Search Catalog

This document establishes the basic dimensions and the functional and strength requirements of corner and intermediate cast fittings for series 1 freight containers, i.e. containers which conform to ISO 668 and ISO 1496 (all parts), with the exception of air mode containers (see ISO 8323). Recognizing that there are containers which have ratings and dimensions different from ISO Series 1 containers referred to in ISO 668, which can be fitted with corner fitting of the same design as those described in this document, or of another design, special arrangements for certification of any fittings for such containers can be required.

This document specifies the conditions for conducting axial, constant-amplitude, force-controlled, fatigue tests at ambient, elevated, and low temperature on metallic specimens, without deliberately introduced stress concentrations. The object of testing while employing this document is to provide fatigue information, such as the relation between applied stress and number of cycles to failure for a given material condition, such as microstructure, at various stress ratios. While the form, preparation and testing of specimens of circular and rectangular cross-section are described, component testing and other specialized forms of testing are not included in this document. NOTE 1 Fatigue tests on notched specimens are not covered by this document since the shape and size of notched test pieces have not been standardized. However, fatigue-test procedures described in this document can be applied to fatigue tests of such notched specimens. NOTE 2 Throughout this document, the engineering stress is employed. Engineering stress is equal to the axially applied force divided by the cross-sectional area of the test specimen, S = Force/Area, [MPa], at the test temperature.

This document specifies requirements and provides guidance for bodies providing audit and certification of compliance management systems (CMS), in addition to the requirements contained within ISO/IEC 17021-1 [3]. Observance of these requirements is intended to ensure that certification bodies provide audit and certification in a competent, consistent and impartial manner.

This document specifies an implementable, conformance-testable coverage structure based on the abstract schema for coverages defined in the ISO 19123-1 coverage fundamentals. This document defines a concrete data structure that is suitable for encoding in many formats.

This document specifies an accelerated method for the determination of wet-scrub resistance. The determination of cleanability is not covered in the scope of this document. NOTE The ability of coatings to withstand wear caused by repeated cleaning operations is an important consideration both from a practical point of view and when comparing and rating such coatings. Since wet-scrub resistance depends not only on the quality of a coating but also on the substrate, the method of application, the drying conditions and other factors, the results obtained are not directly transferable to actual practice. In this document, the evaluation of the coating is based on a defined substrate, a fixed application method, specified drying conditions and a defined method of wet scrubbing.

This document provides requirements and guidelines for selecting the measuring device, measuring geometry and temperature control unit for tests involving rotational and oscillatory rheometry. The general principles of test performance are described and example evaluations of rotational and oscillatory rheometry are provided.

This document specifies the chemical composition and mechanical properties of magnesium and magnesium alloys for wrought products in the form of bars and solid sections, tubes and hollow sections, forgings and plate and sheet.

This document specifies photometric methods of test for comparing in the visible spectrum: the tinting strength of two similar coloured pigments dispersed in an alkyd resin without a drier; the scattering power of two white pigments of the same type dispersed in an alkyd resin without a drier. This document does not apply to the comparison of coloured pigments that on reduction differ greatly in colour.

This document specifies requirements and provides recommendations for campsite facilities and services, covering the following: campsite layout and design; sanitation and other important facilities; sustainability; inclusivity and accessibility; safety and security. This document aims to ensure that campsite facilities, amenities, services and management practices meet basic safety and environmental requirements, while providing a good quality camping experience for guests. This document applies to campsites in natural or developed areas that are designed and managed to provide pitches for guests using their own camping units (such as tents, leisure accommodation vehicles including caravans, motor caravans or camper vans) and/or static or semi-permanent accommodation units (such as camping houses, mobile homes, rental caravans, safari tents or similar) supplied by the campsite operator. This document applies to campsite owners, operators and regulators.

IEC PAS 61850-90-28:2026, which is a Publicly Available Specification, specifies the expected behavior and associated documentation related to the validation of received GOOSE and SV messages. It considers engineering rules and guidance to ensure that the communication configuration process is well designed for this validation. Conformance statements related to this validation are also considered.
This document considers subscribers claiming conformance to latest editions of the IEC 61850 series in combination with publishers claiming conformance to any previous version and revision of the IEC 61850 series.

