and vaporized hydrogen peroxide processes for conformity to the requirements given in ISO 11140-1 for chemical indicators, or the requirements given in the ISO 11138 series for biological indicators. ISO 18472:2006 also provides informative methods useful in characterizing the performance of biological and chemical indicators for intended use and for routine quality control testing.

ISO 23251:2006 is applicable to pressure-relieving and vapour-depressuring systems. Although intended for use primarily in oil refineries, it is also applicable to petrochemical facilities, gas plants, liquefied natural gas (LNG) facilities and oil and gas production facilities. The information provided is designed to aid in the selection of the system that is most appropriate for the risks and circumstances involved in various installations. ISO 23251:2006 is intended to supplement the practices set forth in ISO 4126 or API RP 520-1 for establishing a basis of design.
ISO 23251:2006 specifies requirements and gives guidelines for examining the principal causes of overpressure; and determining individual relieving rates; and selecting and designing disposal systems, including such component parts as piping, vessels, flares, and vent stacks.
ISO 23251:2006 does not apply to direct-fired steam boilers.

This International Standard specifies requirements and gives recommendations for the design, materials, construction, testing, operation, maintenance and abandonment of pipeline systems used for transportation in the petroleum and natural gas industries.
It applies to pipeline systems on land and offshore, connecting wells, production plants, process plants, refineries and storage facilities, including any section of a pipeline constructed within the boundaries of such facilities for the purpose of its connection. The extent of pipeline systems covered by this International Standard is illustrated in Figure 1.
This International Standard applies to rigid, metallic pipelines. It is not applicable for flexible pipelines or those constructed from other materials, such as glass-reinforced plastics.
This International Standard is applicable to all new pipeline systems and can be applied to modifications made to existing ones. It is not intended that it apply retroactively to existing pipeline systems.
It describes the functional requirements of pipeline systems and provides a basis for their safe design, construction, testing, operation, maintenance and abandonment.
On-land supply systems used by the gas supply industry excluding gas infrastructure from the input of gas into the on-shore transmission network up to the inlet connection of gas appliances are excluded from the scope of this standard.

ISO 11979-6:2007 specifies tests by which the shelf-life of sterile intraocular lenses (IOLs) in their final packaging can be determined. These tests include procedures to establish the stability of IOLs in distribution and storage.

ISO 11890-2:2006 is one of a series of standards dealing with the sampling and testing of paints, varnishes and related products.
It specifies a method for the determination of the volatile organic compound (VOC) content of paints, varnishes and their raw materials. ISO 11890-2 is preferred if the expected VOC content is greater than 0,1 % by mass and less than about 15 % by mass. When the VOC content is greater than about 15 % by mass, the less complicated method given in ISO 11890-1 may be used.
This method assumes that the volatile matter is either water or organic. However, other volatile inorganic compounds can be present and might need to be quantified by another suitable method and allowed for in the calculations.

ISO 14121-1:2007 establishes general principles intended to be used to meet the risk reduction objectives established in ISO 12100-1:2003, Clause 5. These principles of risk assessment bring together knowledge and experience of the design, use, incidents, accidents and harm related to machinery in order to assess the risks posed during the relevant phases of the life cycle of a machine.
ISO 14121-1:2007 provides guidance on the information that will be required to enable risk assessment to be carried out. Procedures are described for identifying hazards and estimating and evaluating risk. It also gives guidance on the making of decisions relating to the safety of machinery and on the type of documentation required to verify the risk assessment carried out.
It is not applicable to risks posed to domestic animals, property or the environment.

This part of En ISO 5350 specifies the method for the estimation by transmitted light of dirt and shives in pulp manufactured in sheets. It does not apply to unbleached kraft pulps or to any other sheeted pulps that are too opaque to allow for the estimation of the minimum size or for minimum contrast specks to be counted in accordance with this European Standard. The maximum grammage for most pulp sheets is in the range 800 g/m2 to 1000 g/m2. Part 1 of this European Standard deals with the estimation of dirt and shives in all kinds of pulp. It is based on inspection of laboratory sheets.

This Part of EN ISO 5350 specifies the method for the estimation by transmitted light of the visible dirt and shives in laboratory sheets prepared from pulp. It is applicable to all kinds of pulp, though it is mainly intended for pulp that is not manufactured in sheet form. Part 2 of this European Standard deals with the estimation of dirt and shives in mill sheeted pulp. This part can also be applied to mill sheeted pulp. If the sheets have high grammage or are very opaque for other reasons, in which case Part 2 is not applicable. This European Standard is not intended for recycled pulp.