SIST - Slovenian Institute for Standardization

This document specifies a method for the determination of selected polybrominated diphenylethers (PBDE) (see Figure 1 and Table 1) in sediment, suspended particulate matter and biota using gas chromatography coupled with tandem mass spectrometry (GC-MS/MS) or with high resolution mass spectrometry (GC-HRMS) in the electron impact (EI), negative ion chemical ionization (NCI) or atmospheric pressure ionization (APCI) mode.
The method is applicable to sediment and suspended particulate matter samples with limits of quantification of 0,2 µg/kg dry mass (dm) for brominated diphenylether (BDE) BDE-28 to BDE-183, of 2 µg/kg dry mass (dm) for BDE‑209.
The method is applicable as well with lower limits of quantification (LOQ), if specific clean-up methods, described in Clause 10, Table 3, method 1 and method 2 in combination with measurement methods GC-MS/MS or GC-HRMS after electron impact ionization (El) or negative ion chemical ionization (NCI) for BDE-209 are used. Depending on the analytical capability of the instrument, limits of quantification down to 0,003 µg/kg dm for BDE-28 to BDE-154 and 0,02 µg/kg dm for BDE-183 and 1 µg/kg dm for BDE-209 and lower are possible.
The method is applicable to biota samples with limits of quantification down to 0,000 2 µg/kg fresh mass (fm) (BDE-28 to BDE-154) and 0,03 μg/kg fresh mass (fm) (BDE-183), if specific clean-up methods, described in Table 4 in combination with measurement methods GC-MS/MS or GC-HRMS after electron impact ionization (El) are used.
Performance data are listed in Annex E.

This document specifies general methods, with suitable test conditions, for the determination of the ash of a range of plastics. The particular conditions chosen can be included in the specifications for the plastic material in question.
Particular conditions applicable to poly(alkylene terephthalate) materials, unplasticized cellulose acetate, polyamides and poly(vinyl chloride) plastics, including some specific filled, glass-fibre-reinforced and flame-retarded materials, are specified in ISO 3451-2, ISO 3451-3, ISO 3451-4 and ISO 3451-5.

This document specifies the requirements for seal-less rotodynamic pumps that are driven with permanent magnet coupling (magnet drive pumps) or with canned motor, and which are mainly used in chemical processes, water treatment and petrochemical industries. Their use can be dictated by space, noise, environment or safety regulations.
Seal-less pumps are pumps where an inner rotor is completely contained in a pressure vessel holding the pumped fluid. The pressure vessel or primary containment device is sealed by static seals such as gaskets or O-rings.
Pumps normally conform to recognized standard specifications (e.g. ISO 5199, explosion protection, electromagnetic compatibility), except where special requirements are specified herein.
This document includes design features concerned with installation, maintenance and operational safety of the pumps, and defines those items to be agreed upon between the purchaser and manufacturer/supplier.
Where conformity to this document has been requested and calls for a specific design feature, alternative designs can be offered providing that they satisfy the intent of this document and they are described in detail. Pumps which do not conform with all requirements of this document can also be offered providing that the deviations are fully identified and described.
Whenever documents include contradictory requirements, they are applied in the following sequence of priority:
purchase order (or inquiry, if no order placed), see Annexes C and D;
data sheet (see Annex A) or technical sheet or specification;
this document;
other standards.

This part of IEC/IEEE 62582 contains methods for condition monitoring of organic and polymeric materials in instrumentation and control systems using tensile elongation techniques in the detail necessary to produce accurate and reproducible measurements. This document includes the requirements for selection of samples, the measurement system and conditions, and the reporting of the measurement results.
The different parts of IEC/IEEE 62582 are measurement standards, primarily for use in the management of ageing in initial qualification and after installation. IEC/IEEE 62582-1 includes requirements for the application of the other parts of IEC/IEEE 62582 and some elements which are common to all methods. Information on the role of condition monitoring in qualification of equipment important to safety is found in IEC/IEEE 60780-323.
This document is applicable to non-energised equipment.

