CLC - European Committee for Electrotechnical Standardization

This part of IEC 62271 is applicable to prefabricated solid-insulation enclosed switchgear and controlgear assemblies designed for:
– alternating current;
– rated voltages above 1 kV and up to and including 52 kV;
– service frequencies up to and including 60 Hz;
– indoor installation;
– areas limited to authorized personnel.
The assembly can include either air-insulated or fluid-filled compartments, or both. For components installed in a solid-insulation enclosed switchgear and controlgear, this
document supplements or even replaces in some cases, the requirements as stated by the individual product standards.
The list of components which can be inside the solid-insulation enclosed switchgear and controlgear is not limited to the ones explicitly cited in this document.

This document specifies requirements and recommendations to maximize the sustainability of cabling systems including both customer premises infrastructure and the accommodation of information technology equipment by addressing the a) cabling design; b) selection, packaging and transportation of components and related materials; c) installation, operation and maintenance; d) management of waste materials; e) skill sets necessary for designers, installers and users.

IEC 62820‑1‑2:2026 specifies the technical requirements for the composition, functions, performance and test methods of building intercom systems using the Internet protocol (IP), and it is a supplement to IEC 62820‑1‑1. This document is applicable to the IP building intercom systems for both residential and commercial buildings.

This document specifies test methods for surface electromyography (sEMG) sensors by evaluating the quality of sEMG signals obtained from contracting the muscles of the forearm and hand for wearable applications. It is applicable to sEMG sensors that are used to decipher movement intentions and use them as control signals in situations such as virtual reality, game, unmanned aerial vehicles (UAV), robot control, and home automation. This document does not apply to sEMG sensors intended for medical diagnosis or treatment. For medical devices, national requirements can apply.

This part of IEC 63082 defines the concepts and terminology necessary to understand and communicate effectively about intelligent device management (IDM). This document explains the relationship between IDM and other existing asset management standards. Additionally, this document describes principles and defines organizational and functional structures associated with IDM. This document also introduces the concept of IDM program for coordination of multiple stakeholders.

This part of IEC 63287 specifies guidelines for a reliability qualification plan for power semiconductor modules to assure reliability targets over the entire product life.
Power semiconductor modules with incorporated control circuits are excluded. Clamped packages that need external pressure for being mounted in a system are excluded, e.g. disctype pressure pack devices.
This document is not intended for medical, military, aeronautics and astronautics-related applications.
NOTE Throughout the document, the term power semiconductor module refers to multichip semiconductor power modules as defined in 3.3.

IEC 60127-4:2026 relates to universal modular fuse-links (UMF) for printed circuits and other substrate systems, used for the protection of electric appliances, electronic equipment, and component parts thereof, normally intended to be used indoors. It does not apply to fuse-links for appliances intended to be used under special conditions, such as in a corrosive or explosive atmosphere. These fuses are normally intended to be mounted or replaced only by appropriately skilled persons using specialized equipment. This document applies in addition to the requirements of IEC 60127-1. The objectives of this part of IEC 60127 are as given in IEC 60127-1, with the additional requirement of a degree of non-interchangeability. This fourth edition cancels and replaces the third edition published in 2005, Amendment 1:2008 and Amendment 2:2012. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) align to IEC 60127-1:2023, third edition; b) enhance the rated current of UMFs to 100A and provide the corresponding maximum voltage drop and maximum sustained dissipation; c) modify the figures; d) update the normative references to the latest version. This International Standard is to be used in conjunction with IEC 60127-1:2023

This document specifies test methods for the determination of the efficiency of frequency conversion from the electrical input, and of the available and workload microwave output power in industrial microwave heating installations, as well as operational flexibility.
This document is in principle applicable to industrial microwave heating equipment and installations in the frequency range from 300 MHz to 300 GHz but focussed on the microwave ISM frequencies below 6 GHz.
This document relates to industrial microwave heating equipment operating as intended by the manufacturer's specifications for normal operation.
This document does not apply to appliances for household and similar use (covered by IEC 60335-2-25 [1]1), commercial use (covered by IEC 60335-2-90 [2] and IEC 60335-2-110 [3]) or laboratory use (covered by IEC 61010-2-010 [4]).

