Search Catalog

This document covers the design of any rigid PET packaging that does not fall within the definition of a PET bottle as outlined in Part 4 of this document, with respect to compatibility of the design with the state-of-the-art collection, sorting and recycling processes and useability of the recyclates in an application.
Packaging constituents and packaging components made of materials other than PET are also covered by this document as they need to be evaluated on compatibility with PET polymer recycling.

NOTE 1        There is guidance or rationale for this Clause in A.2.1.
This document specifies the requirements for information supplied by the manufacturer for a medical device or an accessory, as defined in 3.1. This document includes the generally applicable requirements for identification and labels on a medical device or accessory, the packaging, marking of a medical device or accessory, and accompanying information. This document does not specify the means by which the information is to be supplied.
NOTE 2        Some authorities having jurisdiction impose different requirements for the identification, marking and documentation of a medical device or accessory.
Specific requirements of medical device product standards or group standards take precedence over requirements of this document.

This document provides testing procedures and requirements on the evaluation processes for the sortability of plastic packaging with regard to compatibility of the design with state-of-the-art collecting and sorting processes for the plastic used.
This document covers any packaging predominantly made of plastic and separate packaging components predominantly made of plastic, both in case they undergo sorting processes.

This document covers the design of any rigid packaging with the main body of the packaging unit predominantly made of PE or PP and the design of separate components predominantly made of rigid PE or rigid PP, with respect to compatibility of the design with state-of-the-art collection, sorting and recycling processes and useability of the recyclates in an application.
Packaging constituents and packaging components made of other materials than PE and PP are also covered by this document as they need to be evaluated on compatibility with PE or PP polymer recycling.

This document provides requirements for the evaluation process of any rigid PET packaging that does not fall within the definition of a PET bottle as outlined in Part 4 of this document, with respect to compatibility of the design with state-of-the-art collection, sorting and recycling processes, and the characterization of the output(s) compared to a reference material.
Packaging constituents and packaging components made of other materials than PET are also covered by this document as they need to be evaluated on compatibility with PET polymer recycling.

This document provides a framework and principles for design for recycling documents for assessing the identification of the level of compatibility of plastic-packaging feature with the applicable collection, sorting and recycling processes, describing the level of compatibility.
This document covers any packaging predominantly made of plastic and separate components predominantly made of plastic. It aims to provide a consistent approach for the guidelines and protocols for each polymer and format.

This document covers the design of any bottle with the main body of the packaging unit predominantly made of PET and the design of separate components predominantly made of PET, with respect to compatibility of the design with state-of-the-art collecting, sorting and recycling processes and useability of the recyclates in an application.
Packaging constituents and packaging components made of other materials than PET are also covered by this document as they need to be evaluated on compatibility with PET polymer recycling.

This document covers the design of any flexible packaging with the main body of the packaging unit predominantly made of PE or PP and the design of separate components predominantly made of flexible PE or flexible PP, with respect to compatibility of the design with state-of-the-art collection, sorting and recycling processes and useability of the recyclates.
Packaging constituents and packaging components made of other materials than PE and PP are also covered by this document as they need to be evaluated on compatibility with PE or PP polymer recycling.

This document describes a test method for the determination of the flash point of chemicals, lube oils, fuels including aviation turbine fuel, diesel fuel, diesel/biodiesel blends and related products. The precision of this method has been determined over the range of 24,5 °C to 229,5 °C.
NOTE            Apparatus can determine the flash point at higher or lower temperatures than the precision range, however the precision has not been determined.

This document establishes the performance requirements for shank components for footwear, irrespective of the material, in order to assess the suitability for the end use and/or fitness for purpose. It also establishes the test methods to be used to evaluate the compliance with the requirements.
This document applies to shanks for all kinds of footwear as defined in Clause 4.
This document can be used as a reference by the manufacturer and the supplier.

This document specifies a test method for estimating the transfer of mineral oil saturated hydrocarbons (MOSH) and mineral oil aromatic hydrocarbons (MOAH) from food contact materials containing recycled pulp.
This test method is applicable for examining the extent of migration from paper and board equipped with a barrier or other technical solutions to reduce the amount of migration.
This test method is also applicable to paper and board made from virgin fibres.