This document specifies materials and the general aspects of polyethylene (PE) piping systems in the field of the supply of gaseous fuels. NOTE For the purpose of this document, the term gaseous fuels includes, for example, natural gas, methane, butane, propane, hydrogen, manufactured gas, biogas, and mixtures of these gases. This document also specifies the test parameters for the test methods referred to in this document. In conjunction with ISO 4437-2, ISO 4437-3, ISO 4437-4 and ISO 4437-5, this document is applicable to PE pipes, fittings and valves, their joints, and joints with components of PE and other materials intended to be used under the following conditions: a maximum operating pressure (MOP) up to and including 10 bar1), at a design reference temperature of 20 °C; an operating temperature between −20 °C and 40 °C. For operating temperatures between 20 °C and 40 °C, derating coefficients are specified in ISO 4437-5. The ISO 4437 series covers a range of MOPs and gives requirements concerning colours. It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or regulations and installation practices or codes 1)1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.

This document specifies what climate data from climate projections are and where to find relevant climate data suited for infrastructure climate adaptation and resilience-building needs. This document gives support to both standards users and standards writers (with the emphasis on standards users) whether detailed climate data and information is specified in a standard, such as in a National Annex, or the standard requires the user to determine relevant climate data and information as a separate exercise. This document is relevant to all climate system data. Users of this Technical Report can also find this document helpful in dealing with derived climate system data, e.g. atmospheric pollution, flooding, ground water levels, wave heights. In addition, guidance is provided for designers of cross-border infrastructure systems, for example on the harmonisation of climate data used.
This document is intended for infrastructure owners, designers, operators and maintainers and staff of central/ regional authorities who are responsible for infrastructure within countries that are associated with CEN/CENELEC. Users includes the national standards’ bodies and authorities who will be responsible for the use of climate data in national annexes to standards.
The document does not define or prescribe the broader climate service delivery process, co-production methodologies, or stakeholder engagement practices.

IEC TS 61400‑28-2:2026 addresses the decommissioning and preparation for recycling of wind turbines.
This scope includes all the tasks and on-site considerations of the different process steps, from the beginning of the dismantling phase, material preparation and arrangement, and preparation for shipment to re-using or recycling facilities. Wind turbines in the context of this document include blades, hubs, nacelles, towers, foundations, generators, gearboxes, cables, electrical equipment, transformers, and any other equipment that can be dismantled from wind turbines and not listed before.
The purpose of this document is to define the framework conditions of decommissioning and preparation for recycling of wind turbines, which includes the tasks and considerations of each of the steps of the process. The objective is to provide basic high-level information on the sustainable and efficient decommissioning and dismantling arrangements for wind turbines.
This document can be used by manufacturers, asset owners, governments, operators, recyclers and personnel involved in the decommissioning and preparation for recycling of wind turbines.

This document specifies the characteristics of fusion fittings made from polyethylene (PE) as well as of mechanical fittings for piping systems in the field of the supply of gaseous fuels. NOTE 1 Additional information related to the installation of PE 100-RC systems is given in ISO 4437-1:2026, Annex A. NOTE 2 Additional information about the suitability of PE pipe systems for hydrogen and its admixtures is given in ISO 4437-1:2026, Annex D. It also specifies the test parameters for the test methods referred to in this document. In conjunction with ISO 4437-1, ISO 4437-2, ISO 4437-4 and ISO 4437-5, this document is applicable to PE pipes, fittings and valves, their joints, and joints with components of PE and other materials intended to be used under the following conditions: a maximum operating pressure (MOP) up to and including 10 bar1), at a design reference temperature of 20 °C; an operating temperature between −20 °C and 40 °C. For operating temperatures between 20 °C and 40 °C, derating coefficients are specified in ISO 4437-5. The ISO 4437 series covers a range of MOPs and gives requirements concerning colours. This document is applicable for fittings of the following types: electrofusion socket fittings; electrofusion saddle fittings; spigot end fittings (for butt fusion using heated tools and electrofusion); socket fusion fittings; mechanical fittings. It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or regulations and installation practices or codes. NOTE 3 The fittings can be, for example, in the form of couplers, saddles, equal and reduced tees, reducers, elbows, bends or end caps. NOTE 4 Fabricated fittings are normally not used for gas applications except for larger dimensions or in the absence of other solutions. Guidance can be found in ISO 4427-3:2019, Annex B. 1)1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.

