SIST - Slovenian Institute for Standardization

1.1   General
This document is applicable to food depositors as listed in 1.2 and the equipment typically integrated with them, i.e. product pumps, product elevators, conveyors and indexing mechanisms, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex B).
This document deals with the significant hazards, hazardous situations and events during transport, assembly and installation, commissioning, use, decommissioning, disabling, dismantling and scrapping.
NOTE 1   According to the clause which is referred to, "use" includes "setting, teaching/programming or process changeover, operation, cleaning, fault finding and maintenance".
NOTE 2   Although this document is intended to apply to depositors used in the food industry, many of its requirements can also be used for the same or similar machines used in other industries.
This document does not apply to the following machines:
- auger depositors or auger fillers and gravimetric filling machines; safety requirements for these machines are contained in EN 415-3;
- automatic dough dividers, safety requirements for these machines are contained in EN 12042;
- filling machines for sausages, safety requirements for these machines are contained in EN 12463;
- mincing machines, safety requirements for these machines are contained in EN 12331;
- food depositors that are powered exclusively by manual effort;
- roller depositors intended for use in craft bakeries. Safety requirements for these machines are in EN 17677.
This document does not deal with the following hazards:
- hazards related to the use of food depositors in a potentially explosive atmosphere;
- hazards that can arise from using a food depositor to deposit a non-food product.
This document is not applicable to food depositors that were manufactured before the date of its publication as a European Standard.
1.2   Types of food depositors
1.2.1   General
This document deals with five different types of food depositor. The component parts of each of the different types of depositor are labelled in the figures shown in Clause 4 of this document.
1.2.2   Piston depositor
A piston depositor typically comprises a hopper, a rotary valve, a product measuring chamber in the form of a piston and a product dispensing valve. Some piston depositors incorporate several product measuring chambers and dispensing valves. Some designs dispense the product directly from the rotary valve without the use of a separate product dispensing valve. The volume of product dispensed is varied by altering the stroke of the product measuring chamber piston. Piston depositors are used to fill liquids, liquids containing solids in suspension and pastes. The product dispensing valve can be attached rigidly to the depositor or using a flexible pipe and in some cases is held by the operator. Figure 1 shows the typical cross section of a piston depositor.
Figure 1 - Piston depositor
1.2.3   Chamber depositor
A chamber depositor comprises a hopper feeding one or more product measuring chambers that are filled under gravity from the top. When the chamber has been filled with product the flow of product is stopped either by moving the chamber or using a product cutting device. The product is then discharged through the bottom of the chamber either by moving the chamber or by moving a plate in the base of the chamber. The volume of product dispensed is varied by altering the volume of the chamber. Chamber depositors are typically used to deposit free-flowing products like cooked rice or pasta. Figure 2 shows the typical cross section of a chamber depositor.
Figure 2 - Chamber depositor
1.2.4   Roller depositor
A roller depositor typically comprises a hopper that feeds product to two or more fluted contra-rotating rollers. These rollers force the product through one or more dies that shape the product.
...

This document specifies two accelerated corrosion test methods. These methods assess the corrosion resistance of products containing copper in environments where there is a significant influence of chloride ions, mainly as sodium chloride from a marine source or winter road de-icing salt, as well as the influence of corrosion-promoting gases from industrial or traffic air pollution.
This document specifies both the test apparatus and test procedures to be used in executing the accelerated corrosion tests.
The methods are especially suitable for assessing the corrosion resistance of sensitive products with metals, e.g. electronic components, used in traffic and industrial environments.

This document specifies the most important design and metrological characteristics of two-point inside micrometers:
—    with a scale interval or digital step of 0,001 mm and 0,01 mm;
—    with analogue or digital indication.
This document is applicable to two-point inside micrometers with and without interchangeable extensions.
This document does not apply to micrometers fitted with a dial gauge, or to jaw micrometers.

This document specifies three methods for the determination of the ash of poly(vinyl chloride).
The general procedures given in ISO 3451-1 are followed. For ash, method A is used. For sulfated ash, methods B and C are used. All three methods are applicable to resins, compounds and finished products. Methods B and C are applicable when lead-containing compounds are present.