This document provides general product category rules (PCR) for Type III environmental declarations for wood and wood-based products, including wood-based panels, for use in construction and related construction and in-service processes.
This document complements the core rules for the product category of construction products as defined in EN 15804 and is intended to be used in conjunction with EN 15804.
This document does not cover the assessment of social and economic performances at product level.
The core PCR:
—   define the parameters to be declared and the way in which they are collated and reported;
—   describe which stages of a product’s life cycle are considered in the EPD and which processes are to be included in the life cycle stages;
—   define rules for the development of scenarios;
—   include the rules for calculating the life cycle inventory and the life cycle impact assessment underlying the EPD, including the specification of the data quality to be applied;
—   include the rules for reporting predetermined, environmental and health information, that is not covered by LCA for a product, construction process and construction service where necessary;
—   define the conditions under which construction products can be compared based on the information provided by EPD.
For the EPD of construction services, the same rules and requirements apply as for the EPD of construction products.
Additionally, to the common parts of EN 15804, this document for wood and wood-based products:
—   defines the system boundaries;
—   defines the rules for modelling and assessment of material-specific characteristics such as carbon content and net calorific value of wood;
—   defines allocation procedures for multi-output processes along the wood chain;
—   defines allocation procedures for reuse, recycling and energy recovery;
—   includes the rules for calculating the life cycle inventory and the life cycle impact assessment underlying the EPD, including the assessment of carbon and net calorific value of wood;
—   provides guidance/specific rules for the determination of the reference service life (RSL).

This document specifies common fundamental concepts for long term archiving and retrieval of mechanical CAD information for elementary parts and assemblies. It details the “fundamentals and concepts” of EN 9300-003:2012 in the specific context of long-term archiving of CAD mechanical models.
Mechanical CAD information is divided into assembly structure and geometrical information, both including explicit and implicit geometrical representation, geometric dimensioning and tolerancing with form features.
The EN 9300-1XX series is organized as a sequence of parts, each building on the previous ones in a consistent way, each adding a level of complexity in the CAD data model. This includes the detailing of relationships between the essential information for the different types of CAD information covered by the EN 9300-1XX series.
As technology matures, additional parts will be released in order to support new requirements within the aerospace community.
1.2 In Scope
This document specifies:
- the fundamentals and concepts for long-term archiving and retrieval of 3D mechanical CAD information;
- the document structure of the EN 9300-1XX series, and the links between all these parts;
- the qualification methods for long-term preservation of archived mechanical CAD information; more specially, principles for the CAD validation properties and for verification of the quality of the CAD archived file;
- specifications for the preservation planning of archived CAD information;
- specific functions for administration and monitoring of CAD archived mechanical models;
- the definition of archive information packages for CAD data.
1.3 Out of scope
The following are out of scope for this part:
- long-term archiving of CAD 2D drawings;
- other CAD specialization disciplines, such as electrical harnesses, composite.

This document specifies a procedure for the determination of the dimensional changes and distortion out of plane likely to take place when textile floor coverings and tiles are subjected to varied water and heat conditions.
The method is applicable to all textile floor coverings and textile floor coverings in tile form.

This document is applicable to the tensile testing and specifies the requirements of metallic materials at elevated temperature for aerospace applications.
It is applied when referred to in the EN technical specification or material standard unless otherwise specified on the drawing, order or inspection schedule.

This document specifies requirements and test methods for durability, strength, security and functionality of sliding closing devices (SCDs) for windows and door height windows.
This document does not specifically cover the handles used in handle-operated SCDs or the sash fasteners used in cam-operated SCDs, requirements and test methods for which are given in EN 13126 2, EN 13126 3 and EN 13126 14, respectively.
The performance tests incorporated in this document are considered to be reproducible and as such will provide a consistent and objective assessment of the performance of these products throughout CEN Member States.

