CEN - European Committee for Standardization

This document specifies the quality grades for sorted poly(vinyl chloride) (PVC) wastes as well as specific test methods laying out those properties for which the supplying party of the waste makes information available to the receiving party. PVC waste quality grades are based on pre-determined sets of characteristics, taking into account sectorial and market specificities and related information needs and tests methods. The document provides for a division of information between “Required Data”, where a statement is required, and additional “Optional Data” as agreed between the supplying and receiving party.
This document does not apply to the general characterization addressed in EN 15347-1.

This document is applicable to oil stoves. These appliances have one or more vaporizing burners and a nominal heating capacity of not more than 15 kW and are equipped either with a draught regulator or a combustion air limiter.
The intended use of the appliances is space heating in residential buildings.
This document is also applicable to appliances with fan assisted vaporizing burners.
According to the type of fuels used in the country of destination, the appliances are supplied for use with either:
-   fuel oil with a maximum kinematic viscosity of 6,0 mm²/s at 20 °C;
-   or kerosene with a flash point of not less than 40 °C.
This document is not applicable for:
-   built-in appliances;
-   appliances equipped with an atomizing burner;
-   appliances incorporating a boiler or connected to a water system.
This document specifies procedures for assessment and verification of constancy of performance (AVCP) of characteristics of flued oil stoves with vaporizing burners.

This document specifies the general safety requirements for demountable machines and trailers, including road-rail trailers - henceforward referred to as ‘machines, for use when travelling and working on railway track.
NOTE   Trailers, including road-rail trailers, are considered as machines because they are moved along the track by powered machines.
This document specifies the requirements to deal with the common hazards presented by their use on the railway during transport, assembly and installation, commissioning, travelling and working on track, use including setting, programming, and process changeover, operation, cleaning, fault finding, maintenance and de-commissioning of the machines and associated equipment when they are used as intended and under conditions of misuse which are reasonably foreseeable.
These machines will not run on railway lines open to normal traffic.
NOTE   Other rail mounted railway maintenance and infrastructure inspection machines are dealt with in other European standards, see Technical Report CEN/TR 17498:2020.
This document is also applicable to machines and associated equipment that in working mode are partly supported on the ballast or the formation.
The requirements in this document are based on the assumption that the machines are used, operated and maintained by skilled person(s).
This document does not apply to the following:
-   requirements for quality of the work or performance of the machine;
-   use of separate equipment temporarily mounted on machines;
-   machines that utilize external power supplies such as the overhead contact line system for traction purposes or as a power source;
-   hazards due to air pressure caused by the passing of high-speed trains at more than 200 km/h;
-   operation subject to special rules, e.g. potentially explosive atmospheres;
-   hazards due to natural causes, e.g. earthquake, lightning, flooding;
-   working methods;
-   operation in severe working conditions requiring special measures, e.g. corrosive environments, contaminating environments, strong magnetic fields;
-   hazards occurring when used to handle suspended loads which may swing freely.

This document is applicable to residential liquid fuel burning appliances intended for space heating.
This document specifies requirements relating to the design, manufacture, construction, safety and performance (efficiency and emission) of appliances fired by liquid fuel (hereafter referred to as “appliance(s)”) and provides instructions for them. Furthermore, it also gives provisions for the evaluation of conformity, i.e. initial type testing (ITT) and factory production control (FPC) and marking of these appliances.
This document specifies the test methods for the determination of the smoke number, and CO, NOx, and OGC emission test methods.
This document does not apply to:
-   built-in appliances;
-   appliances equipped with an atomizing burner;
-   appliances incorporating a boiler or connected to a water system.

This document specifies test methods and acceptance criteria, within the frequency range of 0,5 MHz to 15 MHz, for assessing the performance of equipment dedicated for determining thickness using pulse-echo ultrasound, e.g. according to ISO 16809.
This document only specifies the verifications required for the determination of thickness.
This document is applicable to instruments with numerical display and instruments with A-scan presentation, each using either single- or dual-transducer probes.
The tests described in this document can be used for verifying equipment covered by ISO 22232-1 and ISO 22232-2 when used for thickness determination.