This part of IEC/IEEE 62582 contains methods for condition monitoring of organic and polymeric materials in instrumentation and control systems using the indenter measurement technique in the detail necessary to produce accurate and reproducible measurements. It includes the requirements for the selection of samples, the measurement system and measurement conditions, and the reporting of the measurement results.
The different parts of IEC/IEEE 62582 are measurement standards, primarily for use in the management of ageing in initial qualification and after installation. IEC/IEEE 62582-1 includes requirements for the application of the other parts of the IEC/IEEE 62582 series and some elements which are common to all methods. Information on the role of condition monitoring in the qualification of equipment important to safety is found in IEC/IEEE 60780-323.
This document is intended for application to non-energised equipment.

This document specifies a method for the measurement of flame spread times of vertically oriented textile fabrics and industrial products in the form of single or multi-component textile fabrics (coated, quilted, multilayered, sandwich combinations, and similar combinations) when subjected to a small, defined flame.

This document specifies methods for the measurement of the thermal resistance and water-vapour resistance , under steady-state conditions, of e.g. fabrics, films, coatings, foams and leather, including multilayer assemblies, for use in clothing, quilts, sleeping bags, upholstery and similar textile or textile-like products.
The application of this measurement technique is restricted to a maximum thermal resistance and water-vapour resistance which depend on the dimensions and construction of the apparatus used (e.g. 2 m2·K/W and 700 m2·Pa/W respectively, for the minimum specifications of the equipment referred to in this document).
The test conditions used in this document are not intended to represent specific comfort situations, and performance specifications in relation to physiological comfort are not stated.

IEC 61753-022-13:2026 defines the minimum initial test and measurement requirements, and severities which multimode fibre optic connectors terminated as a pigtail or a patchcord satisfy in order to be categorized as meeting the IEC standard category OP+HP (Extended outdoor protected environment with additional heat dissipation), as defined in IEC 61753-1.
If tests are performed on the connectors terminated as pigtails or patchcords for category OP+HP, and the product pass, the product will be automatically qualified or categorized as meeting the IEC standard for categories OP+, OP, OPHD, C and CHD.

This document specifies a method for exposing plastics to concentrated solar radiation using reflecting concentrators to accelerate the weathering processes. The purpose is to assess property changes produced after specified stages of such exposures. The reflecting concentrators used in these exposures are sometimes referred to as “Fresnel reflectors” because, in cross-section, the array of mirrors used to concentrate the solar radiation resembles the cross-section of a Fresnel lens.
General guidance concerning the scope of the ISO 877 series is given in ISO 877-1.
NOTE            Additional information about solar concentrating exposures, including a partial list of standards in which they are specified, is given in the Bibliography.

This document specifies the calibration and adjustment of the metrological characteristics of contact (stylus) instruments for the measurement of surface texture by the profile method as defined in ISO 25178-601. The calibration and adjustment specified within this document is intended to be carried out with the aid of measurement standards.
NOTE            Annex B specifies the calibration and adjustment of metrological characteristics of simplified operator contact (stylus) instruments which do not conform with ISO 25178-601.

This document specifies safety requirements and test methods for changing units, changing pads and changing unit accessories for domestic use.
This document only covers the function of the item as a changing unit. If the item can be converted or used for another function (e.g. cots, storage furniture, bath tubs and stands, etc.), other relevant European Standards apply.
The changing unit can be foldable and can be fitted with a child bathtub or other additional items.

This document provides the information needed to assess the condition over time of a unionid population, and the level of information for assessing whether a plan or project may be detrimental to their future prospects. It provides guidance on methods for survey and monitoring unionid mussel populations and the environmental characteristics important for maintaining populations in favourable condition. The document is based on best practice developed and used by unionid mussel experts in Europe, and describes approaches that individual countries have adopted for survey, data analysis and condition assessment.
Standard methods for restoring populations are not within the scope of this document.

This document specifies a method for the determination of the puncture resistance by measuring the force required to push a flat-ended plunger through geosynthetics.
The test is normally carried out on dry specimens conditioned in the specified atmosphere.
The test is applicable to most types of geosynthetic products, but does not apply to products with apertures greater than 10 mm.