This document specifies a method [1] for the quantitative determination of saxitoxin (STX), decarbamoyl saxitoxin (dcSTX), neosaxitoxin (NEO), decarbamoyl neosaxitoxin (dcNEO), gonyautoxin 1 and 4 (GTX1,4; sum of isomers), gonyautoxin 2 and 3 (GTX2,3; sum of isomers), gonyautoxin 5 (GTX5), gonyautoxin 6 (GTX6), decarbamoyl gonyautoxin 2 and 3 (dcGTX2,3; sum of isomers), N-sulfocarbamoyl gonyautoxin 2 and 3 (C1,2; sum of isomers) and N-sulfocarbamoyl gonyautoxin 1 and 4 (C3,4; sum of isomers) in (raw) mussels, oysters, scallops and clams. Laboratory experience has shown that this document can also be applied to other marine invertebrates [2], [3] and processed products of those species, however, no complete interlaboratory validation study according to ISO 5725-2 [21] has been carried out so far. The method described was validated in an interlaboratory study [4], [5] and was also verified in a European Union Reference Laboratory for Marine Biotoxins (EURLMB)-performance test aiming the total toxicity of the samples [6]. Toxins which were not available in the first interlaboratory study [4], [5] as dcGTX2,3 and dcNEO were validated in two additional interlaboratory studies [7], [8]. The lowest validated levels [4], [5], [8], are given as mass fraction of toxin (free base) in µg/kg shellfish tissue and also as µmol/kg shellfish tissue and are listed in Table 1.
[Table 1 - Lowest validated levels]
A quantitative determination of GTX6 was not included in the first interlaboratory study but several laboratories detected this toxin directly after solid phase extraction with ion-exchange (SPE-COOH) clean-up and reported a mass fraction (free base) of 30 µg/kg or higher in certain samples. For that reason, the present method is applicable to quantify GTX6 directly, depending on the availability of the standard substance. Whenever GTX6 standard is not commercially available, it is possible to determine GTX6 after hydrolysis of Fraction 2 of the SPE-COOH clean-up, described in 7.4, as NEO. The indirect quantification of GTX6 was validated in two additional interlaboratory studies [7], [8]. A study to compare direct and indirect GTX6 quantification was conducted at the EURLMB [16].
A quantitative determination of C3,4 was included in the first interlaboratory study. The present method is applicable to quantify C3,4 directly, depending on the availability of the standard substance. If no standard substances are available, C3,4 can only be quantified as GTX1,4 if the same hydrolysis protocol used for GTX6 (7.4) is applied to Fraction 1 of the SPE-COOH clean-up [10]. A study to compare direct and indirect C3,4 quantification was conducted at the EURLMB [16].

This document specifies the conditions for the determination of the tensile creep deformation and failure of single filaments of ceramic fibres at high temperature and under test conditions that prevent changes to the material as a result of chemical reaction with the test environment.
This document applies to continuous ceramic filaments taken from tows, yarns, braids and knitted structures, that have strains to failure less than or equal to 5 %.

This document gives guidance on the use of regrinds and recycled materials for thermoplastic parts for aerospace use.
This document does not apply to reinforced thermoplastic materials, such as short fibre-reinforced plastics, due to their distinct processing characteristics, material degradation concerns, and stringent aerospace performance requirements.
The intended manufacturing processes for these virgin/regrind blends include standard thermoplastic methods such as injection moulding, extrusion, and blow moulding, among others as appropriate to the application.

This document specifies general construction, performance and material requirements for PN 10 thermostatic mixing valves (TMV) and includes test methods for the verification of mixed water temperature performance at the point of use below 45 °C. This does not exclude the selection of higher temperatures where available. When these devices are used to provide anti-scald protection for children, elderly and disabled persons the mixed water temperature shall be set at a suitable temperature (body temperature - 38 °C). In particular children are at risk to scalding at lower temperatures than adults. This does not obviate the need for supervision of young children.
It applies to valves intended for use on sanitary appliances in kitchens, washrooms (incl. all rooms with sanitary tapware, e.g. toilet and cloakrooms) and bathrooms operating under the conditions specified in Table 1.
This document allows TMVs to supply a single outlet or a small number of outlets in a “domestic” application (e.g. one valve, controlling a shower, bath, basin and/or, bidet), excluding valves specifically designed for supplying a large number of outlets (i.e. for institutional use).
The tests described are type tests (laboratory tests) and not quality control tests carried out during manufacture.

