SIST - Slovenian Institute for Standardization

IEC 63522-38:2025 This part of IEC 63522 is used for testing all kinds of electrical relays and for evaluating their ability to perform under expected conditions of transportation, storage and all aspects of operational use.
This document defines a standard test method for mechanical interlock.

IEC 62232:2025 provides methods for the determination of RF field strength, power density and specific absorption rate (SAR) in the vicinity of base stations (BS) for the purpose of evaluating human exposure.
This document:
a) considers intentionally radiating BS which transmit on one or more antennas using one or more frequencies in the range 110 MHz to 300 GHz;
b) considers the impact of ambient sources on RF exposure at least in the 100 kHz to 300 GHz frequency range;
c) specifies the methods to be used for RF exposure evaluation for compliance assessment applications, namely:
1) product compliance – determination of compliance boundary information for a BS product before it is placed on the market;
2) product installation compliance – determination of the total RF exposure levels in accessible areas from a BS product and other relevant sources before the product is put into operation;
3) in-situ RF exposure assessment – measurement of in-situ RF exposure levels in the vicinity of a BS installation after the product has been taken into operation;
d) specifies how to perform RF exposure assessment based on the actual maximum approach;
e) describes several RF field strength, power density, and SAR measurement and computation methodologies with guidance on their applicability to address both the in-situ evaluation of installed BS and laboratory-based evaluations;
f) describes how surveyors establish their specific evaluation procedures appropriate for their evaluation purpose;
g) provides guidance on how to report, interpret and compare results from different evaluation methodologies and, where the evaluation purpose requires it, determine a justified decision against a limit value;
h) provides methods for the RF exposure assessment of BS using time-varying beam-steering technologies such as new radio (NR) BS using massive multiple input multiple output (MIMO).
NOTE 1 Practical implementation case studies are provided as examples in the companion Technical Report IEC TR 62669 [5].
NOTE 2 Although the current BS product types have been specified to operate up to 200 GHz (see, for example, [6] and [7]), the upper frequency of 300 GHz is consistent with applicable exposure limits.
NOTE 3 The lower frequency considered for ambient sources, 100 kHz, is derived from ICNIRP-1998 [2] and ICNIRP-2020 [1]. However, some applicable exposure guidelines require ambient fields to be evaluated as low as 3 kHz, e.g. Safety Code 6 [4] and IEEE Std C95.1-2019 [3].
NOTE 4 Specification of appropriate RF exposure mitigation measures such as signage, access control, and training are beyond the scope of this document. It is possible to refer to the applicable regulations or recommended practices on these topics.
NOTE 5 While this document is based on the current international consensus about the best engineering practice for assessing the compliance of RF exposure with the applicable exposure limits, it is possible that national regulatory agencies specify different requirements. The entity conducting an RF exposure assessment needs to be aware of the applicable regulations.
This fourth edition cancels and replaces the third edition published in 2022. It includes corrections of obvious errors and text improvements on the third edition in order to bring more clarity in the description of the assessment methods and avoid misinterpretations. This edition has the same technical content as the third edition.

IEC 63522-37:2025 This part of lEC 63522 is used for testing all kinds of electrical relays and for evaluating their ability to perform under expected conditions of transportation, storage and all aspects of operational use. The object of this document is to define a standard test method to measure terminal temperature rise at rated load, included solder terminals, flat quick-connect terminations, screw and screwless type terminals, alternative termination types and sockets.

