Search Catalog

This document is applicable to all water slides installed at open water areas for public use or in swimming pools for public use.
This document specifies general safety requirements for water slides installed at open water areas for public use or in swimming pools for public use and specific requirements for defined types of water slides. These specific safety requirements are also applicable to undefined types as far as possible.
These requirements concern safety and the technical rules for design, calculation and testing.

This document provides a method of describing the materials, impregnates and lubricants for various types of yarn and ribbon based packings intended for use as gland seals in mechanical equipment such as pumps, mixers, etc. This document is intended to serve as a guide for packing manufacturers, pump OEM’s and end users. It does not include similar products intended for other duties such as thermal insulation.
Guidance is also given regarding dimensional and physical quality aspects of the packings and requirements for packaging and marking.
Tests are specified for the determination of lubricant content, size and mass.
NOTE 1   The information supplied by the purchaser at the time of enquiry and/or order is given in Annex B.
NOTE 2   All packings are free from introduced asbestos fibres in conformance with Annex XVII of REACH.

This document specifies two methods for the determination of the tear strength of flexible cellular polymeric materials:
Method A, using a trouser test piece;
Method B, using an angle test piece without a nick.

This document describes the technical features of parcel boxes for end use. This covers technical features such as size of parcels, ergonomics and safety, corrosion and water penetration resistance and security of delivery.

This part of the EN 13451 series specifies safety requirements for diving platforms, diving springboards and associated equipment in addition to the general safety requirements of EN 13451-1 and is meant to be read in conjunction with it.
The requirements of this part of the EN 13451 series take priority over those in EN 13451-1.
This part of the EN 13451 series is applicable to platforms and springboards, and associated equipment for use in classified swimming pools as specified in EN 15288-1 and EN 15288-2.

This document specifies requirements, test methods, marking and information to be supplied for autobelay devices, intended to protect against falls during recreational use in a climbing structure. An autobelay device is a movable personal fall protection system for single person use.
This document does not specify requirements for descender devices or retractable fall arresters that are used for descending/climbing in mountaineering, rescue, rope access, fall arrest or work positioning systems.
NOTE 1   A climbing structure is e.g. a ropes course, a climbing gym.
NOTE 2   An autobelay device which enables the user to belay and descent himself/herself and which conforms to this document is personal protective equipment (PPE).
NOTE 3   For mountaineering standards, see Annex E.

This document is applicable to all water slides installed at open water areas for public use or in swimming pools for public use.
This document establishes the instructions for use, operation, and maintenance as well as the documentation of water slides.

This document specifies the fundamental principles and concepts of conformity assessment schemes (programmes) and provides guidelines for understanding, developing, operating or maintaining them.

This document specifies calculation and verification methods for evaluating the spill light coming from the electric light sources of lighting installations in public and non-public outdoor areas, in the following application fields:
-   lighting installations in outdoor workplaces (ref. EN 12464-2);
-   road lighting installations (ref. CEN/TR 13201-1, EN 13201 series);
-   lighting installations for outdoor sports fields and areas (ref. EN 12193);
-   monument and architectural lighting installations;
-   lighting installations for the outdoor areas of residential buildings;
-   lighting installations for the outdoor areas of parks and gardens.
This document also considers luminous signs and luminous advertising installations in outdoor areas and the light emission from illuminated environments covered by translucent surfaces.
With the exception of lighting installations within premises located and designed for observation from exterior observers light emitted from windows, skylights and shop windows are excluded.
The calculation methods described are intended as an integral part of the lighting design and are suitable for evaluating consistency with any regulatory conditions.
Due to the complexity of the phenomena and the numerous variables, this document does not consider the influence of atmospheric conditions in evaluating obtrusive light.
This document does not apply to lighting installations for tunnels and underpasses and to all signalling devices such as traffic lights, active road signs and the like, or to vehicle headlamps.
This document additionally considers the spectral composition of the light concerned, as well as the room brightening at building openings not intentionally lit in the above application areas and any glare effects from these.

