DIREKTOR - THE DIRECTOR

Unchanged with respect to the current edition CLC/TS 50459-2:2015.
Scope of the revision:
- to update general principles for the presentation of ERTMS/ETCS/GSM-R information correlated with ERA_ERTMS_015560 v3.4.0:2016,
- to update ergonomic arrangements with EN 16186-1:2014, EN 16186-2:2017, EN 16186-3:2016
- to harmonize layout with existing and on supplier side well-established solutions and enhancement of touch-layout
- to update in accordance to the Results of the outcome of the Rascop DMI ad’hoc group

This document specifies the method for assessing overall exposure from all fixed radio frequency sources at a broadcast site. This assessment can be applied at any time but is carried out when the exposure situation changes in or around the aforementioned site.
This document plays an essential role in the coordination of different stakeholders, with respect to ensuring EMF exposure compliance in and around a broadcast site especially for equipment installed within the site.

This European Standard specifies a test method for the micro-scratch resistance with two procedures (A and B) and a test method for polishing resistance (procedure C) which can be used for all types of laminate floor coverings. The resistance to polishing is related to mat surfaces.

This International Standard specifies a classification system for solid recovered fuels (SRF)
and a template for the specification of their properties.
SRF are produced from non-hazardous waste.
Excluded:
— untreated municipal solid waste
— Solid Biofuels included in the scope of ISO TC238

This standard specifies a method for the measurement of iron-55 and nickel-63 (55Fe and 63Ni)in all types of waters by liquid scintillation counting (LSC).
The detection limit depends on the sample volume and the instrument used. The test method described in this standard is based on currently available LSC counters.

DEN/ERM-TGAERO-42-1

DEN/ERM-TGAERO-42-3

DEN/ERM-TGAERO-42-2

REN/ERM-TG17-162

DTS/ESI-0019182-1

DOW = DAV+36 months

This document specifies requirements and their test methods for tissue punches used with a handpiece in dentistry especially for oral surgical implant procedures such as cutting holes or notches in and removing of gingival tissue. It also specifies the requirements for their marking and labelling.

This part of ISO 23036 specifies a method that is applicable for the detection of Anisakidae L3 larvae commonly found in marine and anadromous fishes. The method can be applied to fresh fish and/or frozen fish, lightly processed fish products, such as marinated, salted or smoked, and it’s also suitable for visceral organs as confirmatory method for visual inspection scheme.
The artificial digestion method allows quantifying parasitic infections by estimating the number of parasites in the fish musculature and, when applied to fresh fish or lightly processed fish products (never frozen before processing), determining the viability of Anisakidae L3, which may be present.
This method doesn’t allow determining species or genotype of detected parasites, which identification is made by morphological and/or molecular methods.

This part of ISO 23036 specifies a method that is applicable for the detection of Anisakidae L3 larvae commonly found in marine and anadromous fishes. The method can be applied to fresh fish and/or frozen fish, lightly processed fish products, such as marinated, salted or cold smoked.
This method allows quantifying parasitic infections by estimating the number of parasites in the fish musculature.
This method doesn’t allow determining species or genotype of detected parasites, which identification
is made by morphological and/or molecular methods

2021-04-15 HD: Through Decision BT C067/2021, BT approved revised Annex ZA after Formal Vote

This document covers the preanalytical phase and recommends the handling, documentation and processing of urine, venous blood plasma and serum intended for metabolomics analysis.
The document is applicable to metabolomics examinations and is of importance to biomedical laboratories, customers of laboratories, in vitro diagnostics developers and manufacturers, institutions and companies performing biomedical research, biobanks, and regulatory authorities. The adoption of the described procedures for the preanalytical phase make it possible to compare and evaluate the results obtained from metabolic profiling analysis.
NOTE International, national or regional regulations or requirements can also apply to specific topics covered in this document.

The aim of the present standard is to determine the time necessary to disintegrate a test piece of toilet
paper, in specified conditions.
This test method is applicable to every type of toilet paper, with exception to papers used in toilets with
a specific way of paper removal [for example watertight chemical toilets in some means of transport:
see NF F 31-829 (French standard)].
Removal problems encountered in this latter case may then justify a greater degree of resistance of
the product and thus a very long disintegration time, or even no disintegration at all.