This document specifies the requirements relating to:
Aluminium alloy AL-P2014A
T6 or T62
Clad sheets and strips
0,4 mm ≤ a ≤ 6 mm
for aerospace applications.

This document specifies the requirements for washer-disinfectors (WD) intended to be used for the cleaning and chemical disinfection, in a single operating cycle, of reusable items such as:
a)       bed frames;
b)       bedside tables;
c)        transport carts;
d)       containers;
e)       surgical tables;
f)         sterilization containers;
g)       surgical clogs;
h)       wheelchairs;
i)         aids for persons with disabilities.
This document also specifies the performance requirements for the cleaning and disinfection of the WD and its components and accessories.
Devices identified within the scopes of ISO 15883-2, ISO 15883-3, ISO 15883-4, and ISO 15883-6 do not fall within the scope of this document.
In addition, this document specifies the methods for type testing, works testing, validation (installation, operation, and performance qualification on first installation), routine control, and monitoring, as well as requalifications to be carried out periodically and after essential repairs.
NOTE 1        WD covered by this document can also be used for cleaning and chemical disinfection of other thermolabile and reusable devices as recommended in the instructions for use (IFU) for those devices.
NOTE 2        The performance requirements specified in this document cannot ensure the inactivation or removal of the causative agent(s) (prion proteins) of transmissible spongiform encephalopathies.

IEC 62282-3-202:2025 provides performance test methods specialized for the thermal and electrical characteristics of an energy management system to effectively share the heat and power of networked small stationary fuel cell power systems. These test methods are applied for each small stationary fuel cell power system. This document covers small stationary fuel cell power systems which can be complemented with a supplementary heat generator or a thermal storage system, or both, such as:
- output: rated electric power output of less than 10 kW for each system;
- output mode: grid-connected or independent operation or stand-alone operation with alternating current (AC) output not exceeding 240 V or direct current (DC) output;
- operating pressure: maximum allowable working pressure of less than 0,1 MPa (G) for the fuel and oxidant passages;
- fuel: gaseous fuel (natural gas, liquefied petroleum gas, propane, butane, hydrogen) or liquid fuel (kerosene, methanol); oxidant: air.
This document does not apply to small stationary fuel cell power systems with electricity storage other than (small scale) back-up power for safety, monitoring and control.

This document specifies the requirements for the effective control of non-deliverable software. This document can be used during the design, development, test, production, release, use, maintenance, and retirement of non-deliverable software. This can include non-deliverable software procured from external suppliers and utilized in the design, production, evaluation, test, acceptance, or calibration of a deliverable product.
This document focuses solely on the unique requirements of the operational processes that pertain to non-deliverable software as identified below:
This document applies to non-deliverable software (including firmware) that affects a deliverable product or service. Following are several applications and supporting examples of non-deliverable software that is within the scope of this document:
—   design and development: modelling, simulation, virtual reality, virtual machine, computer-aided design (CAD), three-dimensional (3D) modelling and analysis tools, software compiler, and code generators;
—   manufacturing: additive manufacturing, computer numerical controlled (CNC) programs, robotics, factory automation, tools that load deliverable software, software used in special process (e.g. heat treat, shot peen, sonic wall inspection), and automated manufacturing software (i.e. pick and place);
—   verification, validation and maintenance: coordinate measuring machine (CMM) programs, hardware or software qualification, code coverage, test scripts, analysis tools, acceptance test, production acceptance, calibration (inspection, test or calibration), simulator, emulator, and software used in post-delivery service provisions.
The following types of software are not within scope of this document:
—   deliverable software (refer to EN 9115);
—   manufacturing and measuring equipment embedded software (e.g. operating system, drivers);
—   enterprise or office software (e.g. MS Office, word processing or spreadsheet applications, Teams, network software, email, employee management system).
Operational processes not covered in this document are addressed by the respective organization’s quality management system (QMS), based on the EN 9100-series (i.e. EN 9100, EN 9110, EN 9120) and/or ISO 9001 standards.