This document is applicable to flushing valves for WCs and valves for urinals, with automatic hydraulic closure, intended for:
—   WC pans EN 997;
—   single flush urinals EN 13407;
—   siphon acting urinals EN 13407.
It does not apply to no-contact detection valves.
It is intended to specify:
—   marking and identification, physico-chemical, dimensional, leaktightness, pressure behaviour, hydraulic, mechanical endurance and acoustic characteristics of flushing valves for WCs and urinals with automatic closure;
—   test methods used to verify these characteristics;
—   and to determine requirements for the atmospheric interrupter which shall be an integral part of the WC flushing valve.
It is applicable in the following pressure and temperature conditions (see Table 1):
[Table 1 — Conditions of use for tapware]
NOTE   Although this document limits the pressure for WC DN25 and WC DN32 valves till 0,25 MPa (2,5 bar), some European countries have legislation and recommendations for higher pressures.
Health and quality requirements in accordance to European and national legislation for final materials in contact with water intended for human consumption are not covered by this document.

This document specifies the requirements for design, manufacture and installation of metal bellows expansion joints with circular cross section for pressure applications with maximum allowable pressure greater than 0,5 bar.

This document specifies the safety requirements for reciprocating internal combustion (RIC) engine driven generating sets up to 1 000 V alternating current (AC) or 1 500 V direct current (DC) and voltages above 1 000 V (AC) and not exceeding 36 kV consisting of an RIC engine, an AC generator including the additional equipment required for operating, e.g. controlgear, switchgear, auxiliary equipment.
This document is applicable to generating sets for land and marine use (domestic, recreational and industrial application). This document is not applicable to generating sets used on board of seagoing vessels and mobile offshore units as well as on aircraft or to propel road vehicles and locomotives.
This document is not applicable to gensets and components manufactured before the date of its publication.
NOTE            This document does not apply to arc welding equipment (IEC 60974 series).
This document does not specify the special requirements needed to cover operation in potentially explosive atmospheres and is not applicable for such environments.
The hazards relevant to RIC engine driven generating sets are identified in Table A.1.
This document deals with the special requirements of test and safety design which are observed in addition to the definitions and requirements in ISO 8528-1:2018, ISO 8528-2:2018, ISO 8528-3:2020, ISO 8528-4:2025, ISO 8528-5:2025, ISO 8528-6:2023 and ISO 8528-10:2022, where applicable. This document specifies safety requirements in order to protect the user from danger.

The contents of the corrigendum of March 2023 have been included in this copy.

IEC 63316:2026 prescribes safeguards, test methods and compliance requirements intended to reduce the risk of electrical shock and fire associated with voltage and current at voltages greater than 60 V DC and 60 V AC. This document applies to equipment ports intended to supply and receive operating power from communications equipment ports using communication wires and cables. It covers particular requirements for circuits that are designed to transfer AC or DC power from a power sourcing equipment (PSE) (3.1.2) to a powered device (PD) (3.1.3), including repeaters, amplifiers, Optical Network Units, Remote DSLAMs, service provider terminating equipment, remote telecommunications cabinets and equipment, and midspan passive equipment connected to the PSE (3.1.2) and PD (3.1.3). The power transfer of equipment ports covered by this document uses non-mains AC voltage or non-mains DC voltage above 60 V DC classified as ES2 according to 5.2.1.2 of IEC 62368-1:2023 or, in some very controlled cases, classified as ES3 according to IEC 62368-1:2023. EXAMPLES - DC power transfer using voltages above 60 V DC but ≤ 120 V DC, classified as ES2; - Some telecommunications networks where the voltage was formerly called TNV-3 (see IEC 62368-1:2023, Table W.3), typically used for line, span or express powering outside North America, Long Range Reverse Power Feeding, HDSLx line powering ISDN, Line Powering Primary Rate E1; - Some North American telecommunications networks between the utility service providers´ PSE (3.1.2) and service providers side of the PD (3.1.3) at the PNI (3.1.8); - For DC power transfer using voltages ≥ 120 V DC at ES3: RFT circuits and the associated telecommunications network equipment and cabling used by communications service providers and communications utilities (for example, line powered E1/T1, HDSLx, SHDSLx, xDSL, repeaters, and telecommunications line powering up or line powering down converters as applicable), Optical Network Units, remote DSLAMs, etc. These RFT circuits are used between the utility service providers PSE (3.1.2) and service providers side of the PD (3.1.3) at the PNI (3.1.8). The customer facing ports of this equipment are at voltage not exceeding 60 V DC and are covered by IEC 62368-1:2023, see Annex A for deployment topologies; - For AC/DC remote powering voltage above ES1 over coaxial cable in circuits used by cable television utility service providers for repeaters, amplifiers, Optical Network Units. The customer facing ports of this equipment are at voltage not exceeding 60 V DC that are covered by IEC 62368-1:2023. NOTE 1 Any communications cable that permits power transfer between communication equipment is considered a communication cable even if communication does not take place. For example, a line powering up or line powering down converters as applicable used to power remote telecommunications equipment, can provide limited communications RFT power and not necessarily any superimposed data or signalling. This document does not cover equipment interfaces within the scope of IEC 63315. NOTE 2 IEC 63315 covers equipment intended to either supply or receive charging, or operating power from ICT interfaces using ICT wires and cables such as PoE, USB, HDMI, etc, or any of these combined. This document does not cover ringing signals that are in the scope of IEC 62368-1 or in the scope of IEC 62949:2017. This document does not cover traditional telecommunications technologies which operate at voltages not exceeding 60 V DC (circuits classified as ES1 according to 5.2.1.1 of IEC 62368-1:2023 and Tabl