This document provides complementary product category rules (c-PCR) for Type III environmental product declarations (EPD) for flat glass and channel shaped glass products for use in buildings and construction works. It describes stages of product’s life cycle considered in the EPD and the processes included in life cycle stages.
Glass-block products are excluded from the scope. All other glass products i.e. intermediate and finished products, intended to be used in buildings and construction works, are in the scope of this document.
Examples of glass products covered by this c-PCR are listed in Annex H.

This document defines the terms and specifies the requirements, means of categorization, test methods, minimum labelling requirements and instructions for use of the article, for ignition devices (except ignition devices for pyrotechnic articles for vehicles) of the following generic types:
-   igniters;
-   components for pyrotechnic trains;
-   pyrotechnic cords and fuses;
-   delay fuses;
-   fuzes.
NOTE   Safety fuses are subject to Directive 2014/28/EU [9] and therefore not considered in this document.

This document specifies minimum requirements applicable to design, final assessment, designation, marking and documentation for butterfly valves having metallic bodies for use with all type of pipe end connections (e.g. wafer, lug, flange, butt welding, threaded ends) and used for isolating, regulating or controlling applications.
The PN and Class ranges are:
-   PN 2,5; PN 6; PN 10; PN 16; PN 25; PN 40; PN 63; PN 100; PN 160;
-   Class 150; Class 300; Class 600; Class 900.
The size range is:
-   DN 20; DN 25; DN 32; DN 40; DN 50; DN 65; DN 80; DN 100; DN 125; DN 150; DN 200; DN 250; DN 300; DN 350; DN 400; DN 450; DN 500; DN 600; DN 700; DN 750; DN 800; DN 900; DN 1 000; DN 1 050; DN 1 100; DN 1 200; DN 1 400; DN 1 500; DN 1 600; DN 1 800; DN 2 000; DN 2 200; DN 2 400; DN 2 600; DN 2 800; DN 3 000; DN 3 200; DN 3 400; DN 3 600; DN 3 800; DN 4 000.
DN 750 and DN 1 050 apply only for Class 150 and Class 300.
NOTE   Sizes are listed in Table D.1.
For applications in accordance with the European legislation for pressure equipment, EN 16668:2025 applies together with this document.
For chemical applications, EN 12569:2020 applies together with this document.
For gas distribution systems, EN 13774:2013 applies together with this document.
For gas transport systems, EN 1594:2024 applies together with this document.
For water supply application, EN 1074-2:2000 applies together with this document.
For process control application, EN 1349:2009 applies together with this document.
The correspondence between DN and NPS is given for information in Annex D.

This document specifies the fundamental aspects of semantic interoperability for the S2 interface and the related data exchange between a CEM and the resource managers within the premises. It provides a technology independent set of data models and interaction patterns in order to enable applications for energy management within the premises. This document does not include:
– mappings to concrete data representations (XML, JSON and similar);
– mappings to application protocols for the message passing;
– security related aspects.
This group EE publication is primarily intended to be used as an EE standard for the products mentioned in the scope, but is also intended to be used by TCs in the preparation of publications for products which are included in the boundary mentioned in the scope of this document.

This document specifies the design, testing and marking requirements for spring loaded pressure relief valves (PRV), for use in liquefied petroleum gas (LPG) cylinders of water capacity of 0,5 l up to and including 150 l.
These PRVs can be either an integral part of a cylinder valve (see EN ISO 14245 [4] and EN ISO 15995 [5]) or a separate device.

