SIST - Slovenian Institute for Standardization

This document specifies the physical and mechanical properties of pipes made from unplasticized polyamide (PA-U) in accordance with ISO 16486-1, intended to be buried and used for the supply of gaseous fuels.
It also specifies the test parameters for the test methods to which it refers.
The ISO 16486 series is applicable to PA-U piping systems, the components of which are connected by fusion jointing and/or mechanical jointing.
In particular, this document lays down dimensional characteristics and requirements for the marking of pipes.
Pipes conforming to this document are jointed typically by using mechanical, electrofusion or butt fusion techniques.

The particular requirements of this part of IEC 60364 apply to:
- fixed equipment within conducting locations with restricted movement; and
- supplies to equipment used within conducting locations with restricted movement.

This document establishes ergonomic design principles for interactive systems related to the software-controlled presentation of information by user interfaces. It applies to the three main modalities (visual, auditory, tactile or haptic) typically used in information and communication technology (ICT). These principles apply to the perception and understanding of presented information. These principles are applicable in the analysis, design and evaluation of interactive systems. This document also provides recommendations corresponding to the principles. The recommendations for each of the principles are not exhaustive and are not necessarily independent from one another.
While this document is applicable to all types of interactive systems, it does not cover the specifics of particular application domains which require context-specific recommendations. This document also applies to outputs from interactive systems (such as printed documents and document exports in common computer formats, e.g. pdf, text and tabular formats).

IEC 62074-1: 2025 applies to fibre optic wavelength division multiplexing (WDM) devices. These have all of the following general features:
- they are passive, in that they contain no optoelectronic or other transducing elements; however they can use temperature control only to stabilize the device characteristics; they exclude any optical switching functions;
- they have three or more ports for either the entry or exit of optical power, or both, and share optical power among these ports in a predetermined fashion depending on the wavelength;
- the ports are optical fibres, or optical fibre connectors.
This document establishes uniform requirements for the following:
- optical, mechanical and environmental properties.
This third edition cancels and replaces the second edition published in 2014. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) harmonization of terms and definitions with IEC TS 62627-09;
b) simplified classification, documentation and standardization system in Clause 4, and moving interface style to Annex H.

IEC 63522-29:2025 This part is used for testing the appropriate severities and conditions for measurements and tests designed to assess the ability of DUTs to perform under expected conditions of transportation, storage and all aspects of operational use.
It specifies how to ensure that the capacitances formed by parts of a relay do not exceed specified limits.

IEC 60068‑2-88:2025 establishes test methods for the resistance of electronic and electromechanical components, unpopulated circuit boards and assemblies to liquid cleaning media and cleaning processes, which are agreed between user and supplier for applications, where cleaning is required. These tests are not applicable to components, unpopulated circuit boards and assemblies, which are not intended to be subjected to cleaning processes.
Tests XD1 and XD2 primarily are intended for qualification testing of components and unpopulated circuit boards suitable for cleaning processes, but can be adopted as well to testing of material compatibility and specific cleaning media used in manufacturing processes of components and unpopulated circuit boards.
Test XD3 is intended to determine the resistance of electronic assemblies suitable for cleaning processes to the various cleaning processes to which they are exposed during manufacturing, including the effects of assembly and soldering processes.

This part of IEC 61340 provides electrical and mechanical test methods and performance limits for evaluation, acceptance and periodic verification testing of wrist straps.
NOTE All dimensions are nominal except where indicated.
This standard is intended for testing wrist straps and wrist strap systems used for the grounding of personnel engaged in working with ESD sensitive assemblies and devices.
It does not address constant monitoring systems.

IEC 60269-1:2024 is available as IEC 60269-1:2024 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.

IEC 60269-1:2024 is applicable to fuses incorporating enclosed current-limiting fuse-links with rated breaking capacities of not less than 6 kA, intended for protecting power-frequency AC circuits of nominal voltages not exceeding 1 000 V or DC circuits of nominal voltages not exceeding 1 500 V.