This document is applicable to space heaters, inset appliances and cookers intended for mechanical fuelling with wood pellets and for manual fuelling with wood logs. They can be freestanding or inset appliances.
The intended use of the appliances is space heating in residential buildings and can be cooking. They can be fitted with a boiler (integral part of the appliance containing water to be heated up) for the supply of hot water for central heating systems.
These appliances typically use auxiliary energy which is measured in this standard as well. They are operated with natural draught and can be fan-assisted.
NOTE 1   A fan-assisted appliance does still operate under negative pressure in the flue gas system.
For inset appliances and especially their testing additional information can be necessary from EN 16510-2-2:2022.
These appliances burn wood pellets and wood logs only, in accordance with the appliance instructions. They only operate with the firedoors closed.
NOTE 2   These appliances can have an integral fuel hopper or be combined with an external fuel hopper.
These appliances can be fitted with a single or double combustion chamber having a single flue gas outlet.
This document specifies procedures for assessment and verification of constancy of performance (AVCP) of characteristics of combination appliances fired by wood logs and pellets.
This document is not applicable to appliances:
-   with boiler intended for water systems having water temperatures above 110°C and 3 bar and for sanitary hot water,
-   intended to be used with a pure horizontal exhaust (through the building wall),
-   with flue gas condensation in the appliance,
-   switching on / off for part load operation,
-   with simultaneous wood and pellet operation with a single flue gas outlet,
-   with non-automatic pellet loading,
-   with single combustion chamber and double flue gas outlet,
-   continuous burning appliances.
For clarity, all test methods are addressed in Annex A.

This document specifies a method for the determination of reaction temperatures and times, enthalpies of reaction, and degrees of conversion using conventional differential scanning calorimetry (DSC) as specified in ISO 11357-1.
The method applies to monomers, prepolymers, and polymers in the solid or liquid state. The material can contain fillers and/or initiators in the solid or liquid state.
This document is not applicable to fast DSC as specified in ISO 23976.[1]

1.1   Scope of EN 1993-1-6
(1) EN 1993-1-6 provides rules for the structural design of plated steel structures that have the form of a shell of revolution (axisymmetric shell).
(2) This document is applicable to unstiffened fabricated axisymmetric shells formed from isotropic rolled plates using both algebraic and computational procedures, and to stiffened axisymmetric shells with different wall constructions using computational procedures. It also applies to associated circular or annular plates and to beam section rings and stringer stiffeners where they form part of the complete shell structure. The general computational procedures are applicable to all shell forms.
(3) This document does not apply to manufactured shells or to shell panels or to elliptical shell forms, except that its computational procedures are applicable to all shell structures. This document does not apply to structures under seismic or other dynamic loading. It does not cover the aspects of leakage of stored liquids or solids.
(4) Cylindrical and conical panels are not explicitly covered by this document. However, the provisions of 9.8 can be used provided that appropriate boundary conditions are taken into account.  
(5) This document defines the characteristic and design values of the resistance of the structure.
(6) This document is concerned with the requirements for design against the ultimate limit states of:
—   plastic failure;
—   cyclic plasticity;
—   buckling;
—   fatigue.
(7) Overall equilibrium of the structure (sliding, uplifting, overturning) is not included in this document. Special considerations for specific applications are included in the relevant application parts of EN 1993.
(8) Detailed formulae for the simple calculation of unstiffened cylinders, cones and spherical domes are given in the Annexes.
(9) Provisions for simple calculations on specific stiffened shell types are given in EN 1993-4-1.
(10) This document is intended for application to steel shell structures. Where no standard exists for shell structures made of other metals, including high strength steels, the provisions of this document are applicable provided the appropriate material properties of the metal are taken into account.
(11) The provisions of this document are intended to be applied within the temperature ranges defined in the relevant EN 1993 application parts.
(12) Where no application part defines a different range, this document applies to structures within the following limits:
—   design metal temperatures lie within the range −50 °C to +100 °C, except when using the special provisions given in 5.1;
—   radius to thickness ratios (r/t) within the range 50 to 2 000;
—   manufactured circular hollow sections according to EN 10210 and EN 10219 are outside the scope of this document and are covered by EN 1993-1-1. However, if no other provisions are available, the rules of this document are useful for manufactured circular hollow sections. In particular, this document is applicable to the design of manufactured piles (see EN 1993-5) provided the imperfections and tolerance requirements of EN 1993-5 are adopted in place of those specified in this document, and where no other standard covers the specific pile geometry.
NOTE 1   Experimental and theoretical data relating to manufactured circular hollow sections were not considered when this document was drafted. The application of this document to such structures therefore remains the responsibility of the user.  
NOTE 2   The stress design rules of this document can be rather conservative if applied to some geometries and loading conditions for relatively thick-walled shells.
NOTE 3   Thinner shells than r/t = 2 000 can be treated using these provisions but the provisions have not been verified for such thin shells.
NOTE 4   The maximum temperature is restricted so that the influence of creep can be ignored where high temperature creep effects are not covered by the relevant application part.
[...]

The existing Annex ZB is still incorrectly referring to the old 97/23/EC Directive. Reference should be made to Directive 2014/68/EU for pressure equipment. To be done via this WI.

This document specifies the quality grades for sorted polystyrene (PS) wastes as well as specific test methods laying out those properties for which the supplying party of the waste makes information available to the receiving party. PS waste quality grades are based on pre-determined sets of characteristics, taking into account sectorial and market specificities and related information needs and tests methods. The document provides for a division of information between “Required Data”, where a statement is required, and additional “Optional Data” as agreed between the supplying and receiving party.
This document does not apply to the general characterization addressed in EN 15347-1.