IEC 62840-1:2025 gives the general overview for battery swap systems, for the purposes of swapping batteries of electric road vehicles when the vehicle powertrain is turned off and when the battery swap system is connected to the supply network at standard supply voltages according to IEC 60038 with a rated voltage up to 1 000 V AC and up to 1 500 V DC.
This document is applicable for battery swap systems for EV equipped with one or more
– swappable battery systems (SBS), or
– handheld-swappable battery systems (HBS).
This document provides guidance for interoperability.
This document applies to
• battery swap systems supplied from on-site storage systems (for example buffer batteries etc),
• manual, mechanically assisted and automatic systems,
• battery swap systems intended to supply SBS/HBS having communication allowing to identify the battery system characteristics, and
• battery swap systems intended to be installed at an altitude of up to 2 000 m.
This document is not applicable to
• aspects related to maintenance and service of the battery swap station (BSS),
• trolley buses, rail vehicles and vehicles designed primarily for use off-road,
• maintenance and service of EVs,
• safety requirements for mechanical equipment covered by the ISO 10218 series,
• locking compartments systems providing AC socket-outlets for the use of manufacturer specific voltage converter units and manufacturer specific battery systems,
• electrical devices and components, which are covered by their specific product standards,
• any fix-installed equipment of EV, which is covered by ISO, and
• EMC requirements for on-board equipment of EV while connected to the BSS.
This first edition cancels and replaces the first edition of IEC TS 61280-1 published in 2016.
This edition includes the following significant technical changes with respect to IEC TS 61280-1:2016:
a) expanded scope to include handheld-swappable battery systems (HBS) and guidance on interoperability;
b) added definitions for "handheld-swappable battery system" (HBS) and expanded related terms such as "SBS/HBS coupler," "SBS/HBS charger," etc;
c) added classifications based on supply network characteristics, connection method, access and type of BSS;
d) added support for HBS, detailing the different compositions and workflows for type A (SBS) and type B (HBS) battery swap stations;
e) added requirements for functional interoperability, interface interoperability, data interoperability, operational interoperability, compatibility with legacy systems, and scalability;
f) added requirements for communication, protection against electric shock, specific requirements for accessories), cable assembly requirements, BSS constructional requirements, overload and short circuit protection, EMC, emergency switching or disconnect, marking and instructions;
g) expanded annex content, adding solutions for manual swapping stations for motorcycles with HBS and updating use cases.

IEC 63522-16:2025 This part of IEC 63522 is used for testing along with the appropriate severities and conditions for measurements and tests designed to assess the ability of DUTs to perform under expected conditions of transportation, storage and all aspects of operational use.
This document defines a standard test method for resistance to soldering heat and solderability for standard soldering processes.

IEC 63522-56:2025 This part of IEC 63522 is used for testing along with the appropriate severities and conditions for measurements and tests designed to assess the ability of specimens to perform under expected conditions of transportation, storage and all aspects of operational use.
The object of this test is to define a standard test method for evaluation of appropriate materials to withstand mechanical pressure at elevated temperatures without undue deformation.

RTS/LI-00280

IEC 60060-2:2025 is applicable to complete measuring systems and to their components, used for the measurement of high voltages during laboratory and factory tests with direct voltage, alternating voltage and lightning and switching impulse voltages and combined and composite voltages as specified in IEC 60060-1. For measurements during on-site tests, see IEC 60060-3. The limits on uncertainties of measurements stated in this document apply to test levels stated in IEC 60071-1. The principles of this document apply also to higher levels but the uncertainty can be greater.
This document:
• defines the terms used;
• describes methods to estimate the uncertainties of high-voltage measurements;
• states the requirements that apply to measuring systems;
• describes the methods for approving a measuring system and checking its components;
• describes the procedures by which the user demonstrates that a measuring system meets the requirements of this document, including the limits set for the uncertainty of measurement.
This fourth edition cancels and replaces the third edition published in 2010. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) The general layout and text has been updated and improved to make the standard easier to use.
b) This document has been revised to align it with the fourth edition of IEC 60060-1.
c) The treatment of measurement uncertainty estimation has been expanded.
d) This document is now applicable to measuring systems used in testing at all standard insulation levels specified in IEC 60071-1.
e) The measurement uncertainty requirement for the front time of the standard lighting impulse voltage has been changed from 10 % to 15 %, for testing at all standard insulation levels specified in IEC 60071-1.
f) The parameter "time-to-peak" of the switching impulse defined in the third edition of IEC 60060-1:2010 has been replaced by "front time" in the fourth edition of IEC 60060-1. Necessary changes have been made in this document to accommodate this change in IEC 60060-1.
g) Clause 10, Measurement of combined voltages and Clause 11, Measurement of composite voltages have been added.
h) Clause B.1 has been significantly revised to align more closely with the provisions of Clause 5, including using the same nomenclature.

IEC 63522-44:2025 This part of IEC 63522 is used for testing all kinds of electrical relays and for evaluating their ability to perform under expected conditions of transportation, storage and all aspects of operational use. The object of this test is to define a standard test method for salt mist.