This document specifies requirements and test methods for activity toys.
This document also specifies requirements for:
-   separately sold accessories for, and components of activity toys;
-   separately sold swing elements that are ready for use on or in combination with an activity toy;
-   construction packages for activity toys including components used to build activity toys in accordance with a scheduled building instruction.
The scope of this document excludes:
-   playground equipment intended for public use dealt with in the EN 1176 series;
-   bow-mounted rocking activity toys such as rocking horses and similar toys, which are covered by specific requirements in EN 71-1;
-   toy pools with maximum depth of water over 400 mm measured, between the overflow level and the deepest point within the pool;
NOTE 1   For information regarding the classification of pools as toys see European Commission guidance document No. 8 on the application of the Directive 2009/48/EC on the safety of toys - Pools [1].
-   pools with maximum depth of water over 400 mm measured, between the overflow level and the deepest point within the pool, without play elements covered e.g. by the EN 16582 series or EN 16927.
NOTE 2   There is an enhanced risk of drowning in pools where the depth of water is in excess of 400 mm.
-   toy slides designed to be used in conjunction with domestic in-ground swimming pools;
-   trampolines for domestic use dealt with in EN 71-14;
-   powered blowers used to continuously inflate inflatable activity toys.
NOTE 3   Powered blowers used to continuously inflate inflatable activity toys are considered to be a household appliance and covered by requirements given in EN 60335-2-80.
See also Clause A.1.

This document specifies the characteristics of grooved pins with half-length centre oval grooves (with closed ends), in steel and stainless steel, and with nominal diameter 1 mm to 25 mm.
These grooved pins are designed to fulfil the main following functions:
relative rotation of the assembled parts, and
positioning or guiding,
with an easy installation (due to its symmetrical shape) and a high level of pull-out resistance (due to the elastic fit behaviour of the pin).
The general requirements (including functional principles for grooved pins and assembly) are specified in ISO 13669.

This document establishes a classification for phenolic and aminoplastic polycondensation adhesives according to their suitability for use for load-bearing timber products in defined climatic exposure conditions, and specifies performance requirements for such adhesives for the factory manufacture or factory-like manufacturing conditions of load-bearing timber products only.
This document only specifies the performance of an adhesive for use in an environment corresponding to the defined conditions.
The performance requirements of this document are applicable to the adhesive only, not to the manufacturing timber products. This document does not cover the performance of adhesives for on-site gluing (except for factory-like conditions) or the production of wood-based panels, except solid wood panels, or modified and stabilized wood with considerably reduced swelling and shrinkage properties, e.g. acetylated wood, heat treated wood and polymer impregnated wood.
This document is primarily intended for use by adhesive manufacturers and for use in timber products bonded with adhesives, to assess or control the quality of adhesives. The requirements are applicable to the type testing of the adhesives. Production control activities are outside the scope of this document.
Adhesives meeting the requirements of this document are adequate for use in load-bearing timber products, provided that the bonding process has been carried out according to an appropriate product standard.

This document establishes a classification for one component polyurethane (PUR) adhesives according to their suitability for use in load-bearing timber products in defined climatic exposure conditions, and specifies performance requirements for such adhesives for the factory manufacture or factory-like manufacturing of load-bearing timber products only.
It also classifies “adhesive product lines” where all the products within the line have the same chemical composition except for a different amount of catalyst.
This document only specifies the performance of adhesives for use in an environment corresponding to the defined conditions.
The performance requirements of this document are applicable to the adhesives only, not to the manufactured timber products. This document does not cover the performance of adhesives for on-site gluing (except for factory-like conditions) or the production of wood-based panels, except solid wood panels, or modified and stabilized wood with considerably reduced swelling and shrinkage properties, e.g. acetylated wood, heat treated wood and polymer impregnated wood.
This document is primarily intended for use by adhesive manufacturers and for use in timber products bonded with adhesives, to assess or control the quality of adhesives. The requirements are applicable to the type testing of the adhesives. Production control activities are outside the scope of this document.
Adhesives meeting the requirements of this document are adequate for use in load-bearing timber products, provided that the bonding process has been carried out according to an appropriate product standard.
This document does not address the classification and use of adhesives in combination with the spraying of water before or during the bonding process; see informative Annex C of this document.
This does neither allow nor forbid the use of adhesives in combination with the spraying of water.