This document specifies the characteristics of electrical cables for use in the on-board electrical systems of aircraft at operating temperatures between -55 °C and 260 °C for cross sections equal to and greater than 5 mm2.

This International Standard specifies a chromatographic method to determine the amount of middle-chain chlorinated paraffins (MCCP) C14-C17 in processed and unprocessed leather.

This European Standard introduces methods and procedures when applying physical asset management as a framework to take into account the maintenance function within organisations strategic and tactical decision on physical assets and when applying physical asset management as a framework to maintenance activities. It also introduces at a methodological level the relationship between organizational strategic plan and the maintenance management system and describes at a procedural level the interrelations between maintenance process and all the other physical asset management processes.
This European Standard may be applied to managing the physical assets of organizations of all sizes especially goods producing organisations. However, if specific standards exist for a particular application, those standards may also be considered.
This European standard introduces methods and procedures for all the levels and functions of the organisations’ management such as corporate planning management, plant management, technical management, production management, financial management, asset management, maintenance management, quality management etc.
This European Standard consists of guidance and recommendations and is not intended to be used for
certification, regulatory, or contractual use.

This document specifies a procedure for the determination of the citrinin content in food (cereals, red yeast rice (RYR)), herbs and food supplements by liquid chromatography tandem mass spectrometry (LC-MS/MS).
This method has been validated for citrinin in red yeast rice and in the formulated food supplements in the range of 2,5 µg/kg to 3000 µg/kg and in wheat flour in the range of 2,5 µg/kg to 100 µg/kg.
Laboratory experiences have shown that this method is also applicable to white rice, herbs such as a powder of ginkgo biloba leaves and the formulated food supplements in the range of 2,5 µg/kg to 50 µg/kg.

The purpose of this document is to provide innovative requirements and test methods applicable to any components and assemblies of any category of bicycles (city, trekking, MTB, young adult and racing). Its aim is to provide technical solutions that reduce the risk of component failure and rider injury during the specified use of such bicycles.
This document makes reference to current "state of the art" standards in the field of bicycles, agreed at CEN level through the publication of the EN ISO 4210 series of standards. Therefore, the requirements and tests proposed in this document are intended to be read and applied in accordance with the appropriate EN ISO 4210 standard.
NOTE   The tests described in this document refer in places to clause numbers from the applicable EN ISO 4210 series.

This document specifies a method for measuring the scratch resistance and failure behaviour for advanced materials and coatings by means of nano- and micro- scale scratch experiments. The method provides data on both the physical damage to test-pieces and the friction generated between the probe and the test-piece under single pass and multiple pass conditions. The force range in these tests is from 1 µN up to 2 N.
The test method is not applicable to coatings as defined in EN ISO 4618 [18].

This document describes a test method for carrying out road trials on retroreflecting road studs for use in permanent applications. Specifications are given for test sites and for application patterns, and a recommendation is given for the presentation of the results in the form of a test report.
Temporary road studs are covered in Annex D (informative).

This document deals with Portland-composite cement CEM II-C/M, not covered by EN 197-1, and a new type of Composite cement CEM VI, also not covered by EN 197-1, whose intended use is the preparation of concrete, mortar, grout etc.
This document does not cover:
-   common cement covered by EN 197-1;
-   very low heat special cement covered by EN 14216;
-   supersulfated cement covered by EN 15743;
-   calcium aluminate cement covered by EN 14647;
-   masonry cement covered by EN 413-1.

This European Standard specifies the technical delivery conditions for forgings for pressure purposes, made of weldable fine grain steels with high proof strength.
NOTE   Once this standard is published in the EU Official Journal (OJEU) under Directive 2014/68/EU, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 2014/68/EU is limited to technical data of materials in this standard and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 2014/68/EU are satisfied, needs to be done. The series EN 10222-1 to EN 10222-5 is structured so that the data related to different materials is in the part allocated for that material. The presumption of conformity to the Essential Safety Requirements of Directive 2014/68/EU depends on both the text in part 1 and the data in part 2, 3, 4 or 5.
General information on technical delivery conditions is given in EN 10021.