This document specifies the requirements for permanent paper intended for documents. It is applicable to unprinted papers. It is not applicable to boards.
NOTE 1        The terms paper and board are defined in ISO 4046-3.
This document is not intended for judging the permanence of papers stored under hostile conditions, such as high humidity that can promote microbiological attack, excessive heat, radiation (light or other), high levels of atmospheric pollutants, or the influence of water.
NOTE 2        For information on International Standards on paper permanence (ISO 9706), on archival paper permanence and durability (ISO 11108), and on paper stability for general graphic applications (ISO 20494), refer to Annex D.

IEC 60730-2-14: 2025 applies to automatic electric actuators
• for use in, on, or in association with equipment for household appliance and similar use;
NOTE 1 Throughout this document, the word "equipment" means "appliance and equipment" and "control" means "electric actuator".
EXAMPLE 1 Electric actuators for appliances within the scope of IEC 60335.
• for building automation within the scope of ISO 16484 series and IEC 63044 series (HBES/BACS);
EXAMPLE 2 Independently mounted electric actuators for use in smart grid systems and for building automation systems within the scope of ISO 16484-2.
for equipment that is used by the public, such as equipment intended to be used in shops, offices, hospitals, farms and commercial and industrial applications;
EXAMPLE 3 Electric actuators for commercial catering, heating, and air-conditioning equipment.
• that are smart enabled;
• that are AC or DC powered electric actuators with a rated voltage not exceeding 690 V AC or 600 V DC;
• used in, on, or in association with equipment that use electricity, gas, oil, solid fuel, solar thermal energy, etc., or a combination thereof;
• utilized as part of a control system or controls which are mechanically integral with multifunctional controls having non-electrical outputs;
• using NTC or PTC thermistors and to discrete thermistors, requirements for which are contained in Annex J;
• that are mechanically or electrically operated, responsive to or controlling such characteristics as temperature, pressure, passage of time, humidity, light, electrostatic effects, flow, or liquid level, current, voltage, acceleration, or combinations thereof; as well as manual controls when such are electrically and/or mechanically integral with automatic controls.
NOTE 2 Requirements for manually actuated mechanical switches not forming part of an automatic control are contained in IEC 61058-1-1.
This document applies to
– the inherent safety of automatic electric actuators, and
– functional safety of automatic electric actuators and safety related systems,
– controls where the performance (for example the effect of EMC phenomena) of the product can impair the overall safety and performance of the controlled system,
– the operating values, operating times, and operating sequences where such are associated with equipment safety.
This document specifies the requirements for construction, operation and testing of automatic electric actuators used in, on, or in association with an equipment.
This document does not
• apply to automatic electric actuators intended exclusively for industrial process applications unless explicitly mentioned in the relevant part 2 or the equipment standard. However, this document can be applied to evaluate automatic electric actuators intended specifically for industrial applications in cases where no relevant safety standard exists;
• take into account the response value of an automatic action of an electric actuator, if such a response value is dependent upon the method of mounting the electric actuator in the equipment. Where a response value is of significant purpose for the protection of the user, or surroundings, the value defined in the appropriate equipment standard or as determined by the manufacturer will apply;
• address the integrity of the output signal to the network devices, such as interoperability with other devices unless it has been evaluated as part of the control syst

RTS/LI-00276-1

This document specifies a method to determine the resistance of geosynthetics to dynamic penetration by a steel cone dropped from a fixed height.
The method is generally applicable to geosynthetics. However, the applicability of this test for some types of products (such as e.g. GGR,GCE, GST,GBR) should be considered carefully .