This document is directly applicable to pulsed X-radiation with pulse duration of 0,1 ms up to 10 s. This range covers the whole range used in medical diagnostics at the time of publication. Some specifications can also be applicable for much shorter pulses; one example is the air kerma of one pulse. Such a pulse can be produced, e.g. by X-ray flash units or high-intensity femtosecond-lasers. Other specifications are not applicable for much shorter pulses; one example is the time-dependent behaviour of the air kerma rate. This cannot be measurable for technical reasons as no suitable instrument is available, e.g. for pulses produced by a femtosecond-laser.
This document specifies the characteristics of reference pulsed radiation for calibrating and testing radiation protection dosemeters and dose rate meters with respect to their response to pulsed radiation. At this point, it is only concerned with the characteristics of single pulses. Single pulses are the most difficult for dosemeters to measure. Determining the dose for repeated pulses is easier, but still more difficult than for continuous radiation, i.e. the performance of the dosemeters when measuring repeated pulses lies between these extremes. The radiation characteristics includes the following:
time-dependent behaviour of the air kerma rate of the pulse;
time-dependent behaviour of the X-ray tube high voltage during the pulse;
uniformity of the air kerma rate within a cross-sectional area of the radiation beam;
air kerma of one radiation pulse;
air kerma rate of the radiation pulse;
repetition frequency.
This document does not define new radiation qualities but uses those radiation qualities specified in existing ISO and IEC standards. Instead, this document gives the link between the parameters for pulsed radiation and the parameters for continuous radiation specifying the radiation qualities. It does not specify specific values or series of values for the pulsed radiation field but specifies only those limits for the relevant pulsed radiation parameters that are required for calibrating dosemeters and dose rate meters and for determining their response depending on the said parameters.
The pulse parameters with respect to the phantom-related quantities were determined using conversion coefficients according to ISO 4037 (all parts). This is possible as the radiation qualities specified in existing ISO and IEC standards are used.
A given reference pulsed X-ray facility is characterized by the parameter ranges over which the full specifications and requirements according to this document are met. Therefore, not all reference pulsed X-ray facilities can produce pulses covering the same parameter ranges.

IEC 62705:2022 gives requirements for the lifecycle management of radiation monitoring systems (RMS) and gives guidance on the application of existing IEC standards covering the design and qualification of systems and equipment. The purpose of this document is to lay down requirements for the lifecycle management of RMSs and give application guidance. This document is intended to be consistent with the latest versions of International Standards dealing with radiation monitors, sampling of radioactive materials, instruments calibration, hardware and software design, classification, and qualification. This document is applicable to RMSs installed in nuclear facilities intended for use during normal operation, anticipated operational occurrences (AOO), design basis accidents (DBA) and design extension conditions (DEC), including severe accidents (SA). This second edition cancels and replaces the first edition published in 2014. This edition includes the following significant technical changes with respect to the previous edition:
- modification of the title.
- to be consistent with the categorization of the accident condition.
- to update the references to new standards published since the first edition.
- to update the terms and definitions.

This document specifies a range of fineness of precious metal alloys recommended for use in the field of jewellery.
NOTE            There is a possibility that national legal requirements for the designation, marking and stamping of finished articles exist in the respective countries.

This part of the IEC/IEEE 62582 series contains requirements for application of the other parts of IEC/IEEE 62582 related to specific methods for condition monitoring in electrical equipment important to safety of nuclear power plants. It also includes requirements which are common to all methods. The procedures defined in IEC/IEEE 62582 are intended for detailed condition monitoring.
IEC/IEEE 62582 specifies condition monitoring methods in sufficient detail to enhance the accuracy and repeatability, and provide standard formats for reporting the results. The methods specified are applicable to electrical equipment containing polymeric materials. Some methods are especially designed for the measurement of condition of a limited range of equipment whilst others can be applied to all types of equipment for which the polymeric parts are accessible.
Although the scope of IEC/IEEE 62582 is limited to the application of instrumentation and control systems important to safety, the condition monitoring methods can also be applicable to other components which include polymeric materials.
The different parts of IEC/IEEE 62582 are measurement standards, primarily for use in the management of ageing in initial qualification and after installation. For the technical background of condition monitoring methods, reference is made to other IEC standards, e.g. IEC 60544-5 [1]. Information on the role of condition monitoring in qualification of electrical equipment important to safety is found in IEC/IEEE 60780-323. General information on management of ageing can be found in IEC 62342 [5] and IEEE 1205 [6].
NOTE A simplified version of the procedures can be appropriate for preliminary assessment of the need for detailed measurements.