This document provides requirements and recommendations for the provision of professional beauty salon services. These services relate to the delivery of beauty treatments regardless of where the service is delivered.
This document provides requirements and recommendations for the delivery of beauty treatments performed by a suitably qualified beauty therapist. Recommendations are provided for client management to ensure client safety during any beauty treatments. The delivery of beauty salon services is limited to the boundaries of the qualification of the individual beauty therapists obtained through a recognized education provider.
Medical procedures including aesthetic surgical procedures and cosmetic injectable procedures including sclerotherapy are excluded from the scope of this document.
Hairdressing, barbering and body art tattooing services are also excluded from the scope of this document.

This document establishes a digital ledger technology (DLT) agnostic, decentralized identifier (DID) framework for representing physical assets using tokens. This includes: A DID generation method: An algorithmic data method for generating DIDs from assets with immutable unique identifiers, e.g. serial numbers. A cryptographic method to tie asset data objects to the DID: An algorithmic hash tree data method for transferring a set of asset data objects that are cryptographically tied together, agnostic to any specific DLT or blockchain system. A DID method scheme: A DID method scheme to enable DID registry interoperability, so the digital representation can be stored, resolved or transferred to any compliant DID registry. Real world trust anchor processes: Processes for utilizing off-chain trust anchors to establish proof of real-world human and machine generated events and information that tie a real-world asset to its digital representation.

This document specifies requirements for epoxy powders and texturing surface treatment material for use in preparing fusion-bonded epoxy-coated steel reinforcing bar, wire and welded fabric. It also includes requirements for sealing material used to repair damaged areas and cut ends on reinforcing steel. This document defines a flexible (type A) coating and a nonflexible (type B) coating. The adhesion and moisture resistance of fusion-bonded epoxy powder coatings can be enhanced by certain formulation designs. These coating enhancements typically result in a reduction of the coating’s flexibility.

To facilitate interoperability in a shared industrial environment, this document specifies the requirements for communication between two or more of the following: industrial mobile robot (IMR); IMR fleet manager (IMRFM); other machines, equipment, and applications in the shared industrial environment (e.g. machines tended by the IMRs; enterprise resource planning (ERP) tools; and building infrastructure such as lifts, alarm systems, automated doors). For the purposes of this document, “industrial environment” describes a workplace where the people are working-age adults and the public is restricted from access or not reasonably expected to be present. Further, “industrial” pertains to the production of goods and related services (e.g. manufacturing, laboratory, pharmaceutical, warehousing, distribution, logistics and other workplaces). The following applications are excluded from the scope of this document: entertainment, consumer, military, medical and use on public roads. This document is not safety-related; there are no safety requirements. Navigation requirements are excluded from the scope of this document.

This document specifies the characteristics of pipes made from polyethylene (PE) for piping systems in the field of the supply of gaseous fuels. NOTE 1 Additional information related to the installation of PE 100-RC systems is given in ISO 4437-1:2026, Annex A. NOTE 2 Additional information about the suitability of PE pipe systems for hydrogen and its admixtures is given in ISO 4437-1:2026, Annex D. It also specifies the test parameters for the test methods referred to in this document. In conjunction with ISO 4437-1, ISO 4437-3, ISO 4437-4 and ISO 4437-5, this document is applicable to PE pipes, fittings and valves, their joints, and joints with components of PE and other materials intended to be used under the following conditions: a maximum operating pressure (MOP) up to and including 10 bar1), at a design reference temperature of 20 °C; an operating temperature between −20 °C and 40 °C. For operating temperatures between 20 °C and 40 °C, derating coefficients are specified in ISO 4437-5. The ISO 4437 series covers a range of MOPs and gives requirements concerning colours. This document is applicable to three types of pipe: PE pipes (outside diameter, dn) including any identification stripes; PE pipes with co-extruded layers on either or both the outside and/or inside of the pipe (total outside diameter, dn) as specified in Annex A, where all PE layers have the same MRS rating; PE pipes (outside diameter, dn) with a peelable and contiguous thermoplastics additional layer on the outside of the pipe ("coated pipe") as specified in Annex B. It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or regulations and installation practices or codes. 1)1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.