This document specifies the characteristics of valves made from unplasticized polyamide (PA-U) in accordance with ISO 16486-1, intended to be buried and used for the supply of gaseous fuels.
NOTE 1        For the purpose of this document the term gaseous fuels include for example natural gas, methane, butane, propane, hydrogen, manufactured gas, biogas, and mixtures of these gases. Additional information about the suitability for 100 % hydrogen and its admixtures with natural gas is given by ISO 16486-1:2023, Annex C and Annex D.
It is applicable to isolating unidirectional and bi-directional valves with spigot ends or electrofusion sockets intended to be fused with PA-U pipes conforming to ISO 16486-2 and PA-U fittings conforming to ISO 16486-3.
This document also specifies the test parameters for the test methods it describes.
In conjunction with ISO 16486-1, ISO 16486-2, ISO 16486-3 and ISO 16486-5, this document is applicable to PA-U valves and their joints and to joints with components of PA-U and other materials intended to be used under the following conditions:
a)       a maximum operating pressure (MOP) of up to and including 18 bar1), or limited to 16 bar under regional CEN requirements, at a reference temperature of 20 °C for design purposes;
NOTE 2        For the purpose of this document and the references to ISO 8233, MOP is considered to be nominal pressure.
b)       an operating temperature of −20 °C to 40 °C;
NOTE 3        For operating temperatures between 20 °C and 40 °C, derating coefficients are specified in ISO 16486-5.
This document covers valves for pipes with a nominal outside diameter, dn, ≤400 mm.

IEC 63522-20:2025 This part of IEC 63522 is used for testing along with the appropriate severities and conditions for measurements and tests designed to assess the ability of DUTs to perform under expected conditions of transportation, storage and all aspects of operational use.
This document defines a standard test method for mechanical endurance.

This document specifies a method to determine the susceptibility of textile floor coverings to mechanical damage at cut edges.
It is applicable to textile floor coverings both as broadloom materials and as tiles and planks.

IEC 63522-49:2025 This part of IEC 63522 is used for testing all kinds of electrical relays and for evaluating their ability to perform under expected conditions of transportation, storage and all aspects of operational use. This document defines a standard test method for long term stability of sealing.

IEC 63522-24:2025 This part of IEC 63522 is used for testing along with the appropriate severities and conditions for measurements and tests designed to assess the ability of DUTs to perform under expected conditions of transportation, storage and all aspects of operational use.
This document defines a test to check that a multipole relay is capable of transferring one source to another.

RTS/LI-00276-3

RTS/LI-00277

IEC 63522-27:2025 This part of IEC 63522 is used for testing all kinds of electrical relays and for evaluating their ability to perform under expected conditions of transportation, storage and all aspects of operational use. This document defines a standard test method for electrical contact noise.

This document specifies test methods for determining the radiant power and radiant energy of continuous wave and pulsed laser beams, as well as their temporal characteristics of pulse shape, pulse duration and pulse repetition rate. Test and evaluation methods are also given for the radiant power stability of cw-lasers, radiant energy stability of pulsed lasers and pulse duration stability.
The test methods given in this document are used for the testing and characterization of lasers.

IEC 63522-22:2025 This part of IEC 63522 is used for testing along with the appropriate severities and conditions for measurements and tests designed to assess the ability of DUTs to perform under expected conditions of transportation, storage and all aspects of operational use.
This document defines a standard test method for evaluation of the limiting continuous current under specified conditions.

This part of IEC 60684 gives the requirements for two types of heat-shrinkable, polyolefin sleeving, stress control, not flame retarded, with a nominal shrink ratio up to 3:1.
This sleeving has been found suitable for use up to temperatures of 100 °C.
- Type A : Medium wall Internal diameter up to 65,0 mm typically
- Type B : Thick wall Internal diameter up to 95,0 mm typically
This sleeving is normally supplied in the colour black.
Since these types of sleevings cover a significantly large range of sizes and wall thicknesses, Annex A in this standard provides guidance to the range of sizes available. The actual size will be agreed between the user and the supplier.
Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application need to be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone.
This sleeving is designed to be used in MV cable accessories and as such electrical performance will be proven as part of the assembly. Examples of this are described in HD 629 and IEC 60502 (all parts)

IEC 63522-9:2025 This document used for testing all kinds of relays and evaluates their ability to perform under expected conditions of transportation, storage and all aspects of operational use. It defines standard test methods to determine the ability of the relay to withstand certain climatic test conditions, a sequence of such climatic test conditions or climatic storage conditions.

IEC 63522-28:2025 This part of IEC 63522 is used for testing all kinds of electrical relays and for evaluating their ability to perform under expected conditions of transportation, storage and all aspects of operational use. This document defines a standard test method for thermoelectric electromotive force (e.m.f.).