This document specifies the quality grades for sorted Polyethylene (PE) wastes as well as specific test methods laying out those properties for which the supplying party of the waste makes information available to the receiving party. Polyethylene waste quality grades are based on pre-determined sets of characteristics, taking into account sectorial and market specificities and related information needs and tests methods. The document provides for a division of information between “Required Data”, where a statement is required, and additional “Optional Data” as agreed between the supplying and receiving party.
This document does not apply to the general characterization addressed in EN 15347-1.

This European Standard covers multi-firing sauna stoves in which the heating stones are separated from and indirectly heated by the fire and the flue gases and which may be re-fuelled with several fuel loads.
This European Standard specifies requirements relating to the design, manufacture, construction, safety and performance (efficiency and emission) of multi-firing sauna stoves fired by wood logs and provides instructions for them. Furthermore, it also gives provisions for evaluation of conformity (i.e. initial type testing (ITT) and factory production control (FPC) and marking of these products.
This standard is applicable to hand-fuelled intermittent burning multi-firing sauna stoves, which provide heat into the space where they are installed.
These multi-firing sauna stoves may be supplied either as an assembled appliance or as a manufacturer’s pre-designed unit consisting of pre-fabricated components designed to be built on site in accordance with the manufacturer’s specified assembly instructions. One-off installations are not included.
These multi-firing sauna stoves may burn only natural wood logs in accordance with the appliance operating instructions.
Single-firing heat storage sauna stoves, in which the stones are directly heated by the fire and the flue gases, which pass through them, are not covered by this European Standard. This standard is also not applicable to mechanically fed sauna stoves, sauna stoves having fan assisted combustion air, sauna stoves fitted with a boiler, sauna stoves with incorporated flue or sauna stoves having any electrical connection.

This document specifies the quality grades for sorted poly(ethylene terephtalate) (PET) wastes as well as specific test methods laying out those properties for which the supplying party of the waste makes information available to the receiving party. PET waste quality grades are based on pre-determined sets of characteristics, taking into account sectorial and market specificities and related information needs and tests methods. The document provides for a division of information between “Required Data”, where a statement is required, and additional “Optional Data” as agreed between the supplying and receiving party.
This document does not apply to the general characterization addressed in EN 15347-1.

This document specifies the quality grades for sorted polypropylene (PP) wastes as well as specific test methods laying out those properties for which the supplying party of the waste makes information available to the receiving party. Polypropylene waste quality grades are based on pre-determined sets of characteristics, taking into account sectorial and market specificities and related information needs and tests methods. The document provides for a division of information between “Required Data”, where a statement is required, and additional “Optional Data” as agreed between the supplying and receiving party.
This document does not apply to the general characterization addressed in EN 15347-1.

This document specifies procedures for assessing the resistance of paint systems when a cut in the form of a right-angle lattice pattern (cross-cut) or in the form of an X (X-cut) is made into the paint, penetrating through to the substrate. This document is only applicable if the cross-cut or X-cut test method is specified, together with the rating from the appropriate rating scale.
This document also specifies suitable equipment and defines inspection areas, sampling plans and acceptance/rejection criteria.
It does not specify ratings for particular coating systems.

This document defines the common terms, abbreviations and references used throughout the EN 9300 series of standard parts.

The purpose of this document is to provide customers and their suppliers with a document specifying the notions of “construction” and “management” of product dependability and safety (RAMS).
It offers programme directors and project managers information likely to help them:
—   determine the tasks to be performed and the application procedures, according to the specific nature of the programme and its goals;
—   define and implement the provisions necessary for performing these tasks;
—   within programme execution, situate the various tasks involved in constructing and managing the RAMS of a product.
This document applies to all programmes that involve customer/supplier relation.
RAMS management concerns not only all the products covered by these programmes, but also the components of these products and the production and support resources and processes to be implemented.
The provisions of this document can be negotiated at all levels between the parties directly concerned by a given programme. This implies, on the part of the ordering parties, that each lower level is provided with the information needed to perform the tasks and meet the specified targets. This also implies, on the part of suppliers, an escalation of information pertaining to the RAMS results of the products for which they are responsible.
This document is mainly concerned with the technical aspects, aspects of a legislative (in particular safety at work and regulatory conformity) and confidential nature are not dealt with in this document.

This document provides the means for understanding and associating the individual documents of the ISO/IEC 5259 series and is the foundation for conceptual understanding of data quality for analytics and machine learning. It also discusses associated technologies and examples (e.g. use cases and usage scenarios).