This document specifies the integrated management of agricultural plastic products with agronomic performance.
This document gives guidance and requirements for their installation, use, removal, sorting, collection and preparation for recycling as well as general guidelines for design for recycling.
NOTE 1   EN 13206:2025, EN 13207:2025, EN 13655:2025, EN 14932:2025 and EN 17098-1:2025 include a specific clause dedicated to design for recycling.
NOTE 2   Design for recycling for products not covered by a standard is detailed in this document.
This document first aims professional users and can be used also for domestic purposes.
This document is applicable to:
-   covering films that comply with EN 13206:2025 or with specifications laid out by the film manufacturer/supplier, used for covering greenhouses, small tunnels or livestock buildings, as well as to direct crop covers used for semi-forcing plants and seed;
-   silage films for horizontal silos that comply with EN 13207:2025 or with specifications laid out by the film manufacturer/supplier;
-   sheaths for horizontal silos (forage crop and grain storage) that comply with EN 13207:2025 or with specifications laid out by the sheath manufacturer/supplier;
-   stretch films for wrapping bales that comply with EN 14932:2025 or with specifications laid out by the film manufacturer/supplier;
-   thermoplastic mulching films that comply with EN 13655:2025 or with specifications laid out by the film manufacturer/supplier;
-   barrier films for agricultural and horticultural soil disinfection by fumigation that comply with EN 17098-1:2025;
-   nets and twines for catling and horticulture that comply with the specifications laid out by EN ISO 4167 or by the manufacturer/supplier;
-   flexible ducts, semi-rigid and rigid pipes and fittings for irrigation that comply with ISO 8779, EN ISO 9261, ISO 13460-1, ISO 16438, EN 14267, EN 12324-2, EN 13635, EN 13997, EN 17176-2:2019+A1:2022 or with specifications laid out by the manufacturer/supplier;
-   fabrics and non-woven nets and sheets for catling and horticulture that comply with ISO 9073 series or with specifications laid out by the manufacturer/supplier.
This document does not cover construction, packaging and food-contact products.
NOTE 3   For products non-suitable for recycling in the context of this document, specific procedures apply.

This document specifies requirements for roofing and cladding products used for assembly into coverings for wall claddings, linings and pitched roofs, made from aluminium sheet with or without additional surface treatment (organic coating or anodising).
This document establishes the general characteristics, the definitions and the labelling of the products, together with requirements for the materials from which the products can be manufactured. It is intended to be used either by manufacturers to ensure that their products comply with the requirements or by purchasers to verify that the products comply before they are despatched from the factory. This document specifies the requirements for products which enable them to meet all normal service conditions. Products can be prefabricated or semi-formed products as well as strip, coil and sheet for on-site-formed applications (e.g. standing seam roofs).
This document is applicable to all discontinuously laid and fully supported roofing and cladding products made of aluminium sheets.
This document does not specify requirements for supporting construction, design of roof system and execution of connections and flashings.
This document does not apply to self-supporting aluminium sheets that are covered by EN 508 2.

Common modification to EN IEC 61851-23 Ed.2 (63680): make Annex BB "informative" instead of "normative"

This document addresses security threats and compromises specific to artificial intelligence (AI) systems. This document aims to provide information to organizations to help them better understand the consequences of security threats specific to AI systems, throughout their life cycle, and descriptions of how to detect and mitigate such threats. This document is applicable to all types and sizes of organizations, including public and private companies, government entities and not-for-profit organizations that develop or use AI systems.

This document specifies a method to measure the total unsaturation of polyether polyols used in the production of polyurethanes by a Raman spectrometric method. It is not applicable to unsaturated compounds that are conjugated with a carbonyl group, a carboxyl group, or a nitrile group.

This Guide defines the role and assists PDs and their Alternates in fulfilling their responsibilities towards the CEN and/or CENELEC Technical Boards (BT).