IEC 63522-40:2025 This document is used for testing along with the appropriate severities and conditions for measurements and tests designed to assess the ability of DUTs to perform under expected conditions of transportation, storage and all aspects of operational use. This document defines a standard test method for short circuit testing.

This document specifies the requirements and recommendations for the transportation of CO2 streams from the capture site to the storage facility where it is primarily stored in a geological formation or used for other purposes (e.g. for enhanced oil recovery or CO2 use).
This document applies to the transportation of CO2 streams by
—     rigid metallic pipelines,
—     pipeline systems,
—     onshore and offshore pipelines for the transportation of CO2 streams,
—     conversion of existing pipelines for the transportation of CO2 streams, and
—     transportation of CO2 streams in the gaseous and dense phases.
This document also includes aspects of CO2 stream quality assurance, as well as converging CO2 streams from different sources.
Health, safety and environment aspects specific to CO2 transport and monitoring are also considered in this document.
Transportation of CO2 via ship, rail or on road is not covered in this document.

REN/ESI-0019412-4v141

REN/ESI-0019412-1v161

The requirements of this document set out the materials, construction, and performance of components intended for use in fixed foam fire fighting systems, and using foam concentrates conforming to EN 1568-1 to EN 1568-4. The components covered are: proportioners, sprayers, semi-subsurface hose units, branchpipes, low/medium expansion foam generators, high expansion foam generators, foam chambers, tanks and pressure vessels. Methods of test are given in Annex A to Annex K.
Requirements are also given for the provision of the characteristic data needed for correct application of components.
NOTE 1   Unless otherwise stated pressures are gauge pressures expressed in bar.
The requirements of this document do not cover, except where stated, the use of combinations of components to form part, or the whole, of a fire fighting system.
NOTE 2   Components conforming to this document are not necessarily compatible one with another.
Requirements for pumps, motors and the functioning of mechanical components (i.e. remote control turrets) are outside the scope of this document.

REN/ESI-0019412-5v251

This document specifies methods to determine the durability of bondings, prepared by means of adhesive materials (e.g. adhesive tapes and adhesive masses), for the establishment of airtight layers under climatic conditions representative for indoor environments based on test methods with and without ageing.
The methods provided in this document require at least 120 days for aging and are therefore not suitable for a short time evaluation nor can they be applied to in-field testing. This document excludes test methods for external weathering or UV exposure, even though this might occur during the construction phase.
The following typical applications are distinguished:
-   bonding of the overlap of flexible airtightness layers;
-   bonding of flexible airtightness layers to construction products and penetrations;
-   establishment of airtightness layers by means of sheet materials and adhesive tapes.
This document does not apply to test methods for:
-   pre-compressed sealing tapes and sealing profiles which will be mechanically secured;
-   butyl-based adhesive tapes or adhesive masses;
-   sheet joints of wood-based panels or gypsum plasterboards with adhesive masses or filler systems;
-   bondings of bitumen membranes or of bitumen membranes to construction products;
-   bonding of self-adhesive membranes;
-   adhesive masses from reels. Adhesive masses from reels are cured viscoelastic adhesive masses, which are used in the same field of application as adhesive masses.
The tack is not addressed. It does not allow any conclusion on the durability of a bonding.

REN/ESI-0019412-2v241

This document provides a measurement method to assess the reliability of washing machines for household use. This document defines the functional analysis, limiting events/states, environmental conditions and test conditions of washing machines. It also elaborates on the level of confidence on the measurement results.
NOTE 1   The method is based on EN 45552 (General method for the assessment of the durability of energy-related products) and takes into account EN 45554 (General methods for the assessment of the ability to repair, reuse and upgrade energy-related products).
This document provides information about the interrelations of reliability, repairability and upgradeability with consideration towards a durability assessment for washing machines for household use.
This document provides input/results about the investigation on the assessment of repairability and upgradeability for washing machines for household use.
This document is not intended to be used to assess the reliability of:
-   washing machines, intended for commercial or industrial use;
-   washer-dryers.
NOTE 2   A testing method for washing machines unable to provide heated washing programmes have a low market relevance and will be considered in a future edition of this standard.
This document does not address the ability of washing machines to be reused.
Product functions related to the safety of washing machines are out of the scope of this document.
NOTE 3   EN 60335-2-7 addresses safety requirements for household appliances. It includes aging tests that are relevant to safety.
This document is intended to be used for the validation of a reliability declaration.