This document specifies a method of determining the ability of elements of connection to withstand sinusoidal or random vibrations of specified severities.
It is used together with EN 2591-100.
This test is based on EN 60068-2-6 and EN 60068-2-64.

This document specifies the test methods to evaluate the performance of coaxial, quadrax and databus cables after the installation of plastic cable ties.
It is expected to be used together with EN 3475 100.

This document specifies the general characteristics, conditions for qualification, acceptance and quality assurance for a fibre optic cable with a 62,5 µm/125 µm simplex fibre, 2,74 mm outside cable diameter and of semi-loose construction. The basic construction is the cable specified in EN 4641-102 with added sheaths for ruggedized usages.

This document provides a data model and encoding rules for the use of radio frequency identification (RFID) tags for items appropriate for the needs of all types of libraries (including national, academic, public, corporate, special, and school libraries).
This document specifies the rules for encoding
— a subset of data elements taken from the total set of data elements listed in ISO 28560-1 into a basic block, and
— other data elements into extension blocks onto the RFID tag.
A source of additional information about implementation issues is provided in Annex A.

ISO/IEC 15459-1:2014 specifies a unique string of characters for the identification of individual transport units. The character string is intended to be represented in a bar code label or other AIDC media attached to the entity to meet management needs. To address management needs, different types of entities are recognized in the various parts of ISO/IEC 15459, which allows different requirements to be met by the identities associated with each type.
The rules for the unique identification for individual transport units, to identify physical logistical transfers, with the identity relevant for the duration of one or more items in the load being held or transported as part of that load, are defined and supported by example.

IEC 60255-27:2023 specifies the product safety requirements for measuring relays and protection equipment having a rated AC voltage up to 1 000 V, or a rated DC voltage up to 1 500 V. This document specifies essential safety requirements to minimize the risk of fire and hazards caused by electric shock or injury to the user and property. This document specifies only product safety requirements; functional performance of the equipment is not covered. This document covers all the ways in which the equipment can be mounted and used in cabinets, racks and panels. This document also applies to auxiliary devices such as shunts, series resistors, transformers, auxiliary control panels, display devices, etc., that are used in conjunction with measuring relays and protection equipment and are tested together.

This document specifies the dimensions, tolerances, required characteristics and the mass of an AWG 24 shielded quad cable, type KL, intended for high speed (100 Mbit/s) full duplex Ethernet networks.
Linked to this particular application, the operating temperatures of the cable are between −65 °C and 125 °C.
This cable is laser markable, this marking satisfies the requirements of EN 3838.
The characteristics impedance is 100 Ω ± 15 Ω.

This document defines the requirements for developing and documenting the goals, limitations, target end users and target patient population for artificial intelligence (AI) and augmented intelligence (AuI) enabled 2D radiograph analysis software for dentistry applications. It outlines the requirements for appropriate training data, validation data, test data and annotation for the software to ensure that it achieves its intended goals, and is restricted to the aspects. This document does not cover the specific implementation details, and focuses on static (i.e. non-dynamic) AI/AuI.

ISO/IEC 15459-4:2014 specifies a unique string of characters for the identification of individual products and product packages. The character string is intended to be represented in a linear bar code symbol or two-dimensional symbol or other automatic identification and data capture (AIDC) media attached to the entity to meet management needs. To address management needs, different classes of identities are recognized in the various parts of ISO/IEC 15459, which allows different requirements to be met by the identities associated with each class.  
The rules for the identification of an individual occurrence of a product or product package, understood to mean the layers zero and one defined in ISO 17367 and ISO 17366, respectively, are defined and supported by examples.

This document specifies requirements and recommendations for representing subject fields and concept relations in TBX-compliant terminological document instances. Examples in this document utilize the data category as attribute (DCA) style of TBX markup.

