Search Catalog

This document provides requirements and guidance on the provision, arrangement, operation, management, use and design of port waste reception facilities (PRFs). In doing so, it provides a method for addressing ship-generated waste, cargo residues and operational residues at ports when the waste and residues are offloaded from the ship. This document addresses principles and issues on: the development of a port waste management strategy; the design and operation of PRF; PWMP development, implementation and compliance; and PRF management and accountability. This document is designed to be used by ports and terminals with existing PRFs that aim to refine their systems. It can also be used by new ports and terminals that are developing PRFs. This document has been designed to be used by ports and terminals of any size. It does not give specifics on the size or location of a PRF in each port, but provides a list of principles to be considered and applied to any size of type of port or terminal (e.g. marina, fishing port, container terminal, oil terminal, roll on/roll off terminal, cruise terminal, ferry terminal, bulk or general cargo terminal, ship repair or recycling facility, and offshore terminal). NOTE For inland ports and marinas and those ports that have entered regional arrangements for the provision of a PRF for inland operated vessels, refer to ISO 24146-2.

This document specifies methods for the determination of silicon, nitrogen, aluminium, iron, calcium, oxygen, carbon, fluorine, and chlorine in silicon nitride powders. This document is applicable for the chemical analysis of silicon nitride powders used as raw material for fine ceramics.

This document specifies the requirements for devices which either limit or indicate, or limit and indicate the loads, motions, performance and environment of jib cranes. The general requirements for limiting and indicating devices for cranes are given in ISO 10245-1. This document applies to jib cranes (except for cantilever crane) as defined in ISO 4306-4. This document does not apply to the mobile, tower, railway, floating and offshore cranes defined in ISO 4306-1.

This document specifies the test method and procedure to evaluate the algal bloom removal rate using microbubbles in on-site microbubble-based algal-bloom removal facilities. The evaluation of the removal rate is conducted by comparing chlorophyll-a concentration before and after treatment using microbubbles. The range of water and weather conditions are served for test because they influence the characteristics of microbubbles and the algal bloom removal rate.

This document specifies requirements for utility lighters to ensure a reasonable degree of safety for normal use or reasonably foreseeable misuse of such lighters by users. This document applies to all flame-producing consumer products commonly known as utility lighters (also known as grill lighters, fireplace lighters, lighting rods or gas matches), and similar devices. It does not apply to matches and flame-producing products intended for igniting cigars, pipes and cigarettes.

This document provides guidelines, methodologies and techniques for securely deriving information about data assets from multiple sources, intermediaries or users, which is denoted as provenance metadata.

This document specifies requirements and associated test methods for assistive products for toileting, bathing and showering (from herein referred to as ‘assistive product’ within this document). NOTE 1 Some of the assistive products can be classified as medical devices. This document specifies safety, functional and ergonomic requirements for both persons with disability and assistants that apply during normal use and foreseeable misuse and failure. This document specifies requirements and test methods for assistive products within the following divisions of ISO 9999:2022. 09 12 03 Commode chairs; chairs, with or without castors, with a collection receptacle used for toileting away from the bathroom. 09 12 06 Toilets;1) included are, e.g. raised or height adjustable toilets, toilets with built-in douche and air dryers. 09 12 09 Toilet seats;1) devices attached to the toilet bowl or toilet chair for a person to sit on, which can provide stability and comfort. 09 12 10 Toilet splash guards;1) devices to keep bodily substances from splashing outside the toilet bowl. 09 12 12 Raised toilet seats, free-standing; raised toilet seats (separate) standing on floor, where the seat can easily be removed from the toilet bowl;included are, e.g. over toilet frames. 09 12 15 Raised toilet seats, detachable; raised toilet seats (loose attachments) placed directly on the toilet bowl/toilet seat where the seat insert can easily be removed from the toilet bowl/toilet seat. 09 12 18 Raised toilet seats fixed to toilet; devices permanently fixed on to a toilet bowl to increase the height of the seat and to facilitate sitting down upon, and standing up from, the toilet; included are, e.g. plinths. 09 12 21 Toilet seats with built-in raising mechanism to help standing up and sitting down; toilet seats that have a built-in lifting mechanism to assist a person to sit down on and get up from the toilet. 09 12 24 Toilet arm supports and toilet back supports mounted on toilet; devices mounted on the toilet that provide support getting on or off the toilet. 09 12 25 Toilet arm supports and toilet back supports, free standing. 09 12 36 Douches and air dryers for attachment to a toilet;1) devices attached to a toilet to provide a water spray with or without air blowing afterwards to wash, and possibly dry, a person’s bottom while sitting on the toilet; included are, e.g. toilet seats with that function. 09 33 04 Bath boards; seats without back support placed on the rim across the bathtub. 09 33 05 Bath seats; seats hung from the rim of or placed in the bathtub; included are e.g. bath seats with or without backrest. 09 33 07 Shower chairs with and without wheels; devices for supporting sitting during showering; included are, e.g. shower stools. 09 33 08 Back supports for bath or shower; excluded are, e.g. back support cushions. 09 33 12 Bathing stretchers, shower tables and diaper-changing tables; stationary or portable tables, with or without castors, on which a person lies during bathing, showering or changing. NOTE 2 Mainstream diaper-changing tables for babies/toddlers are excluded. They are covered by EN 12221-1. 09 33 15 Wash basins;1) stationary or portable basins for water used when washing parts of the body. 09 33 18 Bidets;1) stationary or portable basins primarily intended for washing genitals and bottom. 09 33 36 Assistive products for drying oneself;1) devices and materials for enabling a person to dry their own body. 18 15 06 Height adjustable plinths and brackets; height-adjustable surfaces or brackets on which furniture (e.g. wash basins) can be mounted. 18 18 03 Handrails and support rails; bars, usually cylindrical, attached to a wall, floor or other stable structure that provide the means for a person to support or stabilize themselves using hands or arms while walking, e.g. up and down stairs or ramps or moving along corridors. 18 18 06 Fixed grab bars and handgrips; devices, usually straigh