This document specifies requirements for fire activated oxygen shut-off devices that stop the flow of oxygen in respiratory therapy tubing when activated by fire.
NOTE 1        Typical arrangements for fire activated oxygen shut-off devices are shown in Annex C.
NOTE 2        Respiratory therapy tubing is covered by ISO 17256.
NOTE 3        Use of fire activated oxygen shut-off devices in medical devices or accessories is not mandated in this document.
The fire activated oxygen shut-off devices specified in this document are not suitable for use with oxygen therapy systems with flows in excess of 20 l/min).
NOTE 4        There is rationale for this clause in A.2.
The requirements in this device-specific standard take precedence over any conflicting requirements in the general standard for airway devices (ISO 18190). All the common requirements that appear in the general standard for airway devices have been removed from this document.

IEC 63366:2025 defines product category rules (PCR) for electrical and electronic products and systems (EEPS) to develop Type III environmental declarations for electrical and electronic products and systems (EEPS). It specifies the process and requirements on how to conduct life cycle assessment (LCA) in the context of environmental declarations.
This document provides common rules for:
a) LCA, including the requirements for developing default scenarios;
b) the LCA report;
c) the development of PSR.
This document provides further guidelines for environmental declarations.
The LCA principles and framework are based on ISO 14040 and ISO 14044, and are therefore out of scope of this document.
PCR is complemented by additional product-specific rules (PSR), which further define, for example, functional units and default scenarios in the product-specific context. Therefore, this document also provides guidance on how to develop PSR in corresponding technical committees.
This document has the status of a horizontal publication in accordance with IEC Guide 108. In accordance with IEC Guide 108, this generic essential horizontal standard is intended for use by product committees as a starting point in preparing PSR standards. Specific requirements developed by product committees in PSR standard take precedence over requirements in this standard.
When there is no PSR available in a product committee, this generic essential horizontal standard could be applied by LCA practitioners with recorded complementary specifications.

This European Standard advises on the safe use of ladders covered by the scope of EN 131-1 and fulfilling the requirements of EN 131-1, EN 131-2 and, for single or multiple hinged-joint ladders, EN 131-4, for telescopic ladders EN 131-6 and for mobile platform ladders EN 131-7.

This document specifies the general design features, requirements and test methods and defines terms for leaning and standing telescopic ladders.
Ladders with extension elements are not covered by this part of EN 131.
This part of the standard is intended to be used in conjunction with EN 131-1, EN 131-2, EN 131-3 and if applicable EN 131-4.

This document specifies the requirements, tests and marking of hinged combination ladders with one or several hinge joints.
This document is not applicable to hinge-joints of combination and standing ladders as defined by EN 131-1.
This part of the standard is intended to be used in conjunction with EN 131-1, EN 131-2 and EN 131-3.

This European Standard specifies the general design features, requirements and test methods for portable ladders.
It does not apply to step stools or ladders for specific professional use such as firebrigade ladders, roof ladders and mobile ladders.
It does not apply to ladders used for work on or near live electrical systems or installations. For this purpose EN 61478 applies.
NOTE   For insulating ladders for use on or near low voltage electrical installations EN 50528 applies.
This European Standard is intended to be used in conjunction with EN 131-1.
For single or multiple hinge joint ladders EN 131-4 applies.
For telescopic ladders EN 131-6 applies.
For mobile ladders with a platform EN 131-7 applies.

This document provides guidelines for the design, use and maintenance of hardened protective shelters (hereafter referred to as “shelters”). It specifies guidance on the layout, structures, equipment and actions related to a shelter.
This document is intended for organizations or individuals responsible for or involved in decision-making, planning, implementation, administration, use or upkeep of shelters, such as local, regional and national governments, civil protection agencies, first responders and businesses such as designers, constructers and equipment suppliers.
This document does not cover the minimum requirements or exact specifications for the properties of or actions related to a shelter; nor does it cover rapidly erected temporary shelters, such as lightweight canvas weather shelters, other tarp tent shelters, or metal and container shelters. Military shelters are subject to additional requirements which are outside the scope of this document.

This document specifies the requirements relating to the dimensional, mechanical and physical-chemical characteristics of thermoplastic barrier films designed for agricultural and horticultural soil disinfection by means of fumigation.
This document specifies also the test methods for verifying these requirements, except the method for determining film permeability using a static technique, which is specified in EN 17098 2.
This document defines the criteria for design for recycling of barrier films and refer to EN 18109 for the product lifecycle, including installation, use, removal and collection for end of life for management of the product after its usage.
This document is applicable to films used during soil disinfection by fumigation (class 1), and to films used during soil disinfection subsequently kept in situ as mulch films (class 2).
On the date of publication of this document, the barrier films are multi-layer films.