ISO/IEC 15459-5:2014 specifies a unique string of characters for the identification of individual returnable transport items (RTIs). The character string is intended to be represented in a bar code label or other automatic identification and data capture (AIDC) media attached to the item to meet management needs. To address management needs, different classes of identities are recognized in the various parts of ISO/IEC 15459, which allows different requirements to be met by the identities associated with each class.  
The rules for the identification of RTIs, with the identity being relevant for the complete lifecycle of the item, are defined and supported by example.

IEC 63522-36:2025 is used for testing all kinds of relays and evaluates their ability to perform under expected conditions of transportation, storage, and all aspects of operational use.
This document defines a standard test method to measure fire hazards of all materials susceptible to fire hazards.

ISO/IEC 15459-3:2014 specifies the common rules applicable for unique identification that are required to ensure full compatibility across different identities.

This document specifies an annotation language for visual information, based on VoxML (visual object concept structure modelling language), a modelling language for the visualizations of concepts and actions denoted by natural language (NL) expressions in three dimensions (3D).  
The specification of the VoxML-based annotation scheme conforms to the requirements given in ISO 24617-1, ISO 24617-7 and ISO 24617-14. The adoption of VoxML, specified in ISO 24617-14 as a semantic basis, is necessary for the 3D simulation and visualization of actions and motions taken by both human and artificial agents in real-life situations.

1   Scope
1.1   General
The aviation, space, and defence industries rely on the development and manufacture of complex products comprised of multiple systems, subsystems, and components each designed by individual designers (design activities) at various levels within the supply chain. Each design or manufacturing activity controls various aspects of the configuration and specifications related to the product. When a change to design or process is requested or required, the change is typically required to be evaluated against the impacts to the entire system.
Proposed changes to design data/information that the design activity identifies to be minor and have no effect on the product requirements or specifications, have the potential to be implemented and approved, where authorized to do so, but requires notification. Changes that affect customer mandated requirements or specifications shall be approved prior to implementation. In many cases, the design activity is not conducted by the DAH or design authority. The design activity may be several layers below the design approval. Irrespective of where the design activity is conducted in the supply chain, notification is required. The typical change notification flow is presented in Figure 1.
[Figure 1]
Submitting NOC data either electronically or conventionally on paper is subject to the terms and conditions of the customer’s contract. This also includes, where applicable, data access under the regulations of export control.
The process of exchanging, coordinating, and approving NOC data varies with the multiple relationships and agreements among all organizations concerned. An objective of this document is to provide the definition of a data set that can be integrated into any form of communication (e.g. electronic data interchange, submission of conventional paper forms). A sample form can be found in the Supply Chain Management Handbook (SCMH).
If all or part of this document is contractually invoked, design organizations and design holders (i.e. the organization responsible for the product end item design) that have responsibility for change management of products used on other higher-level designs shall use the information and processes defined in this document for submitting change notifications.
1.2   Application
This document defines the common NOC requirements for aviation, space, and defence organizations. The requirements that a design organization are to use when submitting a NOC to the customer for either change authorization or notification are included herein. A NOC informs the customer of physical or functional (e.g. design, material, software, maintenance) changes or any associated process changes to an established baseline configuration.
Retention of the NOC establishes a means of configuration control and captures the evolution of the part. This requirement is of utmost importance in commercial/civil aviation products where changes to type certificated products are mandated by regulations; however, these same concepts are also required in defence and space applications per contractual requirements.
Where there are changes to items which the organization does not have design input or is not permitted to make any changes to the design [e.g. build to print, Technical Standard Order (TSO) articles] then change requests are to be formally submitted to the customer and approved via the customer’s change request process.
[...]

This document specifies the general characteristics, conditions for qualification, acceptance and quality assurance for a fibre optic cable with a 62,5 µm/125 µm graded index fibre nominal, 1,8 mm outside diameter and of semi-loose buffer construction.

IEC 63522-25:2025 Used for testing along with the appropriate severities and conditions for measurements and tests designed to assess the ability of DUTs to perform under expected conditions of transportation, storage and all aspects of operational use.
This document defines a standard test method to check the magnetic interference between relays under operating conditions and their influence on other relays in the neighbourhood.