The EN 4500 series specifies the rules for the drafting and presentation of metallic material standards for aerospace applications.
This Part 001 specifies the "General rules" framework valid for all parts.

The present document specifies test severities and methods for the verification of the required resistibility of equipment according to the relevant environmental class.
The tests in the present document apply to stationary use of equipment at weatherprotected locations covering the environmental conditions stated in ETSI EN 300 019-1-3 [1].

This document provides guidance on how to determine the relevant vehicle configuration information for software update engineering according to ISO 24089. This document contains definitions of elements of vehicle configuration information, relationships between such elements and examples of usage. This document does not prescribe formats for elements of vehicle configuration information or how such information can be collected, stored and exchanged.

This document specifies requirements for the approval of a welding process in a fixed plant, together with the requirements for subsequent welding production.
This document applies to new Vignole rails manufactured in accordance to EN 13674 1 and welded by flash butt welding to crossing components in a fixed plant, and intended for use on railway infrastructures.
This document applies to cast Manganese crossings manufactured to EN 15689, fabricated crossings manufactured from rail and crossings manufactured from forged/rolled premium steels.
NOTE   EN 14587-1 is also used for the flash butt welding of switches.
Sometimes special profiles exist in crossing construction, which are not rail profiles as defined in EN 13674 series (example: profile with machined off rail foot). In these cases, tests are defined by the railway authority in participation with the manufacturer.

IEC TS 63102:2026 highlights the recommended technical methods of grid code compliance assessment of renewable energy (RE) power plants connected to the grid, including wind power plants, photovoltaic (PV) power plants, and hybrid power plants. Hybrid power plants refer to wind/PV power plants equipped with energy storage systems or combined power plants based on wind, PV, and energy storage. The electrical behaviour of RE power plants in this document includes the operating area, control performance, fault ride-through capability, power quality, oscillation, and grid adaptability.
Compliance assessment is the process of determining whether the electrical behaviour of RE power plants meets the specific technical requirements in grid codes or technical regulations. The assessment methods include compliance field test, compliance simulation, hardware-in-the-loop (HIL) simulation and compliance monitoring. The input for compliance assessment includes relevant supporting documents, test results, validated simulation models, controller hardware, and continuous monitoring data. This document focuses exclusively on assessment methods from a technical perspective. It does not address certification-related procedures.
This document is applicable to RE power plants connected to the electrical power grid.
This second edition cancels and replaces the first edition published in 2021. This edition includes the following significant technical changes with respect to the previous edition:
a) in terms of scope, wind and PV power plants are replaced by the renewable energy power plants that includes wind power plants, PV power plants and hybrid power plants. Oscillation and grid adaptability are added in the assessment scope;
b) Clause 5 optimizes the descriptions of compliance field testing, compliance simulation, HIL simulation and compliance monitoring assessment methods, and recommends corresponding assessment methods according to different phases of renewable energy power plants and various assessment items;
c) Clause 6 supplements compliance field test methods for reactive power capability assessment;
d) Clause 7 adds synthetic inertia response and voltage slope control to control performance assessment, adjusts recommended contents for field testing and HIL simulation, f) improves applicable conditions and reference procedures of assessment methods, and updates illustrative charts and figures;
e) Clause 8 adds cascaded under and over voltage ride-through assessment cases, and refines simulation procedures and requirements for simulation results;
f) Clause 9 incorporates compliance simulation and monitoring methods into power quality assessment;
g) oscillation assessment is newly introduced, adopting combined time-domain and frequency-domain simulation as well as monitoring methods, with the consideration of renewable energy power plants connected to grid via HVDC;
i) grid adaptability assessment is newly supplemented, specifically covering the following withstand capability, such as voltage unbalance factor, flicker and harmonics, phase angle jump and grid strength;
j) Annex A adds topological structure examples of renewable energy power plants, compliance simulation setup, and improves contents including HIL simulation setup, monitoring of electrical performance and harmonics simulation.