This part of IEC 61076-2 covers shielded and unshielded, free and fixed circular connectors without breaking capacity (COC) for power, signal and data transmission, and specifies the common dimensions, mechanical, electrical and transmission characteristics and environmental requirements as well as test specifications, respectively.
NOTE 1 As all the connectors described in this document are equipped with shielded data transmission portions, the attribute “shielded” or “unshielded” refers to the additional presence or lack of a shielded connector body.
The connectors described in this document are equipped with an M12, M17, M23 or M40 screw-locking mechanism or a quick-locking mechanism with a size derived from those.
Fixed and rewirable connectors with male or female contacts, mateable with Mxx screw- or quick-locking plugs.
This document provides multiple mating interfaces each of which is associated with a coding preventing the mating of incompatible male and female connectors. The individual codings differ by their numbers of ways, pin layouts and thicknesses, and thus by their power and data transmission capabilities. These codings are referred to as “Type x” where ‘x’ represents an Arabic number.
The connectors described in this document are intended to be used in one-cable automation applications which require various combinations and levels of power up to 600 V AC/ DC and up to 70 A, and either signal or data transmission, or both, with frequencies up to 600 MHz.
NOTE 2 The requirements (or information) described in this document facilitate data transmission through the following Ethernet media systems as defined in IEEE 802.3:
– single-pair Ethernet (10BASE-T1, 100BASE-T1, 1000BASE-T1);
– Fast Ethernet (100BASE-TX);
– Gigabit Ethernet (1000BASE-T);
– 10-gigabit Ethernet (10GBASE-T).

This document aims to provide a procedure for reporting indoor air quality when combusting moxibustion devices. It is intended for use in business-to-business (B to B) transactions, subject to mutual agreement between parties. This document specifies the steps for preparing reports that compare indoor concentration values of target pollutants generated when combusting moxibustion device with international, regional, or national ambient and indoor air quality regulations, standards, or guideline values. This document does not apply to moxibustion devices that do not involve combustion of moxibustion material, such as electric heating moxibustion equipment covered in ISO 21292:2020 and infrared moxibustion-like instruments covered in ISO 20493:2018.

This document specifies requirements and gives recommendations for the qualification and design, installation, testing and integrity management for the external application of composite repair systems to corroded or damaged piping and pipelines, tanks and vessels.

The present document specifies technical characteristic and methods of measurements for Very Small Aperture Terminal (VSAT) equipment which has the following characteristics:
• the VSAT is operating in one or more frequency ranges within the following bands allocated to the Fixed
Satellite Service (FSS), shared with other services, e.g. the Fixed Service (FS) and the Mobile Service (MS):
- 5,850 GHz to 7,075 GHz (Earth-to-space);
- 3,400 GHz to 4,200 GHz (space-to-Earth);
- 4,500 GHz to 4,800 GHz (space-to-Earth);
• the VSAT uses linear or circular polarization;
• the VSAT operates through a geostationary satellite at least 2° away from any other geostationary satellite operating in the same frequency band and covering the same area;
• the VSAT antenna diameter does not exceed 7,3 m, or equivalent effective area;
• the VSAT is either:
- a transmit-only VSAT: designed for transmission-only of radio-communications signals in the frequency band (earth-to-space) specified in the present clause; or
- a transmit-and-receive VSAT: designed for transmission-and-reception of radio-communications signals in the frequency bands specified in the present clause; or
- a receive-only VSAT: designed for reception-only of radio-communications signals in the frequency band (space-to-Earth) specified in the present clause;
• the VSAT is designed for unattended operation;
• the VSAT is operating as part of a satellite network (e.g. star, mesh or point-to-point) used for the distribution and/or exchange of information between users; the VSAT is controlled, and monitored for the transmit functionality, by a Centralized Control and Monitoring Facility (CCMF). The VSAT has to implement Control and Monitoring Functions with either Class A or Class B (structures of the radio states). The specifications associated to the CCMF facility are outside the scope of the present document. The present document applies to the VSAT with its ancillary equipment and its various terrestrial ports, and when operated within the boundary limits of the operational environmental profile defined for the intended use of the VSAT including all equipment as brought to the market. The present document does not contain any requirement, recommendation or information about the installation of the VSAT. All parts of the indoor unit related to reception, processing and presentation of the received information except the control channel are not within the scope of the present document. The syntax of the control channel messages is outside the scope of the present document. The present document is intended to cover the provisions of Directive 2014/53/EU (Radio Equipment Directive) [i.5] article 3.2. NOTE: The relationship between the present document and essential requirements of article 3.2 of
Directive 2014/53/EU [i.5] is given in annex A.

This test method defines test terms and specifies a standard method for evaluating the homogeneity of electrically conductive spread carbon fibre tow using eddy current measurement. The impedance in the width direction of the fibre is measured continuously, and the standard deviation of the measured impedance determines the homogeneity of the conductive material in fibre form.