This document specifies a method for the determination of the adhesivity of cut-back or fluxed bituminous binders coated onto aggregate when immersed in water.
The method can be used with a reference aggregate. In that case, it measures the intrinsic adhesion behaviour of a cut-back and fluxed bituminous binder. The method can also be used with a specific aggregate as used on a job site.
WARNING — The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use. For environmental reasons and to reduce emissions to air, water and soil, it is recommended to limit the use of products, solvents and energy to the minimum required for a valid test result.

This document specifies requirements and test methods for determining the concentration of phenol in aqueous toy materials and for migration of phenol from polymeric toy materials. This document is applicable to toys intended for use by children under 36 months or other toys intended to be placed in the mouth.
NOTE   The European Commission Guidance Document No 11 on the Application of Directive 2009/48/EC on the Safety of Toys [4] provides guidelines to help on the classification of toys intended for children under 36 months of age or of 36 months and over.

This document applies to unplasticized poly(vinyl chloride) (PVC-U) profiles that are intended to be used for the fabrication of windows and doors in accordance with the EN 14351 series or EN 16034, shutters according to EN 13659 and other construction profiles in accordance with the EN 13245 series. Furthermore, this document is also applicable for profiles used in other PVC-U products, which can include recyclates. This document gives references and specifies general and product-specific design for recycling principles.
NOTE 1   In this document, the term “PVC-U profiles” is used to refer to construction profiles made from PVC-U, PVC-UE, and PVC-U-based natural fibre composites (NFC).
NOTE 2   For editorial reasons in this document the term window is used for window/door.
Criteria for the use of materials, process conditions, and recyclability are defined, which are considered during the design process.
This document defines principles to
-   obtain the highest possible share of recyclability of the PVC-U part in the profile, and
-   increase the share of PVC-U recyclate in the profile,
while complying with requirements for the final product, where existent and defined elsewhere. This document establishes flowcharts which help to assess, (i) how recyclability is evaluated and (ii) whether inclusion of rPVC-U is possible.
The following components of the final PVC-U construction product are considered in this document:
-   profiles;
-   reinforcements;
-   gaskets;
-   insulations;
-   coverings.
This document specifies only the technical connection of the profile to other components (such as glazing or hardware) and their impact on the recyclability of the PVC-U profiles. The recyclability of the other components (e.g. glazing, aluminium cover, hardware) is excluded from this document.
NOTE 3   Examples for profiles included in this document and their intended use can be found in Figure 1.
Figure 1 - Examples for profiles included in this document and their intended use (frame and sash profile with reinforcements, window, door, cladding and shutter box with shutter)

This document specifies requirements (content limit) and a test method for certain flame retardants in toy materials.

IEC 63522-32:2025 This document is used for testing under appropriate severities and conditions for measurements and tests designed to assess the ability of DUTs to perform under expected conditions of transportation, storage and all aspects of operational use. This document defines a standard test method to investigate the effect of acoustic noise in conjunction with the operating, releasing and cycling noise of a relay and the immunity of a relay to acoustic noise.

This document specifies requirements for formamide in foam toy materials and a test method for determining the content of formamide in foam toy materials. This document is applicable to toys intended for use by children under 36 month or other toys intended to be placed in the mouth.
NOTE 1 The document provides a test method to determine if the total content of formamide in foam toy materials is below the 200 mg/kg cut-off limit. Foam toy materials exceeding this limit are subject to the emission limit specified in Appendix C to Annex II to Directive 2009/48/EC.
NOTE 2 The European Commission Guidance Document No 11 on the Application of Directive 2009/48/EC on the Safety of Toys [3] provides guidelines to help on the classification of toys intended for children under 36 months of age or of 36 months and over.

This document specifies the main characteristics and associated test methods for assessing of polystyrene (PS) recyclates intended for use in the production of semi-finished/finished products.
It is intended to support parties involved in the use of PS recyclates to agree on specifications for specific and generic applications.
This document does not cover the characterization of plastics wastes, which is covered by the EN 15347 series, neither traceability topics which are covered by EN 15343.