This document specifies the syntax, description and resolution functional components of the digital object identifier system. It specifies the general principles for the creation, registration and administration of DOI names (where DOI is an initialism for “digital object identifier”).
This document defines the syntax for a DOI name, which is used for the identification of an object of any material form (non-physical or physical) or an abstraction (such as a textual work) where there is a functional need to distinguish it from other objects.
The DOI name does not replace, nor is it an alternative for, an identifier used in another scheme, such as the schemes defined by ISO/TC 46/SC 9. This document describes how the DOI system can be used in conjunction with another identifier scheme (for example, to provide additional functionality, such as resolution, where this is not already available), and how the character string of that other scheme can be integrated into the DOI system through system metadata or the DOI syntax or both.
This document does not specify particular technologies to implement the syntax, description and resolution functional components of the digital object identifier system.

This document specifies requirements, recommendations, and guidance on aspects of accessible systems for living independently (ASLI) in relation to technical solutions, service design, provision, and information. This includes adapting design and functionality of systems, to allow ease of use by any user, regardless of their abilities.
This document does not cover system-to-system communication.
This document is not applicable to household and similar electrical appliances covered by EN IEC 63008 [10].

This document identifies the purpose and benefits of disposition and provides organizations with guidance about how to manage disposition-related processes. In particular, it:
— specifies responsibilities for records disposition processes;
— provides guidance on the key areas against which records disposition processes can be assessed;
— provides requirements and guidance for those implementing disposition processes; and
— provides guidance on how to integrate records disposition processes into an organization’s operations.

This document specifies a markup language called QuantML for annotating and representing semantic phenomena relating to quantification in natural language. QuantML comprises an extensible markup language (XML)-based representation format, an abstract syntax and a semantics.

1.1 General
This part of the IEC 60255 series specifies the requirements for electromagnetic compatibility for measuring relays and protection equipment. It is applicable to measuring relays and protection equipment and combinations of devices to form schemes for power system protection including the control, monitoring, communication and process interface equipment used with those systems.
Tests specified in this document are not required for equipment not incorporating electronic circuits, for example electromechanical relays.
The requirements specified in this document are applicable to measuring relays and protection equipment in a condition representative of how new equipment is provided by the manufacturer. All tests specified are type tests only.
1.2 Emission
This document specifies limits and test methods, for measuring relays and protection equipment in relation to electromagnetic emissions which might cause interference in other equipment.
These emission limits represent electromagnetic compatibility requirements and have been selected to ensure that the disturbances generated by measuring relays and protection equipment, operated normally in substations and power plants, do not exceed a specified level which could prevent other equipment from operating as intended.
Test requirements are specified for the enclosure, auxiliary power supply ports, input/output ports, signal/control ports and wired network ports.
1.3 Immunity
This document specifies the immunity test requirements for measuring relays and protection equipment in relation to continuous and transient, conducted and radiated disturbances, including electrostatic discharges.
These test requirements represent the electromagnetic compatibility immunity requirements and have been selected so as to ensure an adequate level of immunity for measuring relays and protection equipment, operated normally in substations and power plants.
NOTE 1 Product safety considerations are not covered in this document.
NOTE 2 In special cases, situations will arise where the levels of disturbance could exceed the levels specified in this document, for example where a hand-held transmitter or a mobile telephone is used close to measuring relays and protection equipment. In these instances, special precautions and procedures could have to be employed.

ISO/IEC 15459-6:2014 specifies a unique string of characters for the identification of groupings of products, product packages, transport units and items. The character string is intended to be represented in a linear bar code symbol and two-dimensional symbol or other automatic identification and data capture (AIDC) media attached to the entity to meet management needs and/or regulatory needs (e.g. customs clearance). To address these needs, different types of identifiers are recognized in the various parts of ISO/IEC 15459, which allows different requirements to be met by the unique identifiers associated within the context of the specific parts of ISO/IEC 15459.
The unique identifiers for grouping of products, product packages, transport units and items enables grouping by type, characteristics, order, manufacturing, quality, location, movement, etc. to be uniquely identified. It is possible to use with other unique individual identifiers defined in other parts of ISO/IEC 15459. Encoding these unique identifiers in a data carrier enables information about the item processing to be clearly identified.