This document provides characteristics and typical values for poly(ethylene terephthalate) (PET) recyclates intended for groups of defined applications (the product families).
The characteristics and typical values for the different product families are derived from the performance requirements of the products belonging to that family, including requirements for product manufacturing processes where applicable.
This document applies to plastic recyclates intended to be used for the manufacturing of (intermediate) products.
This document is intended to be used in conjunction with part 1 of this standard series, which describes the designation system for plastic recyclates. The designation system allows comparison between recycled and virgin material at the level of the polymer's defined designatory properties.
NOTE 1   Examples of designations of plastic recyclates are given in the Annex A.
NOTE 2   The selection of properties for a product family is based on EN ISO 10350 1, extended with specific properties related to plastic recyclates.

This document specifies an analysing methodology for protecting potable water in potable water installations within and outside buildings but within premises from the risk of pollution by backflow of non-potable water and gives recommendations on the design, risk analysis, backflow prevention devices and their installation methods (see Figure 1 and Figure 2).
This methodology is also intended to be used outside premises for all water systems connected to a potable water distribution system up to and including the point of use (see Figure 3).
The product standards for the specific backflow prevention devices or arrangements are intended to be used in conjunction with this document. For the development of new devices or systems, this document is intended to be used as a reference to establish the necessary level of backflow protection.

IEC 60270:2025 is applicable to the charge-based measurement of partial discharges which occur in electrical apparatus, components or systems when tested with alternating voltages (AC) up to 500 Hz or with direct voltage (DC).
This document:
– defines the terms used;
– defines the quantities to be measured;
– describes the measurement frequencies as well as the test and measuring circuits which may be used;
– defines analogue and digital measuring methods required for common applications;
– specifies methods for calibration and requirements of instruments used for calibration;
– gives guidance on test procedures;
– gives some assistance concerning the discrimination of partial discharges from external interference.
The provisions of this document are used in the drafting of specifications relating to partial discharge measurements for specific power apparatus. It deals with electrical measurements of impulsive (short-duration) partial discharges, but reference is also made to non-electrical methods primarily used for partial discharge location (see Annex F). Diagnosis of the behaviour of specific power apparatus can be aided by digital processing of partial discharge data (see Annex E) and also by non-electrical methods that are primarily used for partial discharge location (see Annex F).
This document is primarily concerned with electrical measurement of partial discharge in terms of apparent charge for specific power apparatus made during tests with alternating voltage, but specific problems which arise when tests are made with direct voltage are considered in Clause 11.
The terminology, definitions, basic test circuits and procedures often also apply to tests at other frequencies, but special test procedures and measuring system characteristics which are not considered in this document may be required. For measurements at higher frequency ranges, see IEC TS 62478.
Annex A provides normative requirements for performance tests on calibrators.
This fourth edition cancels and replaces the third edition published in 2000, and Amendment 1:2015. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) Title modified.
b) Use with alternating voltages up to 500 Hz or with direct voltage.
c) Clear focus on charge-based partial discharge measurements.
d) Streamlined performance checks for partial discharge measurement system components.
e) Improved normative Annex A for performance tests on calibrators.
f) Revised and new informative Annexes.
In a future revision, this document will seek horizontal publication status in accordance with IEC Guide 108.

This European Standard defines terms and specifies the general design characteristics of ladders.
It applies to portable ladders designed for general professional and non-professional use.
This standard does not apply to portable ladders which by their design and instructions are intended and limited only for a specific professional use and as a result are not for general professional or non-professional use."
NOTE 1   For multiple hinge joint ladders EN 131–4 applies.
NOTE 2   For telescopic ladders EN 131–6 applies.
NOTE 3   For mobile ladders with platforms EN 131–7 applies.
NOTE 4   This standard does not apply to step stools for which EN 14183 applies.
NOTE 5   For ladders to work near high voltage installations, EN 61478 applies and for working near low voltage electric installations, EN 50528 applies.

Scope of ISO 5149-4:2022:
This document specifies requirements for safety and environmental aspects in relation to operation,  maintenance and repair of refrigerating systems and the recovery, reuse and disposal of all types of refrigerant, refrigerant oil, heat transfer fluid, refrigerating system and part thereof.
This  document  does  not  cover  "motor  vehicle  air  conditioners"  constructed  according  to  the  product  standards such as ISO 13043.
These requirements are intended to minimize risks of injury to persons and damage to property and the environment resulting from improper handling of the refrigerants or from contaminants leading to system breakdown and resultant emission of the refrigerant.