This document specifies the dimensions, linear resistance, mechanical characteristics, construction and mass of conductors in aluminium or aluminium alloy for electrical cables for aerospace applications.
It applies to stranded conductors with nominal cross-sections of 5 mm2 to 115 mm2 inclusive.

This document specifies the characteristics of three-pole circuit breakers, temperature compensated with a rated current from 1 A to 25 A, used in aircraft on-board circuits at a temperature between
-55 °C and 125 °C for ratings ≤ 15 A and -55 °C to 90 °C for ratings > 15 A and at an altitude of 22 000 m max.
These circuit breakers are operated by a push-pull type single pushbutton (actuator), with delayed action "trip-free" tripping with a signal contact which is open when main contacts are closed, and inversely.
They will continue to function up to the short-circuit current.

This document specifies requirements and a test method for migration of bisphenol A from toy materials. This document is applicable to toys intended for use by children under 36 months or other toys intended to be placed in the mouth.
NOTE   The European Commission Guidance Document No 11 on the Application of Directive 2009/48/EC on the Safety of Toys [3] provides guidelines to help on the classification of toys intended for children under 36 months of age or of 36 months and over.

1.1   This document specifies a direct measurement method for characterizing the surface roughness of the rail and wheel associated with rolling noise ("acoustic roughness"), in the form of a one-third octave band spectrum.
This document describes a method for:
a)   selecting measuring positions along a track or selecting wheels of a vehicle;
b)   selecting lateral positions for measurements;
c)   the data acquisition procedure;
d)   measurement data processing in order to estimate a set of one-third octave band roughness spectra;
e)   presentation of this estimate for comparison with limits of acoustic roughness;
f)   comparison with a given upper limit in terms of a one-third octave band wavelength spectrum;
g)   the measuring system requirements.
1.2   It is applicable to the:
a)   compliance testing of reference track sections in relation to the acceptance test for noise emitted by railway vehicles;
b)   performance testing of track sections in relation to noise emitted by railway vehicles;
c)   acceptance of the running surface condition only in the case where the acoustic roughness is the acceptance criterion;
d)   assessment of the wheel surface condition as an input for the acoustic acceptance of brake blocks;
e)   assessment of the wheel and rail roughness as input to the calculation of combined wheel rail roughness;
f)   diagnosis of wheel-rail noise issues for specific tracks or wheels;
g)   assessment of the wheel and rail roughness as input to rolling noise modelling;
h)   assessment of the wheel and rail roughness as input to noise source separation methods.
1.3   It is not applicable to the:
a)   measurement of roughness (rail roughness, wheel roughness or combined roughness) using an indirect method;
b)   analysis of the effect of wheel-rail interaction, such as a “contact filter”;
c)   approval of rail and wheel reprofiling, including rail grinding operations, except for those where the acoustic roughness is specifically the approval criterion (and not the grinding quality criteria as provided in e.g. EN 13231-3);
d)   characterization of track and wheel geometry except where associated with noise generation.

This document specifies the characteristics of three-pole circuit breakers, temperature compensated with a rated current from 1 A to 25 A, used in aircraft on-board circuits at a temperature between −55 °C and 125 °C for ratings ≤ 15 A and −55 °C and 90 °C for ratings > 15 A and at an altitude of 22 000 m max.
These circuit breakers are operated by a push-pull type single push button (actuator), with delayed action “trip-free” tripping with a polarized signal contact which is open when main contacts are closed, and inversely.
They will continue to function up to the short-circuit current.

This document specifies fundamental requirements for uncut finished spectacle lenses. This document is not applicable to protective spectacle lenses.
This document takes precedence over the corresponding requirements of other standards, if differences exist.

This document specifies the main characteristics and associated test methods for assessing of acrylonitrile-butadiene-styrene (ABS) recyclates intended for use in the production of semi-finished/finished products.
It is intended to support parties involved in the use of ABS recyclates (rABS) to agree on specifications for specific and generic applications.
This document does not cover the characterization of plastic wastes, which is covered by the EN 15347 series, neither traceability topics which are covered by EN 15343.