IEC 62475:2026 is applicable to high-current testing and measurements on both high-voltage and low-voltage equipment. It deals with steady-state and short-time direct current (as e.g. encountered in high-power DC testing), steady-state and short-time alternating current (as e.g. encountered in high-power AC testing), and impulse-current. In general, currents above 100 A are considered in this International Standard, although currents less than this can occur in tests.
This standard:
• defines the terms used;
• defines parameters and their tolerances;
• describes methods to estimate uncertainties of high-current measurements;
• states the requirements applicable to a complete measuring system;
• describes the methods for approving a measuring system and checking its components;
• describes the procedure by which the user shows that a measuring system meets the requirements of this document, including limits set for uncertainty of measurement.
This standard also covers fault detection during, for example, lightning impulse testing.
This second edition cancels and replaces the first edition published in 2010. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
• minor errors in edition 1 have corrected;
• terms and definitions have been modified to achieve best possible adherence to IEC 60060‑2:2025 and have been ascribed appropriate [SOURCE];
• terms and definitions which in edition 1 were presented in clauses other than Clause 3 have been moved into Clause 3.
• Annex B, Clause B.4 has been amended to provide an example of uncertainty calculation for the use of an approved measuring system;
• Clause C.2 has been deleted since the definitions given there are not referred to, with the exception of the origin of the step, which is used in Annex D. The applicable information has been added to Annex D as Note 1.
• Annex G, Clause G.8 has been amended to replace “peak factor” by “a factor”. Texts have been clarified. Equations for relation between factor κ and cos ϕ have been developed to a simplified form.
• Annex G, Clause G.9 has been added.

This document applies to all high-voltage direct current (HVDC) converter stations with linecommutated converters (LCC) as well with voltage-sourced converters (VSC) used for power exchange (power transmission or back-to-back installation) in utility systems. For linecommutated converters (LCC), this document presumes the use of 12-pulse thyristor converters but can, with due care, also be used for 6-pulse thyristor converters.
Where VSC is referred to in this document, it is assumed to be of the MMC-type or similar, with very low harmonic generation. It is important to treat other types of VSC as appropriate.
In some applications, synchronous compensators, static var compensators (SVC), or static synchronous compensator (STATCOM) are connected to the AC bus of the HVDC converter station. The loss determination procedures for such equipment are not included in this document.
This document presents a set of standard procedures for determining the total losses of an HVDC converter station, except for VSC valves which are covered by the IEC 62751 series.
The procedures cover all parts, except as noted above, and address no-load operation and operating losses together with their methods of calculation which use, wherever possible, measured parameters.
Converter station designs employing novel components or circuit configurations compared to the typical design assumed in this document, or designs equipped with unusual auxiliary circuits that can affect the losses, are assessed on their own merits.

IEC 63497:2026, which is a product standard, is intended to specify the EMC, performance and safety requirements of shunt-connected active correction devices (ACD) with rated system voltages not exceeding 1 000 V AC or 1 500 V DC.
These devices can be either cord or permanently connected. They can be movable, stationary, or fixed devices.
An ACD includes both a static VAR generator (SVG) and an active harmonic filter (AHF).
The primary function of a shunt connected ACD is to do one or more of the following:
- active harmonic filtering;
- reactive power compensation;
- unbalanced load compensation.
Additional functions of a shunt-connected ACD, not addressed by this document, can be the following:
- flicker compensation;
- interharmonic component filtering.
In case of hybrid devices, combining a passive harmonic filter and an ACD, this document covers only the active part.
This document does not cover
- active mitigation functions part of another device (variable speed drive, uninterruptible power supply, dynamic voltage restorer, etc.),
- switched power capacitors,
- switched inductors,
- passive harmonic filters,
- energy storage converters, and
- series-connected active correction devices.

This document provides statistical summaries of anthropometric data (body dimensions and physical strength) of children in Europe considering different age groups. The age range covered by this report is up to 15 years.
This document also provides information about:
— date and origin of the data;
— geographic limitations of the data;
— size and sex of the population measured or scanned;
— description of the anthropometric and strength measures.

This document specifies three film-digitisation quality classes for the requirements of non-destructive testing. The user specifies one of these quality classes for the respective film digitisation task. The digitisation parameters depend on the radiation energy, the material thickness penetrated and the quality level of the original radiographic film. This document does not address signal processing, display and storage of the digitised data.
For the application of this document, ISO 14096-1 provides definitions and measurement procedures.