IEC 60350-2:2025 defines methods for measuring the performance of electric hobs for household use. Appliances covered by this document can be built-in or designed to be placed on a work surface. The hob can be part of a cooking range and it can have an integrated cooking fume extractor, i.e. a hob with down-draft system . This document defines the main performance characteristics of hobs which are of interest to the user and specifies methods for measuring these characteristics. This document does not specify a classification or ranking for performance. Some of the tests which are specified in this document are not considered to be reproducible since the results can vary between laboratories. They are therefore intended for comparative testing purposes only. This document does not deal with safety requirements (IEC 60335-2-6 and IEC 60335-2-9). This document is also applicable for portable appliances with similar functionality. This third edition cancels and replaces the second edition published in 2017 and Amendment 1:2021. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) new definitions for portable hob, hob with down-draft system and low power modes are amended in Clause 3;
b) revision of Clause 5: Tolerance for water amount added, requirements for dimension measurement added;
c) removal of 6.4 Level of solid hotplates;
d) revision of Clause 7 in order to improve the application of the smoothing average;
e) revision of Table 1 and Table 3 in order to amend missing tolerances:
f) Ry replaced by L* in Clause 9 and reference to IEC TS 63350;
g) requirements for digital assessment in 9.1.6 removed as they are covered in IEC TS 63350;
h) revision of Clause 12 Power measurement of low power modes;
i) removal of Clause 13 Spillage capacity of hobs;
j) Annex G Low-power mode measurements added;
k) removal of Annex D 'Shade chart' as the shade charts are specified in IEC TS 63350;
l) removal of Annex E 'Data and calculation sheet' as the calculation sheet is substituted by a
supporting document located on the IEC web site;
m) update of former Annex F 'Addresses of suppliers' by removal of former Clause F.6, F.7 and F.8 and by adding a further possible supplier in new D.4

This document describes steps, conditions and protocols for safe maintenance and repair to facilitate remanufacturing, re-use and preparation for repurposing of battery systems, battery packs and battery modules designed for EV applications for alkali-ion (Li-ion, Na-ion), Pb, NiMH and combined chemistries.
This document also includes an informative guidance on design and assembly techniques that facilitate the maintenance, repair, re-use and preparation for repurposing of EV battery systems, battery packs and battery modules (Annex B).
NOTE   Individual cell is replaced when it is allowed and described by the EV battery systems, battery packs and battery modules manufacturer. In this case, battery modules manufacturer provides the necessary instructions for cell replacement.

IEC 61987-41: 2025 provides:
• a characterization for the integration of process analysers in the Common Data Dictionary (CDD),
• generic structures for operating lists of properties (OLOP) and device lists of properties (DLOP) of measuring equipment in conformance with IEC 61987-10,
• generic structures for Dynamic Data, e.g. for condition monitoring of process analysers.
The generic structures for the OLOP and DLOP contain the most important blocks for process analysers. Blocks pertaining to a specific equipment type will be described in the corresponding part of the IEC 61987 standard series. Similarly, equipment properties are not part of this document. Thus, OLOP, DLOPs and LOPDs for selected process analysers families will be found in the IEC CDD.

This document applies to high pressure die casting machines:
a)       hot-chamber die casting machines (horizontal die closing system);
b)       horizontal cold-chamber die casting machines (horizontal die closing system).
This document applies to high pressure die casting units, i.e. high pressure die casting machines (HPDCM), and their interfaces with the following ancillary equipment:
a)       die;
b)       melting, holding and dosing furnaces (see ISO 13577-1:2016);
c)        metal feeding equipment;
d)       inserting and removal devices;
e)       spraying appliances;
f)         heating and cooling devices for the die.
This ancillary equipment itself is not covered.
Additional risks arising from the material being cast are not covered.
This document does not apply to either low pressure die casting machines or gravity die casting machines, or both.
This document deals with all significant hazards, hazardous situations and events relevant to pressure die casting machines when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4).
This includes hazards coming from intentional interactions as well as unintentional but foreseeable interactions between movable parts of the machine and persons.
This document provides the requirements to be met by the manufacturer to ensure the safety of persons and property during transport, commissioning, use, de-commissioning and maintenance periods, as well as in the event of foreseeable failures or malfunctions that can occur in the equipment.