In addition to the requirements of IEC 61326-1, this part of IEC 61326 specifies the EMC test requirements for process automation equipment using at least one Ethernet-APL (Ethernet ADVANCED PHYSICAL LAYER) compliant port according IEC TS 63444. The type of equipment covered by this document includes INFRASTRUCTURE DEVICES such as switches as well as measurement and control devices. This document provides requirements for the EMC test setups of the APL interface for devices intended for use in process control and process measurement. The other functions of the equipment remain covered by other parts of the IEC 61326 series. NOTE Ethernet-APL uses IEEE Std. 802.3-2022 Ethernet Physical Layer 10BASE-T1L, suitable to be used for full- duplex communication over a single balanced pair of conductors. The test levels are based on the intended environment as stated in the product’s specification or user documentation and selected appropriately from IEC 61326-1.

IEC 61400-40:2026 provides the EMC requirements and test methods that apply to the individual wind turbine and all the sub systems which are part of the wind turbine. The current document applies to measurements on individual wind turbines and not multiple wind turbines. This document defines the requirements and test methods for the verification of the wind turbine performance against radiated emissions and the immunity of their components against conducted and radiated phenomena. This document is applicable to onshore and offshore wind turbines.

This document specifies test methods for the determination of useful high frequency power output in equipment for industrial heating and processing of materials. It is in particular applicable to HF generators made available to users as separate units.
This document is basically applicable to equipment operating in the frequency range 100 kHz to 300 MHz, as defined in IEC 60519-1, with the following limitations.
– This document does not apply to induction heating, which it is possible to carry out in the lower part of the specified frequency band.
– The ISM centre frequencies for dielectric heating and processing of industrial interest are narrow bands about 6,78 MHz, 13,56 MHz, 27,12 MHz and 40,68 MHz.
– This document is not applicable to:
• appliances for household and similar use;
• commercial use;
• laboratory use;
• medical high frequency equipment.
For equipment working in designated ISM bands, it is a legal requirement that the frequency remains within the ISM bands according to CISPR 11, but the resonant frequency of the circuit varies with the change of dielectric parameters of the load. Therefore, the value of the mean output power in the work cycle can be much lower than the value obtained under the test conditions. This value depends upon the response of the tuning system.
NOTE 1 The following criteria are suitable for determination of the classification as industrial equipment:
– commercial equipment is typically designed and planned for series production of many identical units;
– industrial equipment is typically produced in small series or even as single units; the processed goods are consumed or ready for final use at the end of the heating process.
NOTE 2 Heating a workload with dielectric parameters which change significantly in time and/or with temperature, the value of the output power obtained with the actual charge can be different from that obtained with the test load specified in this document.
This document relates to equipment normally operating under continuous rated conditions.

IEC 60086-2-1:2026 is applicable to primary batteries which are based on standardised electrochemical systems using aqueous electrolytes. It specifies: - the physical dimensions, - the discharge test conditions and discharge performance requirements. IEC 60086-2-1: 2026 cancels and replaces the fourteenth edition of IEC 60086 2 published in 2021. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) separation of lithium batteries into IEC 60086-2-2: Physical and electrical specifications; b) in Clause 3, terms were reordered according to their functions: electrochemical systems, electrical characteristics and specifications; c) TR03 and TR6 were added in Category 1, Round batteries; d) load of digital audio test for LR03, TR03 and R03 was changed from 50 mA to 75 mA and MAD was modified; e) personal grooming test of LR6 was added instead of high drain application test; f) high drain application test was added for TR6; g) radio /clock /remote control test was added for R6S; h) CD, digital audio, wireless gaming and accessories test was removed for LR6, R6P and R6S; i) 4,5 V of common designation was added for 3LR12, 3R12P and 3R12S; j) Annex D for common designation of IEC 60086 2:2021 was moved to IEC 60086 1:2026, as Annex H; k) Annex E for Compliance checklist of IEC 60086 2:2021 was removed and merged into Annex J of IEC 60086 1:2026.

IEC 60086-2-2:2026 is applicable to primary batteries which are based on standardised lithium (non-aqueous) electrochemical systems. It specifies: - the physical dimensions, - the discharge test conditions and discharge performance requirements. This first edition cancels and replaces the fourteenth edition of IEC 60086-2 published in 2021. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) separation of batteries with aqueous electrolyte into a separate Part 2-1: Physical and electrical specifications; b) maximum open circuit voltage of FR10G445 and FR14505 was changed from 1,83 to 1,90 V; c) load of digital audio test for FR10G445 was changed from 50 mA to 75 mA and MAD was modified; d) portable lighting test was added for FR10G445; e) motor/toy and radio /clock /remote control test was added for FR14505; f) in Clause 3, terms were reordered according their functions: electrochemical systems, electrochemical systems, electrical characteristics and specifications; g) Annex D for common designation of IEC 60086 2:2021 was moved to IEC 60086 1:2026, as Annex H; h) Annex E for Compliance checklist of IEC 60086 2:2021 was removed and merged into Annex J of IEC 60086 1:2026.