This document describes the principles, equipment, materials, testing procedures, quality control and test reports for determining shale pore structure and mineral content using scanning electron microscopy (SEM) with energy dispersive spectrometer (EDS). This document is applicable to the analysis of pore structure by field emission SEM and mineral content of shale samples by SEM with EDS in shale gas exploration and development.

This document specifies requirements and test methods for the qualification and re-qualification of laser beam machines for metal powder bed fusion additive manufacturing for aerospace applications.
This document can also be applied to non-aerospace applications if this is part of a contract.
It can also be used to verify machine features during periodic inspections or following maintenance and repair activities.

This document specifies the dimensions and tolerances of resistance spot welding electrode adaptors where the fixing element for the cap (see ISO 5821 [2]) is a male taper of 1:10 and for which the electrode taper fits in conformance with ISO 1089 [3] .

This document specifies the general requirements for central power supply systems for an independent energy supply to essential safety equipment. This document covers systems that are permanently connected to AC supply voltages not exceeding 1 000 V and use batteries as an alternative power source.
Central safety power supply systems are intended to ensure energy supply to emergency escape lighting in the event of normal supply failure and could be suitable for energizing other essential safety equipment, for example:
- electric circuits of automatic fire extinguishing installations;
- paging systems and signalling safety installations;
- smoke extraction equipment;
- carbon monoxide warning systems;
- special safety installations related to specific buildings, e.g. high-risk areas.
The power supply of CPS systems is expected to be dedicated only to the essential safety equipment, and not for other type of loads such as general purpose IT or industrial systems etc.
Combinations of the aforementioned safety equipment types can be used together on the same central safety power supply system providing the availability for safety equipment loads is not impaired. A fault occurring in a circuit is expected to not cause the interruption in any other circuit used to supply essential safety equipment.
Schematic representations of typical central safety power supply equipment are depicted in Clause 4.
Power supply systems for fire alarm equipment that are covered by EN 54 (series) are excluded.

This document defines the structure, governance and management of the ISO Geodetic Register, in accordance with ISO 19135. This document also identifies the data elements applicable to geodetic referencing by coordinates, in accordance with ISO 19111.

This document specifies requirements and recommendations for the assessment of the thermal conditions inside a vehicle compartment. It can also be applied to other confined spaces with asymmetric climatic conditions.
It applies to the assessment of thermal conditions, when deviations from thermal neutrality are relatively small.

This document specifies the methods, parameter sets and models to develop and utilize a data package for a part created using AM technologies (AM part). This document is applicable to the information requirements associated with workflow of the fabrication of an AM part, from design to acceptance. Peripheral information related to entities such as organization, facility, operator, security, and others is addressed for sake of completeness; but is not the focus of this document and can be defined elsewhere. This document provides the means to develop an organizational or application-specific data package for the communication between and amongst the designer, the manufacturer, and all acceptance authorities, among other potential stakeholders.
This document does not impose a plan of execution to produce an AM part, though a digital thread is provided to establish a referenceable information workflow.
The requirements set forth in this document are based on the fabrication of a part using the PBF-LB/M (powder bed fusion-laser based/metal) process. While specific details directly relate to PBF-LB/M, generalized workflow requirements can be related to any AM process.

This document describes a classification of metallic blast-cleaning abrasives for the preparation of steel substrates before application of paints and related products.
It specifies the characteristics which are required for the complete designation of such abrasives.
This document applies to abrasives supplied in the "new" or unused condition only. It does not apply to abrasives either during or after use.
NOTE            Although this document has been developed specifically to meet requirements for the preparation of steelwork, the properties specified are generally appropriate when preparing other material surfaces, or components, using blast-cleaning techniques. These techniques are described in ISO 8504-2 [7].

This document specifies procedures for the evaluation of basic performance parameters of the radiographic film digitisation process, such as spatial resolution and spatial linearity, density range, density contrast sensitivity and characteristic transfer curve, which are applied in ISO 14096-2. These procedures can be integrated into the system software, and together with a standard reference film (see Annex B), used for quality control of the digitisation process. This reference film provides a series of test targets for performance evaluation. The test targets are suitable for evaluating a digitisation system with a basic spatial resolution down to 10 µm, a density contrast sensitivity down to 0,02 optical density, a density range of 0,5 to 4,5 and a film size capacity of (350 × 430) mm2.
This document does not address signal processing and display of the digitised data.