This part of this European Standard specifies the technical delivery conditions for forgings for pressure purposes, made of ferritic and martensitic steels with specified elevated temperature properties. Chemical composition and mechanical properties are specified.
NOTE   Once this standard is published in the EU Official Journal (OJEU) under Directive 2014/68/EU, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 2014/68/EU is limited to technical data of materials in this standard and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 2014/68/EU are satisfied, needs to be done. The series EN 10222-1 to EN 10222-5 is structured so that the data related to different materials is in the part allocated for that material. The presumption of conformity to the Essential Safety Requirements of Directive 2014/68/EU depends on both the text in part 1 and the data in part 2, 3, 4 or 5.
General information on technical delivery condition is given in EN 10021.

This standard specifies a Chromatographic method for the determination of short-chain chlorinated paraffins (SCCP) in leather

N/A

N/A

This European Standard specifies the composition, property requirements including electrical properties, and tolerances on dimensions and form for copper rod, bar and wire for general electrical purposes. Cross sections and size ranges are:
-   round, square and hexagonal rod with diameters or widths across flats from 2 mm up to and including 160 mm;
-   bar with thicknesses from 2 mm up to and including 40 mm and widths from 3 mm up to and including 250 mm;
-   round, square, hexagonal and rectangular wire with diameters or widths across flats from 2 mm up to and including 25 mm, as well as thicknesses from 0,5 mm up to and including 12 mm with widths from 1 mm up to and including 250 mm.
The sampling procedures and test methods for verification of conformity to the requirements of this standard are also specified.
NOTE   Drawn, round copper wire - plain or tinned, single or multiline - for the manufacture of electrical conductors is specified in EN 13602.

This document specifies test methods for the determination of bearing capacity (ultimate limit state and serviceability limit state), of connections between curtain walling framing members for which it cannot be calculated in accordance with current codes or conventional calculations based upon the strength of the materials.
Mechanical performances of the curtain walling connections are already assessed in accordance with the provisions described in EN 13830. Additional information with respect to mechanical performance of the connections and direct applications can be determined with this document.

The document specifies, dimensions, materials and performance requirements (including methods of test) for expansion groups, of nominal sizes from DN 15 to DN 25, having working pressures ) from 0,1 MPa (1 bar) to 1,0 MPa (10 bar).
Expansion groups shall be fitted to the cold potable water supply only for expansion purposes, e.g. of storage water heaters, having a maximum distribution temperature of 95 °C.
Expansion groups limit pressure in the water heater to which they are fitted, that is produced by thermal expansion of the water, prevent the backflow of water into the supply pipe and prevent the discharged water to get into contact with the water in the water heater.
Expansion groups do not control temperature and alone do not constitute the protection required for storage water heaters.
NOTE   The use of the device specified in this Standard does not override the need to use controls (e.g. thermostats and thermal cut-outs) which act directly on the power sources of water heaters.

This European Standard specifies methods for assessing the tin coating on drawn round copper wire for the manufacture of electrical conductors, e.g. according to EN 13602.
This European Standard includes test methods for the determination of the following characteristics:
a)   thickness of the unalloyed tin coating;
b)   continuity of the tin coating;
c)   adherence of the tin coating.
WARNING - This European Standard can involve the use of hazardous materials, operations, and equipment. This standard does not purport to address all of the safety problems associated with their use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

This document specifies a test method for the determination of resistance to manual burglary attempts in order to assess the burglar resistant characteristics of pedestrian doorsets, windows, curtain walling, grilles and shutters. It is applicable to the following means of opening: turning, tilting, folding, turn-tilting, top or bottom hung, sliding (horizontally and vertically), pivoted (horizontally and vertically) and rolling as well as fixed constructions.
This document does not directly cover the resistance of locks and cylinders to attack with picking tools. It also does not cover the attack of electric, electronic and electromagnetic operated burglar resistant construction products using attack methods that might defeat these characteristics.
The manufacturer's installation instructions will give guidance on the fixing of the product.
An example for the contents of the manufacturer’s installation instructions is given in Annex A of prEN 1627:2019.
This document does not apply to doors, gates and barriers, intended for installation in areas in the reach of persons, and for which the main intended uses are giving safe access for goods and vehicles accompanied or driven by persons in industrial, commercial or residential premises, as covered by EN 13241.
It is acknowledged that there are two aspects to the burglar resistance performance of construction products, their normal resistance to forced operation and their ability to remain fixed to the building. This test method does not evaluate the performance of the fixing to the building.