This part of IEC 61850 specifies the logical node classes for use in the domain of hydroelectric power stations, steam and gas turbines.
This IEC61850 domain information model standard utilizes the existing Logical Node (LN) classes defined in IEC 61850-7-4, Basic communication structure – Compatible logical node classes and data object classes where possible, while defining new and extended domain specific LN classes to provide the necessary data objects for application to functions and systems in the domain of hydroelectric power stations, steam and gas turbines. The domain information model includes the interface towards a central operator centre’s control functions.
The Scope of this document, related to steam and gas turbine specifics, is limited to overall control functions and generator and turbine control functions. For hydroelectric power, the scope includes the entire power station automation system.
Edition 3 is intended to form a basis for extensions in local implementations. Such extensions may be defined in profiles. Many of the Logical Nodes defined in this document are designed to be suitable for use in domains beyond the scope of hydro power plants and steam and gas turbines. A suggested structure of the Logical Nodes into packages for integration with other domains is provided in Annex G (informative), Migration of this document to the future edition of IEC 61850.

This part of IEC 62228 specifies test and measurement methods for the EMC evaluation of CXPI transceiver ICs under network condition. It defines test configurations, test conditions, test signals, failure criteria, test procedures, test setups and test boards. This specification is applicable for standard CXPI transceiver ICs and ICs with embedded CXPI transceiver and covers
– the emission of RF disturbances;
– the immunity against RF disturbances;
– the immunity against impulses;
– the immunity against electrostatic discharges (ESD).

This part of IEC 61300 describes a method for measuring the endface geometry of rectangular multifibre ferrules having an IEC defined optical interface. The primary attributes are fibre position relative to the endface, endface angle relative to the guide holes, fibre tip radii and core dip for multimode fibres.

This document specifies the requirements for testing items of equipment intended for use on railway vehicles which are subsequently subjected to vibrations and shock owing to the nature of railway operational environment. To gain assurance that the quality of the equipment is acceptable, it is exposed to tests of reasonable duration that simulate the service conditions seen throughout its expected life.
Simulated long-life testing can be achieved in a number of ways each having their associated advantages and disadvantages, the following being the most common:
a) amplification: where the amplitudes are increased and the time base decreased;
b) time compression: where the amplitude history is retained and the time base is decreased (increase of the frequency);
c) decimation: where time slices of the historical data are removed when the amplitudes are below a specified threshold value.
The amplification method as stated in item a) above, is used in this document and together with the publications referred to in Clause 2; it defines the default test procedure to be followed when vibration testing items for use on railway vehicles.
Whilst this document is primarily concerned with railway vehicles on fixed rail systems, its wider use is not precluded. For systems operating on pneumatic tyres, or other transportation systems such as trolleybuses, where the level of shock and vibration clearly differ from those obtained on fixed rail systems, specific test levels can be considered. In that case, the frequency spectra and the shock duration and amplitude are computed in compliance with the guidelines in Annex A.
Annex F provides the functional random vibration load that can be considered by the user for urban vehicles operating on pneumatic tyres.
This document applies to single axis testing. However, multi-axis testing is possible.
The anchoring bolts at the fixing point(s) of the equipment are not evaluated in this document.
This document is intended to evaluate equipment which is attached to the main structure of the vehicle (and components mounted thereon). It is not intended to test equipment which forms part of the main structure. Main structure in the sense of this document means car body, bogie and axle.
The following items are out of scope of this document:
– the traction motors for railway vehicles;
– any mechanical substructure not equipped with electrical, electronic or pneumatic component.
Additional or special vibration tests for some specific equipment are not specified in this document, for example:
a) equipment mounted on, or linked to, items which are known to produce defined frequency excitation;
b) equipment such as pantographs, shoegear, or suspension components which are known to be exposed to specific shock and vibration excitation;
c) equipment intended for use in special operational environments as specified by the customer;
d) transportation and handling tests.

This part of IEC 61300 evaluates the effects of a number of successive cycles of mating and un-mating of fibre optic connectors or other interconnecting devices on optical performance and mechanical degradation of the component under normal usage conditions.