This document specifies requirements and methods of tests for mechanical and physical properties of toys.
This document applies to toys for children, toys being any product or material designed or intended, whether or not exclusively, for use in play by children of less than 14 years. It refers to new toys taking into account the period of foreseeable and normal use, and that the toys are used as intended or in a foreseeable way, bearing in mind the behaviour of children.
It includes specific requirements for toys intended for children under 36 months, children under 18 months and for children who are too young to sit up unaided. For example, soft-filled toys with simple features intended for holding and cuddling are considered as intended for use by children under 36 months.
NOTE Information relating to the age grading and age determination of toys can be found in CEN ISO/TR 8124-8 [22] and the European Commission’s Guidance Documents on the Toy Safety Directive.
This document also specifies requirements for packaging, marking and labelling.
This document does not apply to the following toys:
— automatic playing machines, whether coin operated or not, intended for public use;
— toy vehicles equipped with combustion engines;
— toy steam engines;
— toy slings and toy catapults, supplied without projectiles;
— remote control flying toys incorporating rotor blade(s) which are capable of spinning approximately horizontally, each blade being greater than 175 mm in length, measured from the centre of rotation to the blade tip, and with an overall mass of the flying toy greater than 50 g.
This document does not cover musical instruments, sports equipment or similar items but does include their toy counterparts.
Toy slings and toy catapults supplied with projectiles are covered by this document.
This document does not cover electrical safety aspects of toys which are covered by EN IEC 62115.
Furthermore, it does not cover the following items which, for the purpose of this document, are not considered as toys:
a) decorative objects for festivities and celebrations;
b) products for collectors, provided that the product or its packaging bears a visible and legible indication that it is intended for collectors of 14 years of age and above; examples of this category are:
1) detailed and faithful scale models (see A.2),
2) kits for the assembly of detailed scale models,
3) folk dolls and decorative dolls and other similar articles,
4) historical replicas of toys,
5) reproductions of real fire arms;
c) sports equipment including roller skates, inline skates, and skateboards intended for children with a body mass of more than 20 kg;
d) bicycles with a maximum saddle height of more than 435 mm, measured as the vertical distance from the ground to the top of the seat surface, with the seat in a horizontal position and with the seat pillar set to the minimum insertion mark;
e) scooters and other means of transport designed for sport, or which are intended to be used for travel on public roads or public pathways;
f) electrically-driven vehicles which are intended to be used for travel on public roads, public pathways, or the pavement thereof;
g) aquatic equipment intended to be used in deep water, and swimming learning devices for children, such as swim seats and swimming aids;
h) puzzles with more than 500 pieces;
i) guns and pistols using compressed gas, with the exception of water guns and water pistols;
j) bows for archery over 120 cm long;
k) fireworks, including percussion caps which are not specifically designed for toys;
l) products and games using sharp-pointed missiles, such as sets of darts with metallic points;
m) functional educational products, such as electric ovens, irons or other functional products, as defined in EU Directive 2009/48/EC (Toy Safety Directive) [21], operated at a nominal voltage exceeding 24 V which are sold exclusively for teaching purposes under adult supervision;
n) products i

This document specifies the characteristics of corklinoleum, supplied in roll form.
To encourage the consumer to make an informed choice, this document includes a classification system based on intensity of use, which shows where resilient floor coverings should give satisfactory service (see EN ISO 10874). It also includes requirements for marking.
The term 'linoleum' is frequently incorrectly applied to a range of floor coverings, often to those based on polyvinyl chloride or rubber. This document does not apply to such.

This document specifies requirements and guidelines for assessing the chemical airborne cleanliness of equipment and materials which are foreseen to be used in cleanrooms and associated controlled environments that are linked to the ISO standard for air cleanliness by chemical concentration (see ISO 14644-8).
This document does not apply to the following:
health and safety requirements;
compatibility with cleaning agents and techniques;
cleanability;
biocontamination;
specific requirements of equipment and materials for processes and products;
design details of equipment.