This document specifies a data quality model, data quality measures and guidance on reporting data quality in the context of analytics and machine learning (ML).
This document is applicable to all types of organizations who want to achieve their data quality objectives.

The purpose of this document is to provide customers and their suppliers with a document specifying the notions of product reliability "construction" and "management".
It offers programme directors and project managers information likely to help them:
-   determine the tasks to be performed and the application procedures, according to the specific nature of the programme and its goals;
-   define and implement the provisions necessary for performing these tasks;
-   within programme execution, situate the various tasks involved in constructing and managing the reliability of a product.
This document applies to all programmes (in particular aeronautical, space and armament programmes).
These reliability construction procedures concern not only all the products and its constituents covered by these programmes, but also the means and manufacturing processes to be implemented for their realization.
The provisions of this document can be negotiated at all levels between the parties directly concerned by a given programme. This implies, on the part of the customer, that each lower level is provided with the information necessary to perform tasks and meet the specified targets.

This Type C standard document is applicable for fixed and electric motor driven cableways operating as monocable or bicable aerial ropeways operating on a single-track or dual-track for the transport
-   of goods to supply goods to and dispose of waste from mountain huts and shelters and
-   of specially designated persons.
The particular characteristics of these cableways are their low usage (on average 6 trips per operating day), low speed (up to 4 m/s) and the limited group of people using the cableway. There is no transport obligation.
This document is not applicable to:
-   cableways primarily designed, constructed or operated mainly for the transport of persons and subject of Regulation (EU) 2016/424;
-   portable cableways;
-   lifts;
-   funicular railways;
-   fixed and portable equipment used exclusively for leisure and pleasure purposes and not for the transport of persons;
-   water ski lift installations;
-   agricultural and forestry installations;
-   rope crane installations and crane installations;
-   mining installations or other installations set up and used for industrial purposes;
-   drilling installations.
This document deals with the significant hazards arising from the construction and operation of the aforementioned cableways and measures to eliminate or reduce these hazards, provided that these cableways are used in accordance with their intended purpose and that the remaining residual risk has been anticipated and accepted by the manufacturer.
In the event that there are changes to the existing cableways, these changes are assessed in terms of their impact on safety in accordance with EN ISO 12100:2010. If this assessment shows that the intended changes do not constitute a significant change pursuant to the Machinery Directive, the requirements under this document are in all cases fulfilled by the assemblies/components.
In the following sections, for reasons of simplification, the term cableway is used on its own to cover the types of equipment covered by this standard.
This document does not cover:
-   hazards caused by noise in particular through the release of airborne sound;
-   hazards caused by vibration;
-   hazards caused by explosion;
-   hazards caused by electromagnetic influences (EMC).
NOTE 1 Directive 2014/30/EU regarding electromagnetic compatibility may be used for machinery or components in accordance with this document. This document is not intended as a means of proving compliance with the basic health and safety requirements of the aforementioned directive or the aforementioned hazards.
The requirements of this document do not apply for equipment and systems manufactured or placed on the market before the date of appearance of this document.

This document specifies the characteristics of multilayer mechanical locked floor covering with a wear-resistant and decorative surface layer supplied in panels (either tile or plank form). The floor panels are considered suitable for domestic and commercial levels of use and designed for floating installation.
This document does not apply to resilient floor panels for loose-laying according to EN ISO 20326, to multilayer wood floorings according to EN 13489, to wood veneer floor coverings according to EN 14354, to laminate floor covering according to EN 13329, EN 14978 and EN 15468 nor to products specified in EN ISO 10581, EN ISO 10582, EN ISO 24011, EN 12104 and ISO 14486.
This document is applicable to areas which are subject to frequent wetting, e.g. bathrooms, laundry rooms or saunas, only if specified by the producer.
This document also includes requirements for marking and packaging.
In Annex A (informative), optional properties are given. In Annex B (informative), a test method for the classification of the flexibility is given.

This document specifies a test method for determining the leak tightness and the ease of operation and stop resistance of a valve made of thermoplastic material following an impact applied to the operating device.

This document specifies requirements and provides guidance for establishing, implementing, maintaining and continually improving the quality of data used in the areas of analytics and machine learning.
This document does not define a detailed process, methods or metrics. Rather it defines the requirements and guidance for a quality management process along with a reference process and methods that can be tailored to meet the requirements in this document.
The requirements and recommendations set out in this document are generic and are intended to be applicable to all organizations, regardless of type, size or nature.