IEC 61788-15:2026 describes measurements of the intrinsic surface impedance (Zs) of HTS films at microwave frequencies by a modified two-resonance mode dielectric resonator method. The object of measurement is to obtain the temperature dependence of the intrinsic Zs at the resonant frequency f0. The frequency and thickness range and the measurement resolution for the Zs of HTS films are as follows: - frequency: up to 40 GHz; - film thickness: greater than 50 nm; - measurement resolution: 0,01 mΩ at 10 GHz. It is crucial that the Zs data at the measured frequency, and that scaled to 10 GHz be reported for comparison, assuming the f2 rule for the intrinsic surface resistance, Rs (f < 40 GHz), and the f rule for the intrinsic surface reactance, Xs. This second edition cancels and replaces the first edition published in 2011. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - informative Annex B, combined relative standard uncertainty in the intrinsic surface impedance is added; - the terms, ‘precision and accuracy’, are replaced with uncertainty; - results from a round robin test are added.

This document contains requirements for the competence and impartiality of bodies performing inspection, and for the consistent operation of their inspection activities.

This part of IEC 60115 is applicable to fixed power resistors for use in electronic equipment.  
This standard relates to resistors having a rated dissipation typically greater than 1W up to and including 1000W for use in
electronic equipment. This standard is applicable to fixed power resistors with a maximum surface temperature (MET)
higher than the preferred upper category temperature (UCT) of 200°C.  
These resistors are typically described according to types (different geometric shapes) and styles (different dimensions)
and product technology.  
The resistive element of these resistors is typically  
- protected by a conformal lacquer coating or  
- cement coating or  
- vitreous enamel or  
- a ceramic body or  
- any other housing, which is to be described in the relevant specification.  
The electrical connection of these resistors is typically achieved by means of  
- lead wire terminations or  
- punched terminals or lug terminals or  
- push on terminals or  
- screw terminals or  
- any other termination, which is to be described in the relevant specification  
In special cases, a heat sink may be applicable but not mandatory.  
The object of this standard is to prescribe preferred ratings and characteristics and to select from IEC 60115-1 the
appropriate quality assessment procedures, tests and measuring methods and to give general performance requirements
for this type of resistor.  
Test severities and requirements prescribed in detail specifications referring to this sectional specification shall be of equal
or higher performance level, because lower performance levels are not permitted.
Since the documents of the 60115-X series are exempted from the parallel procedure (D162/C089), this New Work Item Proposal aims to endorse the main IEC document IEC 60115-4:2022 as a European standard. The standard shall be published together with the finalised Common Modifications.