The scope of this part of IEC 62351 is to facilitate role-based access control (RBAC) for power system management. RBAC assigns human users, automated systems, and software applications (collectively called "subjects" in this document) to specified "roles", and restricts their access to only those resources, which the security policies identify as necessary for their roles.
As electric power systems become more automated and cyber security concerns become more prominent, it is becoming increasingly critical to ensure that access to data (read, write, control, etc.) is restricted. As in many aspects of security, RBAC is not just a technology; it is a way of running a business. RBAC is not a new concept; in fact, it is used by many operating systems to control access to system resources. Specifically, RBAC provides an alternative to the all-ornothing super-user model in which all subjects have access to all data, including control commands.
RBAC is a primary method to meet the security principle of least privilege, which states that no subject should be authorized more permissions than necessary for performing that subject’s task. With RBAC, authorization is separated from authentication. RBAC enables an organization to subdivide super-user capabilities and package them into special user accounts' termed roles for assignment to specific individuals according to their associated duties. This subdivision enables security policies to determine who or what systems are permitted access to which data in other systems. RBAC thus provides a means of reallocating system controls as defined by the organization policy. In particular, RBAC can protect sensitive system operations from inadvertent (or deliberate) actions by unauthorized users. Clearly RBAC is not confined to human users though; it applies equally well to automated systems and software applications, i.e., software parts operating independent of user interactions.
The following interactions are in scope:
– local (direct wired) access to the object by a human user, a local and automated computer agent, or a built-in human machine interface (HMI) or panel;
– remote (via dial-up or wireless media) access to the object by a human user;
– remote (via dial-up or wireless media) access to the object by a remote automated computer agent, e.g., another object at another substation, a distributed energy resource at an enduser’s facility, or a control centre application.
While this document defines a set of mandatory roles to be supported, the exchange format for defined specific or custom roles is also in scope of this document. This is achieved by defining two different encoding approaches to handle the definition of custom roles, either based on specific permissions or based on constraints to existing permissions. The definition on handling custom based roles was started in IEC 62351-90-1 and taken over into the IEC 62351-8:2020. Moreover, additionally to the definition of custom roles based on associated permissions, this document also includes options how to assign permissions to objects in a general way. Referencing documents will provide a mapping to a concrete data model to ensure an interoperability for standard roles used in different data models as well as for custom defined roles. Referencing documents might be standards such as IEC PAS 61850-90-19 or IEC 60870-5-7:2025 or also definitions by an operator.
Out of scope for this document are all topics which are not directly related to the definition of roles and access tokens for local and remote access, especially administrative or organizational tasks, such as:
– definition of usernames and password definitions/policies;
– management of keys and/or key exchange;
– engineering process of roles;
– assignment of roles;
– selection of trusted certification authorities issuing credentials (access tokens);
– defining the tasks of a security officer;
– integrating local policies in RBAC.
NOTE Specifically, the manage

This document specifies calculation methods for determining the required mass flow to be relieved for each specified conditions described in Table 1.
Recommendations for pressure relief devices for cryostats are given in Annex A.

This part of IEC 61851 applies to the EV supply equipment to provide energy transfer between the supply network and electric vehicles (EVs), with a rated maximum voltage at side A (supply network side) up to 1 000 V AC or up to 1 500 V DC and a rated maximum voltage at side B (EV side) up to 1 250 V DC.
NOTE A rated maximum voltage of the EV supply equipment at side B of up to 1 500 V DC is under consideration.
This document specifies the EV supply equipment of megawatt charging system (MCS) equipped with a coupler according to IEC TS 63379. Systems different to MCS using a coupler specified in IEC TS 63379 are under consideration.
The requirements for bidirectional power flow systems are under consideration.
This document does not cover all safety aspects related to maintenance.
This document specifies systems with protective separation between side A and side B.
The requirements for digital communication between the EV supply equipment and the EV for control of energy transfer are defined in ISO 15118-10 and ISO 15118-20.
EV supply equipment in compliance with this document is not intended to provide energy transfer to a single EV using
– multiple vehicle connectors of the same EV supply equipment, or
– multiple EV supply equipment.
The requirements for such use cases are not specified in this document but are under consideration.
The requirements for EVs mated to EV supply equipment according to this document are specified in ISO 5474-3:2024, Annex B.