This document will provide means of compliance to cover lighting related requirements for Parts 2 to 4 of the Annex to the Commission Delegated Regulation (EU) 2019/945 on unmanned aircraft and on third country UAS operators.
The purpose is to be able to verify that an UA is equipped with lights:
—   for the controllability of the UA (the effectiveness of those lights is not part of the lighting requirement but is covered by the controllability requirement; therefore, its verification is covered by the clause addressing the controllability requirement of EN 4709 001:2026);
—   that ensure conspicuity of the unmanned aircraft at night (see 3.45 of ISO 21384 4:2025), the design of the light shall allow a person on the ground to distinguish a UA from a manned aircraft.
This document addresses:
—   definition of types, technical requirements, and technical parameters of UA lights (e.g. position of lights for different UA categories, intensity for different operation modes);
—   definition of purpose, test procedures, requirements, and compliance rules to evaluate UA lights

The EN 4500 series specifies the rules for the drafting and presentation of metallic material standards for aerospace applications.
This Part 005 specifies the "Specific rules for steels".

This document specifies a test method for determining the Vickers and Knoop hardness of monolithic fine ceramics at room temperature.

This document provides a general view of the most relevant requirements to ensure safety, reliability, system automation, security, comfort, interoperability and operations of the hyperloop system used for the transport of passengers and goods.
This document will be the basis to set the general common requirements for the hyperloop system as a whole.

This document defines front visibility conditions including positions of drivers and its assessment.
This document applies to metro vehicles with or without permanent driver, excluding shuttles used for short distance transportation.
Metro vehicle definition is according to EN 17343.
NOTE   For special vehicles, see EN 14033-4 and EN 15746-4.

The EN 4500 series specifies the rules for the drafting and presentation of metallic material standards for aerospace applications.
This Part 004 specifies the "Specific rules for titanium and titanium alloys".

This document specifies the electrolytic cadmium plating of parts and fasteners in steel of tensile strength UTS ≤ 1 450 MPa, copper, copper alloys and nickel alloys, whose temperature in service does not exceed 235 °C.

This document specifies a ultraviolet fluorescence method for the determination of trace sulfur in light olefins. This document is applicable to the determination of sulfur in ethylene, propylene, butadiene and other C4 olefins. The detection range for sulfur is from 0,2 mg/kg to 100 mg/kg.

The primary purpose of the ISO/IEC 19763 series is to specify a metamodel framework for interoperability. This document specifies a metamodel for registering administrative and evolution information of models of services, facilitating interoperability through the reuse of services. This document is only applicable to web services whose capabilities are described by some web service description language (see Annex A for examples of such languages). Figure 1 shows the scope of this document.

The EN 4500 series specifies the rules for the drafting and presentation of metallic material standards for aerospace applications.
This Part 006 specifies the "Specific rules for filler metals for brazing".

The EN 4500 series specifies the rules for the drafting and presentation of metallic material standards for aerospace applications.
This Part 002 specifies the "Specific rules for aluminium, aluminium alloys and magnesium alloys".

This document specifies requirements, test methods and pass criteria for the:
—   implemented static geocage function used to prevent the UA from breaching the horizontal and vertical limits of the planned operational volume;
—   information to be provided in the manufacturer’s instructions describing this function, its limits and the required size of the contingency volume after accounting the errors, reaction time and corrections.
This document does not cover the dynamic geocage function.
In addition, this document only covers the termination of the flight of the UA by the geo-caging function when breaching the OV. It does not address the compliance to the technical requirements imposed by Regulation (EU) 2019/945 on the Flight Termination System which are fully addressed by standard EN 4709-006, including the automatic triggering of the termination performed independently from the geo-caging function.