This part of IEC 60115 is applicable to fixed power resistors for use in electronic equipment. This standard relates to resistors having a rated dissipation typically greater than 1W up to and including 1000W for use in electronic equipment. This standard is applicable to fixed power resistors with a maximum surface temperature (MET) higher than the preferred upper category temperature (UCT) of 200°C. These resistors are typically described according to types (different geometric shapes) and styles (different dimensions) and product technology. The resistive element of these resistors is typically - protected by a conformal lacquer coating or - cement coating or - vitreous enamel or - a ceramic body or - any other housing, which is to be described in the relevant specification. The electrical connection of these resistors is typically achieved by means of - lead wire terminations or - punched terminals or lug terminals or - push on terminals or - screw terminals or - any other termination, which is to be described in the relevant specification In special cases, a heat sink may be applicable but not mandatory. The object of this standard is to prescribe preferred ratings and characteristics and to select from IEC 60115-1 the appropriate quality assessment procedures, tests and measuring methods and to give general performance requirements for this type of resistor. Test severities and requirements prescribed in detail specifications referring to this sectional specification shall be of equal or higher performance level, because lower performance levels are not permitted

IEC 61400-40:2026 provides the EMC requirements and test methods that apply to the individual wind turbine and all the sub systems which are part of the wind turbine.
The current document applies to measurements on individual wind turbines and not multiple wind turbines.
This document defines the requirements and test methods for the verification of the wind turbine performance against radiated emissions and the immunity of their components against conducted and radiated phenomena. This document is applicable to onshore and offshore wind turbines.

This document specifies principles and requirements for a body operating certification of persons and includes the development and maintenance of a scheme for certification of persons.
NOTE 1        For the purposes of this document, the term "certification body" is used in place of the full term " body operating certification of persons", and the term "certification scheme" is used in place of the full term “scheme for certification of persons”.
NOTE 2        Annex A contains principles for certification of persons.

This part of IEC 60115 is applicable to fixed surface mount resistors for use in electronic equipment.
These resistors are typically described according to types (different geometric shapes) and styles (different dimensions)
and product technology. These resistors have metallized terminations and are primarily intended to be mounted directly
onto a circuit board.
The object of this document is to specify preferred ratings and characteristics and to select from IEC 60115-1, the
appropriate quality assessment procedures, tests and measuring methods and to give general performance requirements
for this type of resistor.
Since the documents of the 60115-X series are exempted from the parallel procedure (D162/C089), this New Work Item
Proposal aims to endorse the main IEC document IEC 60115-8:2023 as a European standard. The standard shall be
published together with the finalised Common Modifications.

This part of IEC 60115 is applicable to leaded fixed low-power film resistors for use in electronic equipment and is
applicable to the drafting of detail specifications for leaded fixed low-power film resistors classified to level G, which is
defined in IEC 60115-1:2020, 3.4 for general electronic equipment, typically operated under benign or moderate
environmental conditions, where the major requirement is function. Examples for level G include consumer products and
telecommunication user terminals.
The resistors covered herein are classified to level G, as defined in IEC 60115-1:2020, 3.4 for general electronic
equipment, typically operated under benign or moderate environmental conditions, where the major requirement is
function. Examples for level G include consumer products and telecommunication user terminals.  
Since the documents of the 60115-X series are exempted from the parallel procedure (D162/C089), this New Work Item Proposal aims to endorse the main IEC document IEC 60115-2-10:2023 as a European standard. The standard shall be published together with the finalised Common Modifications.

This part of IEC 60115 is applicable to fixed low-power film resistors with termination leads for use in electronic equipment, which are typically assembled in through-hole technology (THT) on circuit boards. These resistors are typically described according to types (different geometric shapes) and styles (different dimensions) and product technology. The resistive element of these resistors is typically protected by a conformal lacquer coating. These resistors have wire terminations and are primarily intended to be mounted on a circuit board in through-hole technique. The object of this standard is to prescribe preferred ratings and characteristics and to select from IEC 60115-1, the appropriate quality assessment procedures, tests and measuring methods and to give general performance requirements for this type of resistor. Since the documents of the 60115-X series are exempted from the parallel procedure (D162/C089), this New Work Item Proposal aims to endorse the main IEC document IEC 60115-2:2023 as a European standard. The standard shall be published together with the finalised Common Modifications.