IEC 62397:2022 describes the requirements for resistance temperature detectors (RTDs) suitable for applications in I&C systems important to safety of nuclear power plants. The requirements of RTDs include design, materials, manufacturing, testing, calibration, procurement, and inspection. RTDs used for safety applications in Nuclear Power Plants can be categorized into direct-immersed and thermowell-mounted RTDs.
This standard describes the requirements for the design, material selection, procurement, construction, and testing of resistance temperature detectors (RTDs) used in nuclear power plants (NPPs). These RTDs may be used in both the nuclear safety I&C systems and/or in the non-safety-related instrumentation systems.
This second edition cancels and replaces the first edition, published in 2007; it also cancels and replaces the first edition of IEC 61224:1993. This edition includes the following significant technical changes with respect to the previous edition.

This part of IEC/IEEE 62582 specifies methods for condition monitoring of organic and polymeric materials in instrumentation and control systems using oxidation induction techniques in the detail necessary to produce accurate and reproducible measurements. It includes the requirements for sample preparation, the measurement system and conditions, and the reporting of the measurement results.
The different parts of IEC/IEEE 62582 are measurement standards, primarily for use in the management of ageing in initial qualification and after installation. IEC/IEEE 62582-1 includes requirements for the application of the other parts of the IEC/IEEE 62582 series and some elements which are common to all methods. Information on the role of condition monitoring in the qualification of equipment important to safety is found in IEC/IEEE 60780-323.

This document specifies a method for the measurement of ease of ignition of vertically oriented textile fabrics and industrial products in the form of single or multi-component textile fabrics (coated, quilted, multilayered, sandwich constructions, and similar combinations), when subjected to a small, defined flame.

This document establishes an Artificial Intelligence (AI) and Machine Learning (ML) framework for describing a generic AI system using ML technology. The framework describes the system components and their functions in the AI ecosystem. This document is applicable to all types and sizes of organizations, including public and private companies, government entities, and not-for-profit organizations, that are implementing or using AI systems.

This document specifies a method of determining the ability of adhesive bonds to resist static load. It is applicable to adhesives used in load bearing timber structures.
It is applicable for the following applications:
a) for assessing the compliance of adhesives according to EN 301, EN 15425, EN 16254, EN 17334 and EN 17418;
b) for assessing the suitability and quality of adhesives for load-bearing timber structures;
c) for assessing the effect on the bond strength resulting from constant load at different climate conditions.
This method is intended primarily to obtain performance data for the classification of adhesives for load bearing timber structures according to their suitability for use in defined climatic environments.
This method is not intended to provide data for structural design and does not necessarily represent the performance of the bonded member in service.

This document provides packages of security assurance and security functional requirements that are intended to be useful in support of common usage by stakeholders.
The users of this document can include consumers, developers and evaluators of secure IT products.

This document specifies a method for the determination of the softening point of bitumens and bituminous binders in the range of 28 °C to 150 °C.
The method described is also applicable to bituminous binders that have been recovered from bituminous mixes, e.g. by extraction according to EN 12697-3 [1].
WARNING — The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

This document establishes terminology for AI and describes concepts in the field of AI.
This document can be used in the development of other standards and in support of communications among diverse, interested parties or stakeholders.
This document is applicable to all types of organizations (e.g. commercial enterprises, government agencies, not-for-profit organizations).

The present document establishes a broadcasting standard for the Digital Audio Broadcasting (DAB) system designed for delivery of high-quality digital audio and video programmes and data services for mobile, portable and fixed reception from terrestrial transmitters in the Very High Frequency (VHF) frequency bands as well as for distribution through cable networks. The DAB system is designed to provide spectrum and power efficient techniques in terrestrial transmitter network planning, known as the Single Frequency Network (SFN) and the gap-filling technique. The DAB system meets the required sharing criteria with other radiocommunication services. The present document defines the DAB transmission signal. It includes the coding algorithms for multiplexing of audio and video programmes and data services, channel coding and modulation. Provision is also made for transmission of additional data services which may be programme related or not, within the limit of the total system capacity. The present document provides information on the system configuration which includes information about the ensembles, services, service components and linking of them. The present document describes the nominal characteristics of the emitted DAB signal. The aspects related to the receiver design are outside the scope of the present document.