This document is the general part of the series that describes the designation system for plastic recyclates.
This document is dealing with recyclates after the recycling operation and prior to converting and compounding (when applicable). It is dealing with preparation of samples and determination of properties.
NOTE 1   This document supports the underlaying standards of this series that, per polymer type, provide an overview of the relevant characteristics and typical values for recyclates for use in certain application groups (product families) in combination with the relevant converting technologies.
NOTE 2   The overview of the relevant properties is based on and further extends the relevant properties given in EN ISO 10350 1.

This document applies to hot rolled and cold rolled non-coated steel flat products made of multiphase steels for cold forming. It covers cold rolled products of thicknesses t < 3 mm and hot rolled products of thicknesses t ≤ 6,5 mm.
These products are delivered in sheet, hot rolled strip, slit hot rolled strip, cold strip, slit cold rolled strip or cut lengths obtained from slit wide strip.
Flat products of multiphase steels for cold forming can be delivered with an electrolytic zinc coating according to EN 10152.

This document specifies the physical and mechanical properties of fittings made from unplasticized polyamide (PA-U) in accordance with ISO 16486-1, intended to be buried and used for the supply of gaseous fuels.
It also specifies the test parameters for the test methods to which it refers.
The ISO 16486 series is applicable to PA-U piping systems, the components of which are connected by fusion jointing and/or mechanical jointing.
In particular, this document lays down dimensional characteristics and requirements for the marking of fittings.
In conjunction with the other parts of the ISO 16486 series, this document is applicable to PA-U fittings, their joints, joints with components of PA-U and joints with mechanical fittings of other materials, and to the following fitting types:
—     fusion fittings (electrofusion fittings and butt fusion fittings), and
—     transition fittings.

This part of IEC 60204 applies to electrical, electronic, programmable electronic equipment and systems to hoisting machines and related equipment, including a group of hoisting machines working together in a co-ordinated manner
NOTE 1 In this part of IEC 60204, the term "electrical" includes both electrical and electronic matters (i.e. "electrical equipment" means both the electrical, electronic and programmable electronic equipment).
NOTE 2 In the context of this part of IEC 60204, the term “person” refers to any individual and includes those persons who are assigned and instructed by the user or user’s agent(s) in the use and care of the hoisting machine in question.
The equipment covered by this part of IEC 60204 commences at the point of connection of the supply to the electrical equipment of the hoisting machine (crane-supply-switch) and includes systems for power supply and control feeders situated outside of the hoisting machine, for example, flexible cables or conductor wires or conductor bars (see Figure 3).
NOTE 3 The requirements for the electrical supply installation of electrical equipment of a hoisting machine are given in IEC 60364.
This standard is applicable to equipment or parts of equipment not exceeding 1 000 V AC or 1 500 V DC between lines and with nominal frequencies not exceeding 200 Hz.
NOTE 4 Special requirements for electrical equipment of hoisting machines intended to be operated at higher voltages, see IEC 60204-11 (Annex D)
This part of IEC60204 does not cover all the requirements (for example guarding, interlocking, or control) that are needed or required by other standards or regulations in order to protect persons from hazards other than electrical hazards. Each type of hoisting machine has unique requirements to be accommodated to provide adequate safety. This part of 60204 doesn´t cover noise risks and vibration risks.
Additional and special requirements can apply to the electrical equipment of hoisting machines including those that
- handle or transport potentially explosive material (e.g. paint or sawdust);
- are intended for use in potentially explosive and/or flammable atmospheres;
- have special risks when transporting or moving certain materials
- are intended for use in mines.
For the purposes of this standard, hoisting machines include cranes of all types, winches of all types and storage and retrieval machines. The following product groups are included:
- overhead travelling cranes;
- mobile cranes;
- tower cranes;
- slewing luffing cranes;
- gantry cranes;
- offshore cranes;
- floating cranes;
- winches of all types;
- hoists and accessories;
- loader cranes;
- cable cranes;
- load holding devices;
- storage and retrieval machines;
- monorail hoists;
- straddle carriers;
- rubber tyred gantry cranes (RTGs).
NOTE 5 Definition of the different crane types see ISO 4306-1
This standard does not cover individual items of electrical equipment other than their selection for use and their erection.