This document specifies the required characteristics of repositories used for the long-term storage of archive and library materials. It covers the siting, construction and renovation of the storage facility, and the installation and equipment to be used both within and around the building.
This document applies to all archive and library materials held in repositories, where mixed media can be stored together with paper-based materials. It does not preclude the establishment of separate areas or compartments within individual repositories, where the environment can be controlled to create conditions suitable for the needs of specific archive materials.
This document does not specify exhibition or display guidelines.

IEC 63522-35:2025 is used for testing all kind of relays within the scope of technical committee 94 and evaluates their ability to perform under expected conditions of transportation, storage and all aspects of operational use.
This document defines a standard test method for resistance to cleaning solvents.

This document specifies methods for extracting candidate terms from text corpora and gives guidance on selecting relevant designations, definitions, concept relations and other terminology-related information.

This document specifies the International Standard name identifier (ISNI) for the identification of public identities of parties, i.e. the identities used publicly by parties involved throughout the media content industries in the creation, production, management and content distribution chains.
The ISNI system uniquely identifies public identities across multiple fields of creative activity and provides a tool for disambiguating public identities that might otherwise be confused.
The ISNI is not intended to provide direct access to comprehensive information about a public identity but can provide links to other systems where such information is held.

IEC 62902:2025 specifies methods for the clear identification of secondary cells, batteries, battery modules and monoblocs according to their chemistry (electrochemical storage technology).
The markings described in this document are applicable to
- secondary cells,
- batteries,
- battery modules, and
- monoblocs,
when they are placed on the market for end use and when their battery volume exceeds 900 cm3.
The chemistry marking is useful for the installation, operation and decommissioning phases in the battery's life cycle.
This document defines the conditions of use of the markings indicating the chemistry of these secondary batteries.

This document specifies a method to determine the resistance to internal pressure of polyethylene (PE), crosslinked polyethylene (PE-X) and unplasticized (PA-U) pipes to verify the condition of the pipe after being subjected to a squeeze-off procedure.
The equipment and procedure used to prepare the test samples and test parameters are given in this document, i.e.:
a)   the diameter and series of the pipe to be tested (see 6.1);
b)   the number of test pieces (see 6.2);
c)   the parameters for the hydrostatic strength tests (see 7.6).
NOTE 1   Further information on the squeeze-off procedure is given in EN 12007-2 and ISO/TS 10839 for polyethylene, and CEN/TS 12007-6 for unplasticized polyamide.
NOTE 2   The squeeze-off procedure is specified to limit gas flow to allow maintenance, repair or to make network connections. Squeeze-off is used in an emergency for pipes carrying other media.

This document specifies requirements for the installation of permanently installed liquefied petroleum gas (LPG) systems and LPG-burning appliances on small craft.
This document is applicable to portable cooking appliances with internal LPG cartridges, with a capacity of 225 g or less (see Annex D).
This document is applicable to the storage of all LPG cylinders.
NOTE 1        National regulations can apply to the technical requirements of LPG cylinders.
This document does not contain procedures for commissioning new LPG installations or system maintenance or upgrades.
This document does not apply to LPG-fuelled propulsion engines or LPG-driven generators.
NOTE 2        National codes and procedures appropriate to the country concerned can be available.

This document specifies performance levels and test methods for the following characteristics of slide fasteners made from interlocking components mounted on tapes: strengths of puller attachment, closed-end slide fastener bottom stop, top stop, open-end slide fastener box, reciprocating mechanism, closed slide fastener when extended laterally, open-end attachment when extended laterally, slider locking device, and open-end slide fastener single stringer slider retention and slider resistance to torque.
NOTE   The tests specified in Annexes B to K have been specifically devised to permit their direct application to finished slide fasteners with a view to giving the user reasonable assurance that a slide fastener conforming to the requirements of this document can satisfactorily fulfil its intended purpose. Annex L gives information about sampling procedures for bulk quantities of slide fasteners.
In addition, performance levels are also specified for colour fastness to washing, dry cleaning and water, and for dimensional stability to washing and dry cleaning.
This document is applicable to all different types of slide fasteners for general use and is not applicable to slide fasteners for specialist purposes (for example: pressure sealed slide fasteners for diving suits).