This document a) addresses the support of safety extra low voltage (SELV) and limited power source (LPS) applications that provide remote power over: - 4-pair balanced cabling in accordance with the reference implementations of EN 50173 series using currents per conductor of up to 500 mA; - 1-pair balanced cabling using currents per conductor of up to 2 000 mA; and targets the support of applications that provide remote power over balanced cabling to terminal equipment,  b) covers the transmission and electrical parameters needed to support remote power over balanced cabling, c) covers various installation scenarios and how these may impact the capability of balanced cabling to support remote powering, d) specifies design and configuration of cabling as specified in EN 50173-1. NOTE SELV requirements specify a maximum voltage of 60 V DC and LPS is understood in the applications referenced to be up to 100 W supplied within cabling. This document includes a mathematical model to predict the behaviour of different bundle sizes, various cabling constructions, and installation conditions for different current capacities.

This document is applicable to electrical insulating matting made of flexible insulating material for use as a covering of the surface on which the worker is positioned and for worker´s electrical protection on electrical installations up to 36 000 V AC for AC use or 36 000 V AC and 54 000 V DC for AC/DC use.
NOTE 1 The electric potential of the surface on which the worker is positioned is usually that of earth.
NOTE 2 See 4.2 for maximum use voltage.
NOTE 3 DC only rated matting is not specified in this document.
NOTE 4 This document does not cover the use of insulating blankets (see IEC 61112)

This part of IEC 61000 defines test methods for immunity to voltage dips, short interruptions and voltage variations at the DC input power port of electrical or electronic equipment.
This document is applicable to equipment and systems whose DC input power ports are intended to be connected to low voltage DC networks external to the equipment and systems.
The object of this document is to establish a common and reproducible basis for testing electrical and electronic equipment when subjected to voltage dips, short interruptions or
voltage variations on DC input power ports.
This document defines:
– the range of test levels;
– the test generator;
– the test set-up;
– the test procedure.
The test described hereinafter applies to electrical and electronic equipment and systems. It also applies to modules or subsystems whenever the equipment under test’s (EUT) rated power is greater than the test generator capacity specified in Clause 6.
The ripple at the DC input power port is not included in the scope of this document. It is covered by IEC 61000-4-17.
This document does not specify the tests to be applied to particular apparatus or systems. Its main aim is to give a general basic reference to IEC product committees. These product committees (or users and manufacturers of equipment) remain responsible for the appropriate choice of the tests and the severity level to be applied to their equipment.

COMMENT The text of this clause may repeat information already given in some fields of the above title block. Essential information on the special type of components covered by the drafted detail specification may be added, preferably at the place marked with "…".
This detail specification specifies the characteristics and ratings of surface mount (SMD) film resistors for use in electronic equipment, which are typically assembled on the surface of circuit boards.
...
The resistors covered herein are classified to level G, as defined in IEC 60115-1:2020, 3.4 for general electronic equipment, typically operated under benign or moderate environmental conditions, where the major requirement is function. Examples for level G include consumer products and telecommunication user terminals.
This detail specification is based upon the blank detail specification IEC 60115-8-10:2026.
This detail specification establishes test schedules and performance requirements permitting the quality assessment of the resistors covered herein according to the quality assessment procedures prescribed by IEC 60115-1:2020, Annex Q.

This European Standard specifies methods for measuring the performance of electric storage water
heaters for the production of sanitary hot water for household and similar use.
The object is to state and define the principal performance characteristics of electric storage water
heaters and to describe the test methods for measuring these characteristics.
NOTE 1 This standard does not apply to;
− storage water heaters that use electricity as a secondary source of heating the water;
− storage water heaters that do not use a tank to store hot water;
− electric storage water heaters that do not meet the minimum (or maximum) output performance of the smallest (or biggest)
load profile, as defined in Table 4.
NOTE 2 This standard does not specify performance or safety requirements. For safety requirements see EN 60335-1:2020 in
conjunction with EN 60335-2-21:2023