This standard specifies the dimensions and characteristics of the interfaces, requirements, test methods and marking of ski mountaineering boots and clip-on binding crampons which are fixed together with attachment at the boot toe and boot heel, the proper fixed function of which depends on the dimensions and design of the interfaces.

This document applies to manual braking devices with partially assisted locking used in mountaineering, climbing and related activities for belaying, to protect against falls from a height and/or for abseiling with speed regulation. These are for use with mountaineering ropes according to EN 892:2012+A3:2023. In case of abseiling and lowering down, this also applies to braking devices used with low stretch kernmantel ropes in accordance with EN 1891.
It does not apply to manual braking devices and braking devices with assisted locking which are addressed in EN 15151-1 and EN 15151-2, nor to fully automatic fixed installations.

This document of the EN 12255 series specifies design principles and performance requirements for secondary and tertiary treatment of wastewater in biological fixed-film reactors at wastewater treatment plants for more than 50 PT.
Its primary application is for wastewater treatment plants for the treatment of domestic and municipal wastewater. It can also be applied for biodegradable industrial wastewater.
Biological fixed film reactors include rotating biological contactors (RBC), biological trickling reactors (BTR), moving bed biological reactors (MBBR), submerged medium reactors (SMR) and submerged media filters (SMF). Membrane bioreactors (MBR) and anaerobic processes are not within the scope.
Some of the systems using fixed film bacteria are enhanced activated sludge systems (hybrid systems). For such systems, EN 12255-6 also applies.
This document specifies fundamental information about typical systems and does not provide information about all available fixed film systems.

This document gives guidance, what measures can be taken in daily business already today to contribute to decarbonisation, resource efficiency and sustainability in the concrete sector.
Although concrete structural elements can be supplemented by other materials either for new construction or the retrofit of a structure, this document addresses concrete elements, bearing in mind the possibilities to increase resource efficiency and reuse of structures.

This document provides requirements and recommendations related to the concepts required to associate pharmaceutical products or groups of pharmaceutical products with an appropriate set of PhPID(s) in accordance with ISO 11616.
Pharmaceutical product identifiers and the related elements are intended to represent pharmaceutical products as defined within a medicinal product by a medicines regulatory authority. While the ISO standards on IDMP can be applied to off-label usage of medicinal products, such applications are currently outside of the scope of this document.
Reference to ISO 11238, ISO 11239, ISO 11240, ISO 11615, HL7 V3 messaging standards (HL7 Reference Information Model (RIM)[8], HL7 Common Product Model (CPM)[9] and HL7 V3 Structured Product Labelling (SPL)[10], and HL7 FHIR[11] can be applied for pharmaceutical product information in the context of this document.

This document specifies the requirements relating to:
Steel X5CrNiCu17-4 (1.4542)
Air melted
Solution treated and precipitation treated
Bars
a or D ≤ 200 mm
Rm ≥ 930 MPa
for aerospace applications.
W.nr: 1.4542.
ASD-STAN: FE-PM3801.

This document specifies the requirements for implementation of a quality system along the patient pathway in radiology services. The objective is to ensure high quality delivery of all aspects of the examination safety and patient care.
This document deals with procedures using X-rays, ultrasonography and magnetic resonance imaging on humans, including diagnostic procedures and interventional radiology as well as remote practices. It also applies, in its principles, to any other technique and modality that would be used in radiology services.
The document covers:
-   the different steps of patient care (from the imaging referral, before, during, and after the examination);
-   the corresponding human resources and technical-medical requirements;
-   quality and risk management.
This document does not apply to radiotherapy and nuclear medicine, nor to equipment and radiation controls which are covered in other standards. This document excludes requirements related to research and education themes.
This document establishes best practices description which constitutes a reference for audits, including clinical audits. Nevertheless, the clinical audits methodology, already defined at the European level, and implemented under the responsibility of each country is excluded from the document.