IEC 63270-1:2025 provides guidance on the functional structure model, procedure, method, interface of function blocks. It also offers guidance on data requirements for predictive maintenance of equipment, devices and systems for industrial automation applications.
Condition monitoring is not only within the scope of this document but can also be an important input for predictive maintenance.

This document provides characteristics and typical values for poly(vinyl chloride) (PVC) recyclates intended for groups of defined applications (the product families).
The characteristics and typical values for the different product families are derived from the performance requirements of the products belonging to that family, including requirements for product manufacturing processes where applicable.
This document applies to plastic recyclates intended to be used for the manufacturing of (intermediate) products.
This document is intended to be used in conjunction with part 1 of this standard series, which describes the designation system for plastic recyclates. The designation system allows comparison between recycled and virgin material at the level of the polymer’s defined designatory properties.
NOTE 1   Examples of designations of plastic recyclates are given in Annex A.
NOTE 2   The selection of properties for a product family is based on EN ISO 10350 1, extended with specific properties related to plastic recyclates.

IEC 60749-34-1:2025 describes a test method that is used to determine the capability of power semiconductor modules to withstand thermal and mechanical stress resulting from cycling the power dissipation of the internal semiconductors and the internal connectors. It is based on IEC 60749-34, but is developed specifically for power semiconductor module products, including insulated-gate bipolar transistor (IGBT), metal-oxide-semiconductor field-effect transistor (MOSFET), diode and thyristor.
If there is a customer request for an individual use or an application specific guideline (for example ECPE Guideline AQG 324), details of the test method can be based on these requirements if they deviate from the content of this document.
This test caused wear-out and is considered destructive.

This document specifies test methods and acceptance criteria, within the frequency range of 0,5 MHz to 15 MHz, for assessing the performance of equipment dedicated for determining thickness using pulse-echo ultrasound, e.g. according to ISO 16809.
This document only specifies the verifications required for the determination of thickness.
This document is applicable to instruments with numerical display and instruments with A-scan presentation, each using either single- or dual-transducer probes.
The tests described in this document can be used for verifying equipment covered by ISO 22232-1 and ISO 22232-2 when used for thickness determination.

This document specifies requirements for the safety, strength and durability of all types of non-domestic seating intended to be used by adults with a weight of not more than 110 kg, including office visitor chairs.
This document does not apply to ranked seating, office work chairs, chairs for educational institutions, outdoor seating and to links for linked seating for which other European Standards exist. It does also not apply to work chairs for industrial use.
This document does not include requirements for the durability of upholstery materials, castors, reclining and tilting mechanisms and seat height adjustment mechanisms.
This document does not include requirements for the resistance to ageing, degradation and flammability.
This document does not include requirements for electrical safety.
Annex A (normative) contains test methods for finger entrapment and shear and compression.
Annex B (normative) contains a seat side-to-side durability test at D-G points.
Annex C (normative) contains a test method for Leg rest durability.
Annex D (normative) contains the determination of seat loading point for seating with suspended flexible material.
Annex E (informative) contains additional drop tests.
Annex F (informative) contains information on the level of test severity in relation to applications.
Annex G (informative) contains recommended dimensions for non-domestic chairs.
Annex H (informative) contains a rationale for single column seating.

This document provides characteristics and typical values for polystyrene (PS) recyclates intended for groups of defined applications (the product families).
The characteristics and typical values for the different product families are derived from the performance requirements of the products belonging to that family, including requirements for product manufacturing processes where applicable.
This document applies to plastic recyclates intended to be used for the manufacturing of (intermediate) products.
This document is intended to be used in conjunction with part 1 of this standard series, which describes the designation system for plastic recyclates. The designation system allows comparison between recycled and virgin material at the level of the polymer’s defined designatory properties.
NOTE 1   Examples of designations of plastic recyclates are given in Annex A.
NOTE 2   The selection of relevant properties for a product family is based on EN ISO 10350 1, extended with specific properties related to plastic recyclates.