This document defines the following quantities commonly used to express the composition of gas mixtures:
—     amount fraction and concentration;
—     mass fraction and concentration;
—     volume fraction and concentration.
For these quantities of composition, this document specifies methods for:
—     conversion between different quantities;
—     conversion between different state conditions.
Conversion between different quantities means calculating the value of the content of a specified component in terms of one of the quantities listed above from the value of the same content, at the same pressure and temperature of the gas mixture, given in terms of another of these quantities. Conversion between different state conditions means calculating the value of the content of a specified component, in terms of one of the quantities listed above, under one set of state conditions from the value of the same quantity under another set of state conditions, i.e., pressure and temperature, of the gas mixture. Gas mixture composition can be converted simultaneously between different quantities of composition and different state conditions by combination of the two types of conversion.
This document is applicable only to homogeneous and stable gas mixtures. Therefore, any state conditions (pressure and temperature) considered need to be well outside the condensation region of the gas mixture. In addition, volume concentrations can only be used if the component under consideration is completely gaseous, and for the use of volume fractions, all components need to be completely gaseous. Further restrictions of state conditions apply for approximations of compression factors using virial coefficients (see Annex A).

This document establishes general common organizational approaches, regardless of the type, size or nature of the applying organization, to ensure data quality for training and evaluation in analytics and machine learning (ML). It includes guidance on the data quality process for:
—     supervised ML with regard to the labelling of data used for training ML systems, including common organizational approaches for training data labelling;
—     unsupervised ML;
—     semi-supervised ML;
—     reinforcement learning;
—     analytics.
This document is applicable to training and evaluation data that come from different sources, including data acquisition and data composition, data preparation, data labelling, evaluation and data use. This document does not define specific services, platforms or tools.

This document specifies the essential terms, constructional requirements, tests, energy assessment and marking of indirectly heated water storage tanks for primary water (buffer tanks), with a capacity not exceeding 2,000 l, an operating temperature not exceeding 95 °C, and an operating pressure not exceeding 1,0 MPa (10 bar).
This document covers metallic and plastic made buffer tanks.
Although this document does not consider any buffer tanks mainly intended for direct firing, it allows for the provision of electric heating elements for auxiliary purposes.
NOTE   The energy assessment is performed by EN 15332 or EN 12897.

EN 13611:2019, Clause 1 is applicable with the following modification and addition:
Modification:
The 1st paragraph of EN 13611:2019, Clause 1 is replaced by:
This document specifies the safety, design, construction, and performance requirements and testing for multifunctional controls for burners and appliances burning one or more gaseous fuels, hereafter referred to as ‘MFC’. This document is applicable to MFCs with declared maximum inlet pressures up to and including 50 kPa and nominal connection sizes up to and including DN 150.
Addition:
This document is applicable to MFCs consisting of two or more functions, at least one of which is a mechanical control, as specified in the relevant control standard (see Figure 1).
This document does not apply to MFCs consisting only of electronics (an example is a combination of functions according to EN 298:2022 and EN 1643:2022).
The 4th paragraph of EN 13611:2019, Clause 1 is removed.

This document provides a common approach and guidance to those undertaking assessment of the major safety hazards as part of the planning, design, and operation of LNG facilities onshore and at shoreline using risk-based methods and standards, to enable a safe design and operation of LNG facilities. The environmental risks associated with an LNG release are not addressed in this document.
This document is applicable both to export and import terminals but can be applicable to other facilities such as satellite and peak shaving plants.
This document is applicable to all facilities inside the perimeter of the terminal and all hazardous materials including LNG and associated products: LPG, pressurized natural gas, odorizers, and other flammable or hazardous products handled within the terminal.
The navigation risks and LNG tanker intrinsic operation risks are recognised, but they are not in the scope of this document. Hazards arising from interfaces between port and facility and ship are addressed and requirements are normally given by port authorities. It is assumed that LNG carriers are designed according to the IGC code, and that LNG fuelled vessels receiving bunker fuel are designed according to IGF code.
Border between port operation and LNG facility is when the ship/shore link (SSL) is established.
This document is not intended to specify acceptable levels of risk; however, examples of tolerable levels of risk are referenced.
See IEC 31010 and ISO 17776 with regard to general risk assessment methods, while this document focuses on the specific needs scenarios and practices within the LNG industry.

This document gives guidance on the use of colour codes to inform people at risk as well as first response personnel about danger and to express the severity of a situation.
This document is applicable to all types of hazard in any location.
This document does not apply to the method for displaying colour codes, detailed ergonomic considerations related to viewing displays or safety signs covered by ISO 3864-1.

ISO 2477:2005 describes a method for determining the permanent change in dimensions on heating of a shaped insulating refractory product.

This document defines fundamental terminology for blockchain and distributed ledger technologies.

This document specifies safety requirements for starting platforms with a height ≤ 750 mm above water level. These requirements are additional to those given in EN 13451-1 and these documents are intended to be read together.
The requirements of this specific standard take priority over those in EN 13451-1.
This document is applicable to starting platforms for use in classified swimming pools as specified in EN 15288-1 and EN 15288-2.