This document provides requirements and recommendations related to the concepts required to associate pharmaceutical products or groups of pharmaceutical products with an appropriate set of PhPID(s) in accordance with ISO 11616. Pharmaceutical product identifiers and the related elements are intended to represent pharmaceutical products as defined within a medicinal product by a medicines regulatory authority. While the ISO standards on IDMP can be applied to off-label usage of medicinal products, such applications are currently outside of the scope of this document. Reference to ISO 11238, ISO 11239, ISO 11240, ISO 11615, HL7 V3 messaging standards (HL7 Reference Information Model (RIM)[8], HL7 Common Product Model (CPM)[9] and HL7 V3 Structured Product Labelling (SPL)[10], and HL7 FHIR[11] can be applied for pharmaceutical product information in the context of this document.

This part of IEC 60115 is applicable to leaded fixed low-power film resistors for use in electronic equipment and is applicable to the drafting of detail specifications for leaded fixed low-power film resistors classified to level G, which is defined in IEC 60115-1:2020, 3.4 for general electronic equipment, typically operated under benign or moderate environmental conditions, where the major requirement is function. Examples for level G include consumer products and telecommunication user terminals. The resistors covered herein are classified to level G, as defined in IEC 60115-1:2020, 3.4 for general electronic equipment, typically operated under benign or moderate environmental conditions, where the major requirement is function. Examples for level G include consumer products and telecommunication user terminals. This detail specification is based upon the blank detail specification IEC 60115-2-10:202X. This detail specification establishes test schedules and performance requirements permitting the quality assessment of the resistors covered herein according to the quality assessment procedures prescribed by IEC 60115-1:2020, Annex Q.

This part of IEC 60115 is applicable to fixed surface mount resistors for use in electronic equipment. These resistors are typically described according to types (different geometric shapes) and styles (different dimensions) and product technology. These resistors have metallized terminations and are primarily intended to be mounted directly onto a circuit board. The object of this document is to specify preferred ratings and characteristics and to select from IEC 60115-1, the appropriate quality assessment procedures, tests and measuring methods and to give general performance requirements for this type of resistor

IEC 63041-3:2026 is applicable to piezoelectric physical sensors mainly used in the field of process control, wireless monitoring, dynamics, thermodynamics, vacuum engineering, and environmental sciences. This document provides users with technical guidelines as well as basic knowledge of common physical sensors. Piezoelectric sensors covered herein are those applied to the detection and measurement of physical quantities such as force, pressure, torque, viscosity, temperature, film thickness, acceleration, vibration, and tilt angle.
This edition includes the following significant technical changes with respect to the previous edition:
a) Some terms in Clause 3 have been updated to be consistent with IEC TS 61994-5:2023.

This document specifies a test method for the determination of total amount of halogens (including fluorine, chlorine, bromine and iodine) present in textile products by combustion and ion chromatography (C-IC). This document is applicable to all materials of textile products which are combustible, e.g. fibres, fabrics, plastic components (including coating), wood.

This part of IEC 60115 is applicable to fixed low-power film resistors with termination leads for use in electronic equipment, which are typically assembled in through-hole technology (THT) on circuit boards.  
These resistors are typically described according to types (different geometric shapes) and styles (different dimensions)
and product technology. The resistive element of these resistors is typically protected by a conformal lacquer coating.
These resistors have wire terminations and are primarily intended to be mounted on a circuit board in through-hole
technique.  
The object of this standard is to prescribe preferred ratings and characteristics and to select from IEC 60115-1, the
appropriate quality assessment procedures, tests and measuring methods and to give general performance requirements
for this type of resistor.

This document specifies the classification, general requirements, design requirements, general characteristics, general testing and inspection methods for submersible toolings. This document applies to the design, manufacture, inspection, and post-acceptance of submersible toolings.

This document specifies the general requirements, test items and methods for conducting manoeuvring tests on human-occupied submersibles. It is applicable to manoeuvring tests for all human-occupied submersibles operating in the sea and inland waterway areas. It can also be used as a reference for manoeuvring tests on other types of submersibles operating in pools, lakes and seas.

This document specifies container file formats for JPEG AI codestreams as specified in Rec. ITU-T T.840.1 | ISO/IEC 6048-1 and Rec. ITU-T T.840.2 | ISO/IEC 6048-2. It defines file formats for working with image and motion sequence files on computer platforms, allowing Internet-based and other communications. This document uses already existing specifications for file formats and extends them for the embedding of JPEG AI codestreams.