This document specifies requirements, recommendations, and examples for implementing a risk-informed decision-making (RIDM) process for managing existing network assets in power systems. The intended audience concerns power network organizations' stakeholders and decision makers, such as asset managers, risk managers, regulators, asset owners, and service providers. The RIDM process details the steps to ensure transparency, consistency, and traceability of the decision by:
– specifying the risk decision-making context depending on asset management objectives, available knowledge, and risk stakeholders' concerns;
– identifying the appropriate risk management strategies and the knowledge supporting the analyses;
– detailing the essential steps for conducting a risk analysis and justifying investments, regardless of the calculation methods used;
– providing essential information and warnings to decision makers;
– implementing performance evaluation and continuous improvement.
The document is based on the asset management principles from ISO 55000:2024 [1] and is aligned with ISO 55001:2024 [2]. Compliance with the requirements of this document is independent of compliance with ISO 55001:2024 [2].

IEC 60076-4:2026 applies to lightning and switching impulse tests on power transformers and reactors. Information is given on waveforms, test circuits including test connections, earthing practices, failure detection methods, test procedures, measuring techniques and interpretation of results.

IEC 62475:2026 is applicable to high-current testing and measurements on both high-voltage and low-voltage equipment. It deals with steady-state and short-time direct current (as e.g. encountered in high-power DC testing), steady-state and short-time alternating current (as e.g. encountered in high-power AC testing), and impulse-current. In general, currents above 100 A are considered in this International Standard, although currents less than this can occur in tests. This standard: • defines the terms used; • defines parameters and their tolerances; • describes methods to estimate uncertainties of high-current measurements; • states the requirements applicable to a complete measuring system; • describes the methods for approving a measuring system and checking its components; • describes the procedure by which the user shows that a measuring system meets the requirements of this document, including limits set for uncertainty of measurement. This standard also covers fault detection during, for example, lightning impulse testing. This second edition cancels and replaces the first edition published in 2010. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: • minor errors in edition 1 have corrected; • terms and definitions have been modified to achieve best possible adherence to IEC 60060‑2:2025 and have been ascribed appropriate [SOURCE]; • terms and definitions which in edition 1 were presented in clauses other than Clause 3 have been moved into Clause 3. • Annex B, Clause B.4 has been amended to provide an example of uncertainty calculation for the use of an approved measuring system; • Clause C.2 has been deleted since the definitions given there are not referred to, with the exception of the origin of the step, which is used in Annex D. The applicable information has been added to Annex D as Note 1. • Annex G, Clause G.8 has been amended to replace “peak factor” by “a factor”. Texts have been clarified. Equations for relation between factor κ and cos ϕ have been developed to a simplified form. • Annex G, Clause G.9 has been added.

This European Standard deals with the safety of microwave appliances intended for commercial use, their rated voltage being not more than 250 V for single-phase appliances connected between one phase and neutral and 480 V for other appliances.

This European standard deals with the safety of electrically operated commercial rinsing sinks used in commercial kitchens, their rated voltage being not more than 250 V for single-phase appliances connected between one phase and neutral, and 480 V for other appliances

This European Standard deals with the safety of microwave appliances intended for commercial use, their rated voltage being not more than 250 V for single-phase appliances connected between one phase and neutral and 480 V for other appliances.

This European standard deals with the safety of electric commercial amusement machines and personal service machines, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances, including direct current (DC) supplied appliances and battery-operated appliances

This European Standard deals with the safety of electric vaporizers for household and similar use, their rated voltage being not more than 250 V including direct current (DC) supplied appliances and battery-operated appliances

This European Standard deals with the safety of electric ondol-mattresses for household and similar purposes, their rated voltage being not more than 250 V including direct current (DC) supplied appliances and battery-operated appliances. This standard also applies to control units supplied with the appliance

This European Standard deals with the safety of electric ondol-mattresses for household and similar purposes, their rated voltage being not more than 250 V including direct current (DC) supplied appliances and battery-operated appliances. This standard also applies to control units supplied with the appliance

This European standard deals with the safety of electric commercial amusement machines and personal service machines, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances, including direct current (DC) supplied appliances and battery-operated appliances

This European Standard deals with the safety of electric vaporizers for household and similar use, their rated voltage being not more than 250 V including direct current (DC) supplied appliances and battery-operated appliances

This European standard deals with the safety of electrically operated commercial rinsing sinks used in commercial kitchens, their rated voltage being not more than 250 V for single-phase appliances connected between one phase and neutral, and 480 V for other appliances

This part of IEC 63522 is used for testing along with the appropriate severities and conditions for measurements and tests designed to assess the ability of DUTs to perform under expected conditions of transportation, storage and all aspects of operational use.
This document defines a standard test method for impulse voltage test.