This document specifies a test method for the determination of the oxidation stability of fuels for diesel engines at 110 °C, by means of measuring the induction period of the fuel up to 48 h. The method is applicable to fatty acid methyl esters (FAME) intended for the use as pure biofuel or as a blending component for diesel fuels, and to blends of FAME with diesel fuel containing 2 % (V/V) of FAME at minimum.
The precision of the test method has been developed for conventional diesel. This test method is applicable for paraffinic diesel fuels as specified in EN 15940, however, a separate precision statement for paraffinic diesel is not available.
NOTE 1   EN 14112 [1] describes a similar test method for the determination of the oxidation stability of pure fatty acid methyl esters (see the Introduction to this document). Additionally, EN 16568 [4] describes a similar test method for the determination of the oxidation stability of fuels for diesel engines at 120 °C, by means of measuring the induction period of the fuel up to 20 h. EN 16568 is applicable to blends of FAME with diesel fuel containing 2 % (V/V) of FAME at minimum. Other alternative test methods for the determination of the oxidation stability of distillate fuels are described in CEN/TR 17225 [5].
NOTE 2   For induction periods higher than 48 h the precision is not covered by the precision statement of this method. The limit values of the relevant fuel standards are well within the scope of this test method.
NOTE 3   The presence of cetane improver can reduce the oxidation stability determined by this test method. Limited studies with EHN (2-ethyl hexyl nitrate) indicated, however, that the stability is reduced to an extent which is within the reproducibility of the test method.
NOTE 4   For the purposes of this document, the term “% (V/V)” is used to represent the volume fraction (φ) of a material.

This document specifies a method to determine the influence of site-applied cement based materials and associated non-cement based products/materials (including pre-packaged mortars) on the odour, flavour, colour, turbidity and total organic carbon (TOC) of test waters after contact with the products.
This document is applicable to site-applied or site-formed cement based materials intended to be used for the transport and storage of water intended for human consumption, including raw water used for the production of drinking water. It is also applicable to individual constituents of cement based products/materials and to associated non-cement based products/materials.
Site-applied or site-formed cement based materials which cannot be cast as cubes or prisms e.g. some spray applied systems, should be tested as factory made cement based products according to EN 14944−1.
NOTE   Tests with the specified test water will not necessarily be representative of materials used in different kinds of waters and especially very soft waters.

This document specifies the requirements and test methods for temporary edge protection systems for use during construction or maintenance of buildings and other structures.
This document applies to edge protection systems for flat and inclined surfaces and specifies the requirements for three classes of temporary edge protection.
For edge protection systems with an arrest function (e.g. falling or sliding down a sloping roof) this document specifies requirements for energy absorption.
This document includes edge protection systems, some of which are fixed to the structure and others, which rely on gravity and friction on flat surfaces.
This document does not provide requirements for edge protection systems intended for:
—   protection against impact from vehicles or from other mobile equipment,
—   protection from sliding down of bulk loose materials, snow etc,
—   protection of areas accessible to the public.
This document does not apply to side protection on scaffolds according to EN 12811 1 and EN 1004 1.
NOTE   This does not prevent these systems to be used on temporary structures.

This document establishes an approach and methodology for a country-based mechanism to channel climate finance to subnational
authorities to support climate change adaptation and to increase local resilience thereby contributing to the achievement of the goals
of the 2015 Paris Agreement of the United Nations Framework Convention on Climate Change (UNFCCC) and the UN Sustainable
Development Goals (SDGs). The country-based mechanism uses performance-based climate resilience grants (PBCRGs) which
ensure programming and verification of climate change expenditures at the local level, offering strong incentives for performance
improvements in enhanced resilience.
This document provides requirements and guidelines and is applicable to organizations such as national and subnational authorities,
donors, companies, financial institutions and international organizations that are involved in implementing a country-based
mechanism for channelling climate finance to subnational authorities to support climate change adaptation and resilience.
NOTE Another mechanism for supporting local adaptation is by direct support at the local level by donors without any financial
flows from national government.

This document gives guidance and requirements for the assessment of conformity of compounds/formulations, products, joints and assemblies in accordance with the applicable part(s) of EN 14758 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE 1   A basic test matrix provides an overview of the testing scheme in Annex A, Table A.1.
NOTE 2   If certification is involved, the certification body operating according to EN ISO/IEC 17065 [1] and EN ISO/IEC 17020 [2] is considered to be competent.
In conjunction with EN 14758-1, this document is applicable to solid wall pipes and fittings with or without internal and/or external skin and the system made of mineral modified polypropylene materials (PP-MD) intended to be used for non-pressure underground drainage and sewerage:
-   outside the building structure (application area code “U”); and
-   for both buried in ground within the building structure and outside the building structure (application area code “UD”).