This document specifies the concepts of operation, minimum functionality, system requirements, system interfaces and test procedures for pedestrian detection and collision mitigation systems (PDCMS), which can reduce the likelihood of fatality and severity of injury. A PDCMS requires information about range to pedestrians, motion of pedestrians, motion of the subject vehicle (SV), driver commands and driver actions. It specifies the behaviours that are required for PDCMS, and the system test criteria necessary to verify that a given implementation meets the requirements of this document. Implementation choices are left to system designers wherever possible. Systems that include other countermeasures such as evasive steering are not within the scope of this document. Responsibility for the safe operation of the vehicle remains with the driver. This document applies to light duty passenger vehicles. It does not apply to other vehicle categories such as heavy vehicles or motorcycles. PDCMS are not intended for off-road use.

This part of IEC 60947 provides additional requirements to those given in IEC 60947-5-2 and IEC 60947-5-1:2024, Annex D (reed contact magnetic switches). It addresses the fault performance aspects of proximity devices with a defined behaviour under fault conditions (PDDB). It does not address any other characteristics that can be required for specific applications.
This document does not apply to protective equipment to directly detect the presence of persons, that are covered by the IEC 61496 series or IEC TS 62998 series.
NOTE 1 A PDDB device can be used to detect indirectly the presence of a person, for example by detecting the position of a platform on which the operator stands (example, garbage trucks).
This document does not specify requirements for the analogue output of PDDB, if any.
This document does not deal with any specific requirements on acoustic noise as the noise emission of proximity devices is not considered to be a relevant hazard.
A PDDB product is intended to be used as sensing subsystem of a safety related control system according to IEC 62061 or ISO 13849-1. Depending on construction principles and complexity, this document is based on product development of the IEC 61508 series to meet the product specific requirements of one or more of the following:
– IEC 61508 series;
– IEC 62061;
– ISO 13849 series.
NOTE 2 The Functional safety device type classification regarding functional safety correlates with IEC 62683-2-3.
This document includes requirements for PDDB when designed for use as part of an interlocking device according to ISO 14119.
This document does not consider aspects of:
– software updates and self-evolving behaviour;
– explosive atmospheres.

IEC 63407:2026 is applicable to automatic couplers, consisting of an automated connection device (ACD) and an ACD counterpart, of standardized configuration, intended for use in electric vehicle conductive charging systems which incorporate control means, with rated operating voltage up to 1 500 V DC. This document applies to high power DC interfaces intended for use in isolated conductive charging systems, for circuits specified in IEC 61851‑23‑1.
The requirements of this document apply only to automatic couplers defined in Annex A, Annex B, Annex C and Annex D of this document.

This document specifies methods of measuring the strippability and adherence of the insulation to a conductor of a finished cable.
When a particular method is not specified in the detail product specification, method A is the default test method.
Method B is suitable for wires insulated with materials showing a low adhesion to the conductor due to the poor repeatability of the test method A with this type of wires.
This document is intended to be used together with EN 3475-100.

This document specifies the fundamental principles and concepts of conformity assessment schemes (programmes) and provides guidelines for understanding, developing, operating or maintaining them.

This document specifies checks, measurement methods and procedures in order to verify the fitness for purpose of the installed ventilation systems and air conditioning systems according to design.
It establishes a procedure intended to technically support the handing over and inspection of these systems.
This document enables the choice between checks and measurements when sufficient, and additional measurements, when necessary.
This document applies to mechanical ventilation systems (including the mechanical part of hybrid systems) and full and (partial) air conditioning systems in non-residential (parts of) buildings.
This document does not apply to:
—   heat generating systems and their control;
—   refrigerating systems and their control;
—   distribution of heating and cooling medium to the air handling units;
—   compressed air supplying systems;
—   water conditioning systems;
—   central steam generating systems for air humidifying;
—   electric supply systems.
This document is not applicable to ventilation systems and air conditioning systems for industrial or other special process environments.

This document specifies a gas chromatographic method for the determination of trace amounts of oxygenated compounds in ethylene and propylene (propene) for industrial use. This document is applicable to ethylene and propylene having methanol, dimethyl ether, methyl tert-butyl ether, acetaldehyde, ethanol, propan-2-ol, acetone, and butanone concentrations greater than 0,5 mL/m3.