This document specifies procedures for static and cyclic strength tests on lower-limb prostheses (see NOTE 2) which typically produce compound loadings by the application of a single test force. The compound loads in the test sample relate to the peak values of the components of loading which normally occur at different instants during the stance phase of walking. This document specifies Test Ranges (R) by specifying locomotion profiles for the cyclic test in relation to the intended use. According to the concept of the tests of this document, each sample of lower limb prosthetic device or structure submitted for test is, nevertheless, free to develop its individual performance under load. The tests described in this document comprise: principal static and cyclic tests for all components; a separate static test in torsion for all components; separate static and cyclic tests on ankle-foot devices and foot units for all ankle-foot devices as single components including ankle units or ankle attachments and all foot units as single components; a separate static ultimate strength test in maximum knee flexion on knee joints and associated parts for all knee units or knee-shin-assemblies and adjacent components that normally provide the flexion stop on a complete prosthesis; optional separate tests on knee locks for all mechanisms which lock the knee joint in the extended position of the knee unit or knee-shin-assembly. The tests described in this document apply to specific types of ankle-disarticulation prostheses (see NOTE 2), to transtibial (below-knee), knee-disarticulation and transfemoral (above-knee) prostheses and to the distal (lower) part of hip-disarticulation and hemi-pelvectomy prostheses (see NOTE 3). The test geometry described in this standard is only intended to be used up to a level of 150 mm above the knee-joint centre. This document is suitable for the assessment of the conformity of lower limb prosthetic devices or structures with the strength requirements specified in ISO 22523:2006, 4.4 (see NOTE 1). Lower limb prosthetic devices or structures on the market, which have demonstrated their compliance with the strength requirements specified in ISO 22523:2006, 4.4 through submission to the relevant tests of ISO 22523:2006, need not be retested to this document. NOTE 1 The tests can be performed on complete structures, on part structures or on individual components. NOTE 2 The tests only apply to ankle-disarticulation prostheses which include (foot) components of prosthetic ankle-foot devices taken from the normal production line. NOTE 3 The distal part comprises the knee unit, the ankle-foot device and all parts between. Tests on hip units are described in ISO 15032.

This document gives guidance on the sample preparation of milk and milk products for physical and chemical analysis, including analysis by applying instrumental methods. This document specifies the (sub)sampling and sample preparation steps carried out after sampling in accordance with ISO 707 | IDF 50 [1] and prior to method-specific sample preparations (e.g. as with analytical methods). NOTE Analysis on volatile substances, minor components or allergens can require additional precautionary measures in sample preparation in order to avoid loss of or contamination with one or more target analytes.

This document provides considerations on the planning and execution of verification and validation (V&V) of the cybersecurity of items and components of road vehicles, in the context of ISO/SAE 21434.

This document specifies additional competence requirements for personnel involved in the audit and certification process for innovation management systems (IMS) and complements the existing requirements of ISO/IEC 17021-1. NOTE This document is applicable to auditing and certification of an IMS based on ISO 56001.

This document specifies the acceptable quantitative and qualitative microbiological limits in finished cosmetic products. It is applicable to all cosmetics, and assists interested parties in the assessment of the microbiological quality of cosmetic products.

This document specifies a method to determine the moisture content of aluminium ores. It applies to the samples taken from bulk aluminium ores, e.g. shipments and stockpiles.

This method is applicable to a concentration range of 52,80 % mass fraction to 86,40 % mass fraction of the metallic Fe.