2021-07-09 MDC: Negative assessment
2020-12-24: This prAB represents common mods to EN 62841-3-12:2019/prA1 (PR=73191) under parallel
D164/C043: DOW= DOR + 48 months

This document establishes general rules and safety requirements on the application of capacitors, resistors, inductors, and complete filter units for electromagnetic interference
suppression which will be connected to an AC mains or other supply (DC or AC) with a nominal voltage not exceeding 1 000 V AC having a nominal frequency not exceeding 400 Hz, or 1 500 V DC.
It facilitates drafters of product safety standards and other stakeholders such as designers, manufacturers, se rvice providers, policy makers and regulators to consider safety aspects for the intended use and the reasonably foreseeable misuse of these components in its products and systems and apply risk reduction measures to achieve a tolerable risk level.

This part of IEC 60794-1 describes test procedures used to establish uniform requirements for optical fibre cables for the environmental property - underwater cable resistance to hydrostatic pressure.
This document applies to optical fibre cables for use with telecommunication equipment and devices employing similar techniques, and to cables having a combination of both optical fibres and electrical conductors.
See IEC 60794-1-2 for a reference guide to test methods of all types and for general requirements.

Addition:
This document specifies the determination of airborne acoustical noise of mains operated and cordless dry vacuum cleaners including their accessories and docking stations for household use or under conditions similar to those in households.
For wet and dry vacuum cleaners, the dry cleaning function applies. The wet cleaning function is measured in accordance with IEC 60704-2-20.
NOTE 101 Particular requirements for floor cleaning robots are specified in IEC 60704-2-171.
This document describes the determination of the noise emission of dry vacuum cleaners under normal operating conditions on carpet and hard floor in accordance with IEC 62885-2:—,4.62.

This part of IEC 61760 defines requirements for component specifications of electronic components that are intended for usage in surface mounting technology. To this end, it specifies a reference set of process conditions and related test conditions to be considered when compiling component specifications.
The objective of this document is to ensure that a wide variety of SMDs can be subjected to the same placement, mounting and subsequent processes (e.g. cleaning, inspection) during assembly. This document defines tests and requirements that are included in any SMD component’s general, sectional or detail specification. In addition, this document provides component users and manufacturers with a reference set of typical process conditions used in surface mounting technology.
Some of the requirements for component specifications in this document are also applicable to components with leads intended for mounting on a circuit board, including solderless interconnection technology. Cases for which this is appropriate are indicated in the relevant subclauses.
NOTE Solderless interconnection technology refers to a mounting method which is not part of the surface-mounting process and the components do not undergo a soldering operation. Such components are included in this document because the mounting of components for solderless interconnection commonly occurs after the mounting of SMDs.

IEC 60127-7:2026 covers requirements for miniature fuse-links for special applications. This part of IEC 60127 is applicable to fuse-links with a rated voltage not exceeding 1 000 V, a rated current not exceeding 125 A and a rated breaking capacity not exceeding 50 kA. It does not apply to fuses completely covered by the subsequent parts of IEC 60269-1. It does not apply to miniature fuse-links for appliances intended to be used under special conditions, such as in corrosive or explosive atmospheres.

This document specifies three techniques for the determination of free Bisphenol A (BPA) in plastics of electrotechnical products.
This document describes the use of liquid chromatography–diode array detector (LC-DAD), liquid chromatography mass spectrometry (LC-MS), liquid chromatography tandem mass spectrometry (LC-MS/MS) with these test methods detailed in Annex A and Annex B.
These test methods have been evaluated for use with PC, PC/ABS, PP matrices containing free BPA between 20 mg/kg to 500 mg/kg as shown in the Pre-IIS 13 results in Annex C and IIS 13 results in Annex D [1], [2]. The use of these methods for BPA concentration ranges of plastics, other than those specified in Annex C and Annex D, has not been evaluated.
This document is a basic environment horizontal publication focusing on test methods and is primarily intended for use by committees in the preparation of publications within the area of environment in accordance with the principles laid down in IEC Guide 123. Wherever applicable, it is the responsibility of committees to make use of environment basic publications in the preparation of their environment group and product publications. Committees can apply this document directly to products when they do not develop a product publication in the area of environment.
WARNING – Persons using this document should be familiar with normal laboratory practice. This document does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate safety and health practices and to ensure compliance with any national regulatory conditions.