This document provides technical specification and specifies verification methods to support compliance with Commission Delegated Regulation (EU) 2019/945 of 12 March 2019 amended by Commission Delegated Regulation (EU) 2020/1058 of 27 April 2020 on unmanned aircraft systems (UAS) and on third-country operators of unmanned aircraft systems.
This includes compliance with product requirements for UAS intended to be operated under a standard scenario in the ‘specific’ category (class C5 and class C6 UAS).
This document is only applicable for unmanned aircraft (UA) with energy sources based on electro-chemical technologies.
Additional hazards that occur from the characteristics of the payload are excluded and are under the responsibility of the manufacturer and operator.
The present document covers requirements expressed in Annex, Part 16 requirements (1), (3), (4) and (6) and Part 17 requirements (1), (3), (6) and (7) of the Regulation 2020/1058.

This document is applicable to UAS and groups of UAS used in staging and production facilities for events and theatrical productions (entertainment industry). Such facilities include: theatres, multi-purpose halls, exhibition halls; film, television and radio studios; concert halls, schools, bars, discotheques, open-air stages and other rooms for shows and events.
This document is applicable to all UAS used in the entertainment industry, indoors and outdoors. This document includes UAS that are excluded from the Commission Delegated Regulation (EU) 2020/1058 and (EU) 2019/945 specifically Article 2, 4 which excludes “UAS intended to be exclusively operated indoors”.
This document deals with all significant hazards, hazardous situations or hazardous events relevant to UAS, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.
The document specifies the additional hazards and safety requirements for UAS categorized under the “open” category, the “specific” category, and the “certified” category, in particular, those that occur from the specific characteristics of the payload and the environment in the entertainment industry.
The principles in this document are also applicable to UAS based on new technologies or specially designed UAS which are not expressly mentioned here but which nevertheless operate in a similar manner or are meant for similar purposes to the equipment listed above.

This document specifies a gas chromatographic (GC) method for the determination of traces of carbon monoxide and carbon dioxide in ethylene and propylene for industrial use. This document is applicable to ethylene and propylene having carbon monoxide and carbon dioxide concentrations greater than 0,5 mL/m3.

This document specifies a method for measuring the corrosion loss of each part of structures using unpainted steel such as weathering steel by using the attached coupons. This document also provides a prediction method for corrosion loss over a long period from the measurement results and a method for determining the applicability of existing and new constructing weathering steel structures.

This document provides technical specification and verification methods to support compliance with Commission Delegated Regulation (EU) 2019/945 of 12 March 2019 on unmanned aircraft systems and on third-country operators of unmanned aircraft systems.
This part provides requirements, test methods and pass criteria for the means to terminate flight (flight termination) for unmanned aircraft systems, in particular addressing:
— safety related aspects of the architecture;
— descent performance;
— means to reduce the effects of impact on ground; and
— manufacturer’s instructions.
Even if security, including IT security, may be useful from an operational point of view, it falls outside the scope of this document.
An activation of the means to terminate the flight by a visual observer is also outside the scope of this document.
This document provides voluntary means of demonstrating compliance with the requirements laid out in Regulation (EU) 2019/945.
Additional hazards that occur from the characteristics of the payload are excluded and are, conversely, under the responsibility of the UAS manufacturer and UAS operator.

This document specifies the dimensional requirements of end-connections for high-pressure fuel injection equipment components, including fuel injectors, CR injectors, common rails, distribution blocks, injection pumps and high-pressure supply pumps used on diesel (compression-ignition) engines. It is applicable to externally threaded 60° concave cones (see Figures 1, 2, 5, and 6) and intended for use with high-pressure fuel injection pipe assemblies with tube outside diameters of: up to and including 12 mm for integral concave cones (see Table 1); and up to and including 9 mm for fabricated concave cones (see Table 2).

This document specifies a text file format − XML file format − for reporting natural gas analysis results and other data relevant to natural gas, natural gas substitutes and other combustible gaseous fuels. The file name is applicable when it includes the extension of .XML (case insensitive). The XML file format is useful for output from, for example, ISO 6974-1 for composition, ISO 19739 for sulfur compounds and ISO 6974-2 for uncertainty, as input for ISO 6976 for properties calculation or ISO 10723 for performance evaluation. Typically, these are the gas composition as provided on an analysis certificate. The format can also be used for the results of properties calculation or a performance evaluation that can be read into a spreadsheet editor or data processing.