IEC 60127-4:2026 relates to universal modular fuse-links (UMF) for printed circuits and other substrate systems, used for the protection of electric appliances, electronic equipment, and component parts thereof, normally intended to be used indoors. It does not apply to fuse-links for appliances intended to be used under special conditions, such as in a corrosive or explosive atmosphere. These fuses are normally intended to be mounted or replaced only by appropriately skilled persons using specialized equipment. This document applies in addition to the requirements of IEC 60127-1. The objectives of this part of IEC 60127 are as given in IEC 60127-1, with the additional requirement of a degree of non-interchangeability. This fourth edition cancels and replaces the third edition published in 2005, Amendment 1:2008 and Amendment 2:2012. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) align to IEC 60127-1:2023, third edition;
b) enhance the rated current of UMFs to 100A and provide the corresponding maximum voltage drop and maximum sustained dissipation;
c) modify the figures;
d) update the normative references to the latest version.
This International Standard is to be used in conjunction with IEC 60127-1:2023

This document provides an environment test to determine the ability of smart textiles (e.g. electrically heated garment) to withstand rapid changes of ambient temperature. This document is applicable to jacket, vest, jumper, etc., which includes the electrically operating part.

This part of IEC 60695 summarises the test methods that are used in the assessment of the corrosivity of fire effluent. It presents a brief summary of test methods in common use, either as international standards, national or industry standards. It includes special observations on their relevance, for electrotechnical products and their materials, to real fire scenarios and gives recommendations on their use.

This document specifies: the classification and selection criteria applicable to refrigerating systems; safety requirements for the installation site of refrigerating systems and their ancillary components. These classification and selection criteria are used in ISO 5149-2 and ISO 5149-4. This document is applicable to: refrigerating systems, stationary or mobile, of all sizes, except vehicle air conditioning systems covered by a specific product standard, e.g. ISO 13043 and SAE J 639; secondary cooling or heating systems; the location of the refrigerating systems; parts replaced and components added after publication of this document if they are not identical in function and in capacity. This document is applicable: to new refrigerating systems, extensions or modifications of already existing systems; for used systems, being transferred to and operated on another site; in the case of the conversion of a system for another refrigerant. This document is only applicable to systems containing refrigerants which have a safety group classification and are listed in ISO 817.

This document defines terms used in the specification, design, manufacture, construction, installation, commissioning, maintenance and decommissioning of refrigerating systems with regard to safety and environmental requirements. The term "refrigerating systems" includes heat pumps and air conditioners.

This document specifies the design, construction and installation of refrigerating systems, including piping, components, materials and ancillary equipment directly associated with such systems, which are not covered in ISO 5149-1, ISO 5149-3, or ISO 5149-4. It also specifies requirements for testing, commissioning, marking and documentation. Requirements for secondary heat-transfer circuits are excluded except for any safety devices associated with the refrigerating system. This document is applicable to new refrigerating systems, extensions or modifications of already existing systems, and for used systems, being transferred to and operated on another site. This document is applicable to: refrigerating systems, stationary or mobile, of all sizes, except vehicle air conditioning systems covered by a specific product standard; NOTE Example of specific product standard is ISO 13043 and SAE J 639. secondary cooling or heating systems; the location of the refrigerating systems; replaced parts and added components after the adoption of this document, if they are not identical in function and in capacity; the conversion of a system for another refrigerant. This document does not apply to goods in storage, with respect to spoilage or contamination.

NOTE Throughout this standard, the abbreviation ACS (ASSEMBLY for construction site, see 3.1.101) is used for a low-voltage switchgear and controlgear assembly intended for use on construction and similar sites.
This part of 61439 defines the specific requirements of ACS as follows:
- ASSEMBLIES for which the rated voltage does not exceed 1 000 V in case of AC or 1 500 V in case of DC;
- ASSEMBLIES where the nominal primary voltage and the nominal secondary voltage of transformers incorporated in ACS are within the limits specified above;
- ASSEMBLIES intended for use on construction sites, both indoors and outdoors, i.e. temporary places of work to which the public do not generally have access and where building construction, installation, repairs, alteration or demolition of property (buildings) or civil engineering (public works) or excavation or any other similar operations are carried out;
- transportable (semi-fixed) or mobile ASSEMBLIES with enclosure.
The manufacture and/or assembly may be carried out other than by the original manufacturer.
This standard does not apply to individual devices and self-contained components, such as motor starters, fuse switches, electronic equipment, etc. which will comply with the relevant product standards.
This standard does not apply to ASSEMBLIES for use in the administrative centres of construction sites (offices, cloakrooms, ASSEMBLY rooms, canteens, restaurants, dormitories, toilets, etc.).
Requirements for electrical protection provided by equipment manufactured according to this International Standard are given in IEC 60364-7-704.