IEC 62541-9:2026 specifies the representation of Alarms and Conditions in the OPC Unified Architecture. Included is the Information Model representation of Alarms and Conditions in the OPC UA address space. Other aspects of alarm systems like alarm philosophy, life cycle, alarm response times, alarm types and many other details are captured in standards such as IEC 62682 and ISA 18.2. The Alarms and Conditions Information Model in this document, is designed in accordance with IEC 62682 and ISA 18.2. Annex C specifies a recommended mapping between OPC Classic Alarm & Events (A&E) servers to the model described in this document. Annex A describes recommended localized names for Alarm states. Annex B describes examples (e.g. Event sequences, Alarm areas in AddressSpace). This fourth edition cancels and replaces the third edition published in 2020. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) addition of "Comment" parameter to Alarm shelving methods;
b) addition of method that allows a client to get the members of a group, since it is possible that the AddressSpace does not expose instances of alarms;
c) addition of deadband properties for all limits in the limit AlarmType (from which all other types described in this issue are derived);
d) addition of text explaining the disabling of alarms is no longer supported in ISA 18.2 and that it is maintained in this document for backward compatibility, but that it is recommended that Alarm not be disabled;
e) addition of optional severities for limit alarms;
f) addition of new AlarmState variable type that can be used to collect alarm information for displays on graphics;
g) addition of SupportsFilterRetain property to improve Client filtering;
h) removal of ConditionSubClassId and ConditionSubClassNames from the conditiontype definition since they are now defined in BaseEventType.

IEC 60079-29-0:2025 specifies general requirements, test methods and acceptance criteria that apply to flammable, oxygen and toxic gas detection equipment intended to detect gases and vapours and to provide an indication, alarm or other output function for personnel or property protection in industrial and commercial applications. This document applies to the following gas detection equipment: – Gas detection equipment Type "FL" intended for the detection of flammable gases: • Type FL-Group I, in mines susceptible to firedamp; • Type FL-Group II, in locations other than mines susceptible to firedamp; and • Type FL-OP, open path gas detection equipment for flammable gases. – Gas detection equipment Type "O2" intended for the detection of Oxygen: • Type O2-DE, detection of oxygen deficiency or oxygen enrichment; and • Type O2-IN, inertisation as measuring function for explosion protection. – Gas detection equipment Type "TX" intended for the detection of toxic gases: • Type TX-SM, detection in areas for safety monitoring applications and typically using alarm signalling; • Type TX-HM, occupational exposure measurement in the region of occupational exposure limit values; and • Type TX-OP, open path gas detection equipment for toxic gases. This document is not applicable to equipment: – used for medical applications; – used only in laboratories for analysis or measurement; – used only for process monitoring or control purposes (such as a gas analyser); – used in the domestic environment; – used in environmental air pollution monitoring; – used for flue gas analysis; – used for sampling systems external to the gas detection equipment; – with samplers and concentrators such as sorbents or paper tape having an irreversible indication; – consisting of a passive optical receiver without a dedicated optical source; – equipment within the scope of IEC 60335-2-40 and IEC 60335-2-89. This first edition of IEC 60079-29-0 cancels and replaces the second edition of 60079-29-1 published in 2016 and its Amendment 1:2020, and the first edition of IEC 60079-29-4 published in 2009. In addition, IEC 60079-29-0 Type TX-SM cancels and replaces Type SM of the first edition of IEC 62990-1.

IEC 60095-8:2026 is applicable to lead acid batteries with a nominal voltage of 12 V, for automobile passenger cars applications, used as auxiliary energy storage and power source in vehicles, but not featuring the classical function of engine starting or cranking. This includes applications in battery-electric vehicles, as well as in vehicles with an internal combustion engine (ICE) that is started by another (12 V, 48 V or high-volt) battery. This document can be used for batteries with auxiliary or backup purposes.
This document specifies:
– the general requirements; and
– the essential functional characteristics, relevant test methods and results required for several classes of batteries in accordance with:
• the general type of application;
• the type of product; and
• the categories as defined in 4.1.