This document specifies basic requirements for hydraulic part-turn valve actuators, both double acting and single acting, used for on-off and modulating control duties.
It includes guidelines, recommendations and methods for enclosure and corrosion protection, control and testing.
It does not apply to hydraulic actuators which are integral parts of control valves and to hydraulic actuators designed for permanent immersion in fresh or sea water as well as electro-hydraulic actuators.
Other requirements, or conditions of use, different from those indicated in this document can vary upon request.

This document specifies the requirements for the design, manufacture and testing of cylinders, tubes and other pressure vessels of steel, stainless steel, aluminium alloys or of non-metallic construction material. These are intended for the stationary storage of gaseous hydrogen of up to a maximum water capacity of 10 000 l and a maximum allowable working pressure not exceeding 1 100 bar, of seamless metallic construction (Type 1) or of composite construction (Types 2, 3 and 4), hereafter referred to as pressure vessels.
NOTE   Additional requirements with regard to assemblies (manifolded cylinders and tubes and other pressure vessels) are not covered by this document.
This document is not applicable to Type 2 and 3 vessels with welded liners.
This document is not applicable to pressure vessels used for solid, liquid hydrogen or hybrid cryogenic-high pressure hydrogen storage applications.
This document is not applicable to external piping which can be designed according to recognized standards.

This document specifies a test method and the minimum requirements for bactericidal activity of chemical disinfectant and antiseptic products that form a homogeneous, physically stable preparation when diluted with hard water or - in the case of ready-to-use-products - with water.
This document applies to products that are used in the veterinary area for disinfecting non-porous surfaces without mechanical action - i.e. in the breeding, husbandry, production, veterinary care facilities, transport and disposal of all animals except when in the food chain following death and entry to the processing industry.
EN 14885 specifies in detail the relationship of the various tests to one another and to "use recommendations".
NOTE 1   The method described is intended to determine the activity of commercial formulations or active substances in the conditions in which they are used.
NOTE 2   This method corresponds to a Phase 2 Step 2 test.
This method excludes the evaluation of the activity of products against yeasts, fungal spores, mycobacteria and bacterial spores.

This document specifies a tensile bending method and a compression bending method for determining the failure stress of welded corners and welded T-joints made from unplasticized poly(vinyl chloride) (PVC-U) profiles.
It is applicable to PVC based profiles used for the fabrication of windows and doors.

This document specifies requirements and test methods for the fire safety of candle accessories, as well as safety information ‎and requirements on how safety information will be displayed.
The safety requirements and test methods specified in this document are intended to cover the most common risks.
This document does not specify requirements or test methods for uncommon risks arising from the unforeseen combination of accessories and candles.
This document does not apply to birthday cake candle holders that can hold only one candle and do not contain pyrotechnics.

This document specifies guidelines for a use of social media in emergency management. It gives
guidance on how to use social media before, during and after an emergency and how social
media can support the work of emergency services. On the one hand, these guidelines are directed to
authorities (governmental as well as non­governmental organisations) involved in emergency management.
On the other hand, they are directed to citizens who want to use social media in emergency
situations.
These guidelines shall help social media users to use these new media as efficiently as possible.

This document specifies requirements and test methods for the physical properties of powered toothbrushes in order to promote the safety of these products for their intended use.
There are different technologies of powered toothbrushes. Common features of those powered toothbrushes to which this document applies are:
—     a battery;
—     a motor;
—     a mechanical or magnetic drive system;
—     a moving brush head with tufted filaments.
Powered toothbrushes can have a moving brush head with different motions (e.g. oscillating-rotating, side-by-side), frequencies and velocities.
These types of electric toothbrushes are tested for safety in use by means of appropriate test procedures or clinical studies
The requirements listed in this document apply to all types of powered toothbrushes. However, there is a possibility that some requirements are not applicable for all types. For example, brush head plate retention can only be applied if the brush has a head portion that can detach from the brush shaft. In addition, for the filaments end-rounding requirements, this document does not apply to filament types that are very thin (less than 0,1 mm outside diameter) or have no sharp edges (e.g. tapered, feathered, with split tips or spherical cap) or non-synthetic filaments, where applying the end-rounding process is inappropriate or impossible.
This document is not applicable to other types of powered oral hygiene devices (such as powered interdental brushes) or manual toothbrushes.

This NWI Will be a TS and will specify additional requirements for qualified or not qualified trust services implementing electronic archiving service with specific regard to :
•   Functional requirements to use for receipt, storage, retrieval and deletion to ensure that the electronic data and electronic documents (electronically-born documents  and paper documents that have been scanned and digitized) are preserved in such a way that they are accessible and durably safeguarded against loss and unauthorized alteration or disposal, except for authorized changes concerning their electronic format.
•   Procedures and technologies ensuring the accuracy of the origin, the durability and legibility, integrity of the electronic data and electronic documents beyond the technological validity period and at least throughout the legal or contractual preservation period, while maintaining their integrity and their origin.
•   Procedures and technologies to use to allow authorised relying parties to receive a report in an automated manner that confirms that an electronic data  and electronic documents retrieved from a qualified electronic archive enjoys the presumption of integrity of the data and electronic documents from the beginning of the preservation period to the moment of retrieval.
•   Procedures and technologies to prevent unauthorized access and improper use of the confidential and restricted data and electronic documents.
•   Interactions between electronic archiving trust services and other trust services.
•   Procedures and technologies to reach and obtain a green sustainability approach when possible.