This document specifies requirements and provides recommendations for the design, equipment and operation of interpreting hubs for simultaneous interpreting. This document also ensures the usability and accessibility of interpreting hubs for all interpreters.
This document builds upon ISO 20109 and ISO 24019, which both contain requirements and recommendations regarding the equipment necessary for simultaneous interpreting.

This document specifies the behaviour of web application programming interfaces (APIs) that provide access to tiles of one or more geospatial data resources (collections) that the web API offers.
This document describes how to:
discover which resources offered by the web API can be retrieved as tiles;
get metadata about the available tile sets (including according to which tile matrix set each tile set is partitioned and the limits of that tile set within a common potentially global tile matrix set);
request a tile.
The core conformance class is defined in a way that can be easily included in a web API, even if that API does not conform to the OGC API  –  Common Standard. A web API can combine some requirements classes of this document with those of other OGC API standards (including OGC API  –  Common) to extend the scope of the web API by adding functionality.

This document compiles scientific and technical information on the composition of ELT derived rubbers aiming at helping ELT recyclers and producers of ELT derived rubbers complying with the main requirements of the European CLP and REACH regulations.
This document builds on existing literature data and on the REACH guidance on waste and recovered substances to:
— identify the relevant hazardous substances expected in ELT derived rubbers and the expected concentration ranges;
— assess the hazardous classification of the material according to the CLP Regulation;
— support the exemption from REACH registration requirements as provided by article 2.7(d) to REACH.

IEC 63545:2026 specifies safety requirements for horticultural luminaires, incorporating electric light sources for operation from supply voltage up to 1 000 V.

This document specifies requirements for the chemical and physical properties as well as quality control procedures for ground limestone for use as an addition in concrete.
This document is also applicable to ground limestone to be used in mortars and grouts.
This document does not specify provisions for the use of ground limestone in the production of concrete.

This document specifies the methods used for the chemical analyses and the determination of physical properties of calcium carbonate, high-calcium lime, half-burnt dolomite, magnesium oxide, calcium magnesium carbonate and dolomitic lime used to treat water for human consumption.
This document specifies the reference methods and, in certain cases, an alternative method which can be considered to be equivalent.

IEC 60444-11:2026 defines the standard method of measuring load resonance frequency fL at the nominal value of CL, and the determination of the effective load capacitance CLeff at the nominal frequency for crystals with the figure of merit M > 4.
This edition includes the following significant technical changes with respect to the previous edition:
a) key content of withdrawn IEC TR 60444-4 is reproduced as Annex A;
b) some formulae in the first edition have been corrected.

This document shows measures and potentials in the medium and long term to contribute to decarbonisation, resource efficiency and sustainability in the concrete sector compared to those measures that can already be taken in daily business today. Reduction of GHG emissions and resource efficiency are to be addressed at the same time and can affect each other; e.g. decreasing amount of fly ash in some countries due to the decommissioning of coal-fired power plants. As the embodied carbon in construction accounts for approx. 25-30 % of the GHG emissions of the life cycle of a typical building today, it has to be embedded into a LCA approach for the whole service life.
On CEN-Level as a consequence the general question is: “What can be done in the standards to go further in supporting decarbonisation, resource efficiency and sustainability in the concrete sector in the best possible way.
Values in the annexes are subject to change over time e.g. based on changes in the respective standards.

This document specifies performance requirements for alternative core laminates intended for interior use, the core layer compositions of which are not covered by EN 438-3 [1], EN 438-4 [2], EN 438-5 [3], EN 438-6 [4] and EN 438-8 [5]. The core layer types (coloured core layer and metal reinforced core layer) are specified in this part of the EN 438 series.
NOTE   Regarding the test methods relevant to this document, see EN 438-2.

IEC 63356-1:2026 specifies data sheets of LED lamps and LED modules with a series of parameters per data sheet for a specific LED light source that enables interchangeability between products from different LED light source manufacturers.
NOTE Compliance criteria relating to data sheet parameters in this document are covered by IEC 63554 or IEC 62031 for safety, and IEC 63555 for performance.
This third edition cancels and replaces the second edition published in 2023. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) addition of datasheets for GJ6.6d-2-x capped LED lamps.