The purpose of this document is to provide methods for quantifying the ride comfort of a passenger in a rail vehicle in response to the track sections it is operated over.
The methods aim to quantify the effects of vehicle body motions on ride comfort and to make the assessment of passenger comfort predictable, repeatable, objective and meaningful.
The methods and comfort scales are validated for people of good health.
This document applies to passengers in rail vehicles operating on heavy rail networks.
This document applies to measurements of motions. It also applies to simulated motions. Guidance is provided on:
-   which method described within the document should be used for different scenarios;
-   typical values for different comfort levels;
-   the application of simulation.
This document excludes health and safety issues, non-passenger carrying vehicles, vehicle homologation and safety, limit values, motion sickness, discomfort caused by accelerating and braking, design guidelines and measurement technology.

This document specifies the characteristics of inch based spherical plain bearing, metal to metal, in corrosion resisting steel, narrow series.
They are intended for use in fixed or moving parts of the aircraft structure and their control mechanisms.
They are used in the temperature range as determined by the grease capability as below:
-   code A: greased as per MIL-PRF-23827 Type I, operating temperature range −73 °C to 121 °C;
-   code B: greased as per MIL-PRF-81322, operating temperature range −54 °C to 177 °C.
The range of application for bearings lubricated with grease per code A is limited to 121 °C.
In both cases the spherical surface of the outer or inner ring are provided with a dry-film lubricant as per MIL-PRF-46010 or equivalent (anti-seizing protection).
The slide hole treatment either at the outer ring or inner ring.

The EN 4500 series specifies the rules for the drafting and presentation of metallic material standards for aerospace applications.
This Part 003 specifies the "Specific rules for heat resisting alloys".

IEC 60794-3-11:2026 sets forth detailed requirements and characteristics specific to this type of optical fibre cables for duct, direct buried, and lashed installation. This document includes functional, mechanical, environmental and optical requirements, recommended features and test methods for assessing the product against the stated requirements. The specified test methods, where applicable, are those referenced in IEC 60794-1-1 and IEC 60794-1-2. The requirements of this document supplement those of the sectional specification IEC 60794‑3 and the family specification IEC 60794-3-10.
This edition includes the following significant technical changes with respect to the previous edition:
a) subclause 5.2.2 has been enlarged to include fibre type B-657.B2;
b) this document has been updated to include multimode optical fibres.

This document specifies requirements for processed or semi-processed dried leaves of Origanum vulgare L. (including subspecies), in the whole or ground (powdered) form. This document does not apply to the requirements of Origanum majorana L., for which a separate document exists, see ISO 10620:1995. Recommendations relating to storage and transport conditions are given in Annex A.

This part of IEC 60851 specifies the following tests:
– Test 5: Electrical resistance;
– Test 13: Breakdown voltage;
– Test 14: Continuity of insulation;
– Test 19: Dielectric dissipation factor;
– Test 23: Pin hole.
For definitions and general notes on methods of test, Clause 3 of IEC 60851-1:2021 applies.
This part of IEC 60851 also specifies methods for determining the dissipation factor of enamelled winding wire, provided in Annex A.

This document specifies two methods for the determination of the tear strength of flexible cellular polymeric materials: Method A, using a trouser test piece; Method B, using an angle test piece without a nick.

This document specifies requirements for the specification and qualification of brazing procedures for brazing of metallic materials. This document specifies requirements for brazing of the test piece, testing of the test specimen, essential variables and their range of qualification, acceptance criteria, brazing procedure qualification record (BPQR) and brazing procedure specification (BPS). This document does not cover testing of residual stresses, corrosion resistance and impact properties. This document applies to the following brazing processes according to ISO 4063:2023 with local and global heating: 911 Infrared brazing; 912 Flame brazing, torch brazing; 913 Laser beam brazing; 914 Electron beam brazing; 916 Induction brazing; 918 Resistance brazing; 919 Diffusion brazing; 921 Furnace brazing; 922 Vacuum brazing; 923 Dip-bath brazing; 924 Salt-bath brazing; 925 Flux bath brazing; 926 Immersion brazing; 972 Arc weld brazing. This document does not apply to brazing for aerospace applications covered by ISO 11745.

This document provides an overview of the ISO 20271 series. The following are covered in this document: the scope and structure of the ISO 20271 series; description of textual document files within the scope of the ISO 20271 series; a summary of the content of each part in the ISO 20271 series; guidelines for the extension of other types of document formats.