This document establishes requirements, test procedures, assessment methods and acceptance criteria for operating rolling stock in open track. For pressure variations and slipstream effects beside the track, requirements and assessment methods are provided. For running resistance, assessment methods are addressed in this document. Load cases on infrastructure components due to train-induced pressure variations and slipstream effects are addressed in this document. For ballasted track test set-ups for ballast projection assessment are proposed.
The requirements only apply to rolling stock of the heavy rail system with maximum train speeds above 160 km/h and not to other rail systems. The document is applicable to all rolling stock and infrastructure in open air with nominal track gauges of 1 435 mm to 1 668 mm inclusive.

This document specifies a method to determine the migration of substances from hardened cement based site-applied or site-formed materials (including pre-packaged mortars) into test waters after contact with the products. It also covers determination of migration from individual constituents of cement based products and materials (see Annexes A and B) and from associated non-cement based products for approval purposes (see Annex C).
Site-applied or site-formed cement based materials which cannot be cast as cubes or prisms e.g. some spray applied systems, fall in the scope of EN 14944−3 and not under this standard.
This document is applicable to site-applied or site-formed cement based materials intended to be used for the transport and storage of water intended for human consumption, including raw water used for the production of drinking water. It is also applicable to individual constituents of cement based products/materials and to associated non-cement based products/materials.
NOTE   Tests with the specified test water will not necessarily be representative of materials used in different kinds of waters and especially very soft waters.

This document specifies the requirements for washer-disinfectors (WD) intended to be used for the cleaning and chemical disinfection, in a single operating cycle, of reusable items such as:
a)       bed frames;
b)       bedside tables;
c)        transport carts;
d)       containers;
e)       surgical tables;
f)         sterilization containers;
g)       surgical clogs;
h)       wheelchairs;
i)         aids for persons with disabilities.
This document also specifies the performance requirements for the cleaning and disinfection of the WD and its components and accessories.
Devices identified within the scopes of ISO 15883-2, ISO 15883-3, ISO 15883-4, and ISO 15883-6 do not fall within the scope of this document.
In addition, this document specifies the methods for type testing, works testing, validation (installation, operation, and performance qualification on first installation), routine control, and monitoring, as well as requalifications to be carried out periodically and after essential repairs.
NOTE 1        WD covered by this document can also be used for cleaning and chemical disinfection of other thermolabile and reusable devices as recommended in the instructions for use (IFU) for those devices.
NOTE 2        The performance requirements specified in this document cannot ensure the inactivation or removal of the causative agent(s) (prion proteins) of transmissible spongiform encephalopathies.

This document specifies the requirements for the effective control of non-deliverable software. This document can be used during the design, development, test, production, release, use, maintenance, and retirement of non-deliverable software. This can include non-deliverable software procured from external suppliers and utilized in the design, production, evaluation, test, acceptance, or calibration of a deliverable product.
This document focuses solely on the unique requirements of the operational processes that pertain to non-deliverable software as identified below:
This document applies to non-deliverable software (including firmware) that affects a deliverable product or service. Following are several applications and supporting examples of non-deliverable software that is within the scope of this document:
—   design and development: modelling, simulation, virtual reality, virtual machine, computer-aided design (CAD), three-dimensional (3D) modelling and analysis tools, software compiler, and code generators;
—   manufacturing: additive manufacturing, computer numerical controlled (CNC) programs, robotics, factory automation, tools that load deliverable software, software used in special process (e.g. heat treat, shot peen, sonic wall inspection), and automated manufacturing software (i.e. pick and place);
—   verification, validation and maintenance: coordinate measuring machine (CMM) programs, hardware or software qualification, code coverage, test scripts, analysis tools, acceptance test, production acceptance, calibration (inspection, test or calibration), simulator, emulator, and software used in post-delivery service provisions.
The following types of software are not within scope of this document:
—   deliverable software (refer to EN 9115);
—   manufacturing and measuring equipment embedded software (e.g. operating system, drivers);
—   enterprise or office software (e.g. MS Office, word processing or spreadsheet applications, Teams, network software, email, employee management system).
Operational processes not covered in this document are addressed by the respective organization’s quality management system (QMS), based on the EN 9100-series (i.e. EN 9100, EN 9110, EN 9120) and/or ISO 9001 standards.