This document deals with the technical requirements and the means for their verification for additive manufacturing (AM) machines using a bed of metallic powder, pyrophoric feedstock excluded, and a laser herein designated as machine.
This document deals with all significant hazards, hazardous situations or hazardous events during all phases of the life of the machine (ISO 12100:2010, 5.4), as listed in Annex A, caused by AM machines using a bed of metallic powder and a laser when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.
This document does not deal with hazards which can occur:
—     during the design and construction phase of the laser beam powder ped fusion (PBF-LB) machine itself;
—     operating in potentially explosive atmospheres.
This document does not apply to technologies other than AM metals PBF-LB.
This document is not applicable to machines manufactured before the date of its publication.

This document provides characteristics and typical values for polypropylene (PP) recyclates intended for groups of defined applications (the product families).
The characteristics and typical values for the different product families are derived from the performance requirements of the products belonging to that family, including requirements for product manufacturing processes where applicable.
This document applies to plastic recyclates intended to be used for the manufacturing of (intermediate) products.
This document is intended to be used in conjunction with part 1 of this standard series, which describes the designation system for plastic recyclates. The designation system allows comparison between recycled and virgin material at the level of the polymer’s defined designatory properties.
NOTE 1   Examples of designations of plastic recyclates are given in Annex A.
NOTE 2   The selection of properties for a product family is based on EN ISO 10350 1, extended with specific properties related to plastic recyclates.

This document provides characteristics and typical values for polyethylene (PE) recyclates intended for groups of defined applications (the product families).
The characteristics and typical values for the different product families are derived from the performance requirements of the products belonging to that family, including requirements for product manufacturing processes where applicable.
This document applies to plastic recyclates intended to be used for the manufacturing of (intermediate) products.
This document is intended to be used in conjunction with part 1 of this standard series, which describes the designation system for plastic recyclates. The designation system allows comparison between recycled and virgin material at the level of the polymer's defined designatory properties.
NOTE 1   Examples of designations of plastic recyclates are given in Annex A.
NOTE 2   The selection of properties for a product family is based on EN ISO 10350 1, extended with specific properties related to plastic recyclates.

This document specifies a test method for comparing the compression shear strength of adhesive bonds in wood and solid wood after exposure to a target temperature for a specified duration of time.
This document is applicable to adhesives used in load bearing timber structures.
This document is not applicable to Epoxy- and two component Polyurethane-adhesives.
This method is intended to obtain data for the performance of wood adhesives at very high temperatures. The result of this comparison can be used to classify the adhesive with regard to the behaviour of load-bearing timber structures in fire.

This document provides characteristics and typical values for acrylonitrile-butadiene-styrene (ABS) recyclates intended for groups of defined applications (the product families).
The characteristics and typical values for the different product families are derived from the performance requirements of the products belonging to that family, including requirements for product manufacturing processes where applicable.
This document applies to plastic recyclates intended to be used for the manufacturing of (intermediate) products.
This document is intended to be used in conjunction with part 1 of this standard series, which describes the designation system for plastic recyclates. The designation system allows comparison between recycled and virgin material at the level of the polymer’s defined designatory properties.
NOTE 1   Examples of designations of plastic recyclates are given in Annex A.
NOTE 2   The selection of properties for a product family is based on EN ISO 10350 1, extended with specific properties related to plastic recyclates.

IEC 63522-2:2025 This part is used for testing all kinds of electrical relays and for evaluating their ability to perform under expected conditions of transportation, storage and all aspects of operational use. This document defines a standard test method to ensure that particular mechanical properties (such as contact force, armature travel, contact gaps) and weight, are within specified limits.

This document specifies methods for the determination of components in plastics that can be extracted by hot organic liquids near their boiling points. It also specifies a special extraction method called cold-extraction.
The extractable components can be monomers, oligomers, polymers, plasticizers, stabilizers, etc. The kind and percentage of extractable matter influence the properties of plastics.
This document does not apply to plastics that come into contact with food or drinking water, because special regulations for those plastics are established in many countries. The methods of this document are not intended to be used for migration tests.
If this document is used to test plastics other than those mentioned in Table 1, the operating conditions are intended to be agreed upon by the interested parties.

This document specifies a test method for determining the mechanical viscoelastic properties of interlayer materials. The interlayers under examination are those used in the production of laminated glass or laminated safety glass. The shear characteristics of interlayers are needed to design laminated glass in accordance with EN 16612:2019 and EN 19100 (all parts).
Parameters of the Prony series, widely used in numerical simulation, can be derived from the measurements in Annex C.