This document gives regional requirements for Australia, Canada, China, Japan, South Africa and the United States of America, which are outside the United Kingdom and the European Economic Area (EEA), for the types of industrial trucks specified in the scopes of ISO 3691-1, ISO 3691-2, ISO 3691-3, ISO 3691-4 and ISO 3691-6. It is intended to be used in conjunction with ISO 3691-1, ISO 3691-2, ISO 3691-3, ISO 3691-4 and ISO 3691-6.

This document specifies safety requirements and the corresponding test methods for reclined cradles intended for children from birth up to when they start to stand up and infant swings intended for children from birth up to when they start to try to sit up.
This document is also applicable to car seats complying with UN R44 or UN R129 that can be used as type A or type B reclined cradles and/or infant swings according to the instructions for use. If usage as a type A or type B reclined cradle and/or an infant swing is not included in the product information or marketing material, car seats are excluded from the scope of this document.
This document does not apply to reclined cradles or infant swings designed for children with special needs, and/or which fall under the scope of Regulation (EU) 2017/745 (medical devices).
If a reclined cradle or infant swing has several functions or can be converted into another function, the relevant European Standards apply.
Swings falling under the scope of EN 71-8 are excluded from the scope of this document.
NOTE   For the rest of the document, the word “product” will be used when referring at the same time to reclined cradles and infant swings.

This document specifies general safety requirements for self-loading mobile concrete mixers (here-after referred to as "SLMs") as defined in ISO 18650-1:2021, with rigid or articulated wheeled chassis.
This document applies to SLMs which are designed for front or rear loading and can be provided with a slewing and/or tilting frame where the rotating drum and the self-loading equipment (lift arms and bucket) are mounted on. SLMs can also be fitted with accessories such as water dosing means and a weighing system.
This document is not applicable to the following:
-   machines designed primarily for earth moving, such as loaders or dumpers (see applicable parts of the EN 474 series);
-   truck mixers (see EN 12609).
This document deals with all significant hazards, hazardous situations and events relevant to SLMs, whether used as intended and under conditions foreseen or under conditions of misuse reasonably foreseeable by the manufacturer (see Annex A).
This document does not provide performance levels required for safety related functions of control systems.
NOTE   A document providing detailed description of safety functions for SLMs and related performance levels required is under development.
This document does not address hazards that can occur:
-   during manufacture;
-   when using SLMs on public roads, where specific local road regulations can apply;
-   when operating in potentially explosive atmospheres.
This document does not address hazards specifically related to:
-   SLMs designed to operate with varying levels of autonomy or when SLMs have embedded safety-systems with fully or partially self-evolving behaviour or logic using machine learning approaches, including collaborative applications;
-   SLMs when intended to be connected to the internet or to an external network or device that communicates with it (protection against corruption).
This document is not applicable to SLMs manufactured before the date of its publication.

This document specifies the fundamental principles and concepts of conformity assessment schemes (programmes) and provides guidelines for understanding, developing, operating or maintaining them.

This document specifies a test method for determining the ability of smart textile systems to withstand high pressure conditions in underwater applications.

This document provides an overview of the standards developed in the ISO 25500 series for supply chain interoperability and integration. This document: states the subject matter of the ISO 25500 series as a whole; establishes the principles of supply chain interoperability and integration; describes the path to supply chain interoperability and integration; describes the structure of the supply chain interoperability and integration series; establishes the relationship of the supply chain interoperability and integration series with other International Standards. The following is outside the scope of this document: the interoperability and integration of the physical objects or services exchanged.