This document specifies minimum requirements and minimum performance criteria for conducting a single-laboratory validation study for qualitative (binary) real-time polymerase chain reaction (PCR) methods applied to the detection of specific DNA sequences present in foods.
The document is applicable to any single-laboratory validation of a qualitative real-time PCR method used for the detection of specific DNA sequences in food and food products (e.g. for the detection of genetically modified foodstuffs and for species determination, including species known to produce allergenic proteins).
The document does not apply to single laboratory validation of qualitative microbiological real-time PCR methods.
The document does not apply to the evaluation of applicability and practicability with respect to the specific scope of the PCR method.

This document specifies test methods and values for single-use paper bags manufactured from paper specified in EN 868-3, used as sterile barrier systems and/or packaging systems for terminally sterilized medical devices.
Other than the general requirements as specified in EN ISO 11607-1 and EN ISO 11607-2, this part of EN 868 specifies materials, test methods and values that are specific to the products covered by this document.

This document specifies a method for determining the resistance to mechanical penetration of nonwoven fabrics by a ball of a given diameter.
The method is primarily designed to be used on nonwovens with some degree of elasticity, for which a regular burst test does not apply.

IEC 63522-6:2025 is used for testing all kinds of relays and evaluates their ability to perform under expected conditions of transportation, storage, and all aspects of operational use.
This document defines a standard test method to measure contact-circuit resistance or voltage drop.

This document specifies the apparatus and the analytical methods for determining the content of in-can isothiazolinone preservatives in water-dilutable coating materials or related products.
This document is also applicable to polymer dispersions.

This document specifies the test suite structure (TSS) and test purposes (TPs) for evaluating the conformity of on-board equipment (OBE) and roadside equipment (RSE) to ISO 12813.
It provides a basis for conformance tests for dedicated short-range communication (DSRC) OBE and RSE to support interoperability between different equipment supplied by different manufacturers.
ISO 12813 specifies requirements for the compliance check communication (CCC) interface level, but not for the OBE or RSE internal functional behaviour. Consequently, tests regarding OBE and RSE functional behaviour remain outside the scope of this document.

This document specifies test methods and values for sealable adhesive coated paper manufactured from paper complying with EN 868-6, used as single-use sterile barrier systems and/or single-use packaging systems for terminally sterilized medical devices by the means of low temperature sterilization processes.
Other than the general requirements as specified in EN ISO 11607-1 and EN ISO 11607-2 [2], this part of EN 868 specifies materials, test methods and values that are specific to the products covered by this document.

The method describes the quantitative determination of the concentration of in-can free formaldehyde in water-dilutable coating materials.
Note: The standard can also be applied for polymer dispersions.
The determination method for in-can free formaldehyde can be only of limited suitability for pigmented systems, as the inherent coloration of the material may have an influence on the detection method.

ISO/IEC 15459-2:2015 specifies the procedural requirements to maintain identities and outlines the obligations of the Registration Authority and Issuing Agencies.
ISO/IEC 15459-2:2015 excludes those entities where ISO has designated Maintenance Agencies or Registration Authorities to provide identity and/or identifier schemes. It does not apply to:
freight containers, because their unique coding is specified in ISO 6346, Freight containers - Coding, identification and marking;
vehicles, because their unique identification is specified in ISO 3779, Road vehicles - Vehicle identification number (VIN) - Content and structure;
car radios, because their unique identification is specified in ISO 10486, Passenger cars - Car radio identification number (CRIN).  
The exclusion also applies to ISO 2108, Information and documentation - International standard book number (ISBN), and ISO 3297, Information and documentation - International standard serial number (ISSN).