The present document specifies the abstract syntax of the Test Description Language (TDL) in the form of a meta-model based on the OMG ® Meta Object Facility™ (MOF) [1]. It also specifies the semantics of the individual elements of the TDL meta-model. The intended use of the present document is to serve as the basis for the development of TDL concrete syntaxes aimed at TDL users and to enable TDL tools such as documentation generators, specification analysers and code generators.
The specification of concrete syntaxes for TDL is outside the scope of the present document. However, for illustrative purposes, an example of a possible textual syntax together with its application on some existing ETSI test descriptions are provided.
NOTE: OMG®, UML ®, OCL™ and UTP™ are the trademarks of OMG (Object Management Group). This
information is given for the convenience of users of the present document and does not constitute an
endorsement by ETSI of the products named

This document is applicable to lead-acid batteries with a nominal voltage of 12 V, used primarily as power source for the starting of internal combustion engines (ICE), lighting and also for auxiliary equipment of ICE vehicles. These batteries are commonly called "starter batteries". Batteries with a nominal voltage of 6 V are also included in the scope of this document. All referenced voltages need to be divided by two for 6 V batteries. The batteries under the scope of this document are used for micro-cycle applications in vehicles which can also be called Start-Stop (or Stop-Start, idling-stop system, micro-hybrid or idle-stop-and-go) applications. In cars with this special capability, the internal combustion engine is switched off during a complete vehicle stop, during idling with low speed or during idling without the need of supporting the vehicle movement by the internal combustion engine. During the phases in which the engine is switched off, most of the electric and electronic components of the car need to be supplied by the battery without support of the alternator. In addition, in most cases an additional regenerative braking (recuperation or regeneration of braking energy) function is installed. The batteries under these applications are stressed in a completely different way compared to classical starter batteries. Aside of these additional properties, those batteries need to crank the ICE and support the lighting and also auxiliary functions in a standard operating mode with support of the alternator when the internal combustion engine is switched on. All batteries under this scope need to fulfil basic functions, which are tested under application of EN 50342 1:2015.
This document is applicable to batteries for the following purposes:
-   Lead-acid batteries of the dimensions according to EN 50342 2 for vehicles with the capability to automatically switch off the ICE during vehicle operation either in standstill or moving (“Start-Stop”);
-   Lead-acid batteries of the dimensions according to EN 50342 2 for vehicles with Start-Stop applications with the capability to recover braking energy or energy from other sources.
This document is not applicable to batteries for purposes other than mentioned above, but it is applicable to EFB delivered in dry-charged conditions according to EN 50342 1:2015, Clause 7.
NOTE   The applicability of this document also for batteries according to EN 50342 4 is under consideration.

This document gives guidelines for the choice of non-destructive testing (NDT) methods for welds in metals and for the evaluation of the results for quality control purposes, based on quality requirements, material, weld thickness, welding process and extent of testing.
This document also specifies general rules and standards to be applied to the different types of testing, for the selection of the method, the techniques and the acceptance levels.
Acceptance levels cannot be a direct interpretation of the quality levels defined in ISO 5817 or ISO 10042. They are linked to the overall quality of the produced batch of welds.
The requirements specified in this document for acceptance levels for NDT conform with quality levels stated in ISO 5817 or ISO 10042 (moderate, intermediate, stringent) only on a general basis and not in detail for each indication.
Annex A gives correlations between quality levels, testing levels and acceptance levels for specific testing techniques.
Annex B gives an overview on specific testing techniques of standards linked to quality levels, acceptance levels and testing methods.

This document specifies the general characteristics of grooved pins, made of steel and stainless steel, with nominal diameters 1 mm to 25 mm.
These grooved pins are designed to fulfil the main following functions, due to the elastic fit behaviour of the grooves:
—     locking of two (or more) parts,
—     positioning or guiding,
—     relative rotation of the assembled parts.

The present document specifies the architecture for the execution environment of TDL test descriptions and functional requirements for the components in the form of function declarations that will be provided by an implementation of the components and data types used as input and output parameters of the functions. The test executor component will interpret the elements of test descriptions according to operational semantics specified in [1]. The present document will be used for developing a code generator or interpreter for mapping abstract TDL constructs to code and the required test environment components that are specific to a chosen test execution platform.