ICS - International Classification for Standards
ICS ICS Details
International Classification for Standards
Internationale Standard Klassifikation
International Classification for Standards
General Information
e-Library Subscription
Create subscription and get permanent access to documents within ICS - International Classification for Standards
Currently subscription includes documents marked with .We are working on making all documents available within the subscription.
IEC 62626-1:2023 is available as IEC 62626-1:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 62626-1:2023 applies to enclosed switches-disconnectors with rated voltages up to 1 000 V AC for repair and maintenance work or cleaning work in load circuits. Devices within the scope of this document are switch-disconnectors in accordance with IEC 60947-3 with specific additional requirements. Enclosed switch-disconnectors in this document are suitable for isolation in accordance with the IEC 60947 series and are not equipped with means for remote control or automatic switching to avoid unexpected or accidental start. These devices are not used for operational switching, for example quick start and stop, jogging. This second edition cancels and replaces the first edition published in 2014. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) update of this document based on IEC 60947-1:2020.
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 63119-1:2025 establishes a basis for the other parts of IEC 63119, specifying the terms and definitions, general description of the system model, classification, information exchange and security mechanisms for roaming between EV charging service providers (CSPs), charging station operators (CSOs) and clearing house platforms through roaming endpoints. It provides an overview and describes the general requirements of the EV roaming service system. The IEC 63119 series is applicable to high-level communication involved in information exchange/interaction between different CSPs, as well as between a CSP and a CSO with or without a clearing house platform through the roaming endpoint. The IEC 63119 series does not specify the information exchange, either between the charging station (CS) and the charging station operator (CSO), or between the EV and the CS. This second edition cancels and replaces the first edition published in 2019. This edition includes the following significant technical changes with respect to the previous edition: a) the scope is expanded to include differentiation between home and visited service provider roles and adds an explicit definition of roaming entity; b) adds definitions for "home charging service provider (home-CSP)", "visited charging station operator (visited-CSO)", and "charging detail record (CDR)", and expands related terms such as "service" and "roaming entity"; c) introduces abbreviation variants for "home-CSP" and "visited-CSO" in the terminology, aligning with North American and European conventions; d) updates the communication protocol stack by adopting a newer TLS version (upgraded from 1.2 to 1.3); e) system architecture and communication interfaces include detailed interactions between home-CSP and visited-CSO; f) adds a definition for "service" to cover a broader range of applications such as parking and reservation management; g) adds a distinction between "charging detail record (CDR)" and "service detail record (SDR)" and clarifies their relationship in the terminology; h) enhances the description of user credential transfer methods in communication interfaces with greater diversity; i) enhances the description of the mixed mode in the classification of roaming service models, emphasizing improved user experience through faster response times.
- Draft14 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 60300-3-10:2025 gives guidance to managers and technical and financial personnel on the basic principles of maintainability and maintenance activities that are applicable to any organization.
This document describes:
- the value and nature of maintainability and maintenance characteristics;
- the interfaces between maintainability and related dependability attributes of reliability, availability and supportability, as well as potential trade-offs that can be made through the interfaces during the life cycle of an item;
- the elements of maintainability and maintenance programmes;
- the application of maintainability and maintenance programmes throughout the life cycle;
- techniques to ensure maintainability and maintenance requirements are met;
- maintainability and maintenance data and information management.
This document is applicable to equipment, software, services, or structures, and gives guidance on matters of common interest to any business supplying, purchasing or sustaining products, services, or structures.
This second edition cancels and replaces the first edition published in 2001. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
- more guidance is included on establishing a maintenance programme;
- some guidance on support and supportability has been removed and has been moved to IEC 60300-3-14.
- Standard75 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62007-2:2025 specifies measuring methods for characterizing semiconductor optoelectronic devices that are used in the field of fibre optic digital communication systems and subsystems. This third edition cancels and replaces the second edition published in 2009. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) Modification of the definition of “optical fibre pigtail” in 3.1.3; b) Correction of an error in Formula (1) for relative intensity noise; c) Correction of an error in Formula (5); d) Correction of errors in the title of Figure 11 and the text of 4.9 (replaced "LD" with "LED"); e) Clarification of how to calculate the 1 dB compression in 4.9; f) Corrections of the circuit diagrams in Figure 2, Figure 5, Figure 11, Figure 17, Figure 18, Figure 19, Figure 20, and Figure 21; g) Clarification of the measurement setup in 5.10 (Figure 28).
- Draft39 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements related to dimensional, mechanical, and optical characteristics of thermoplastic films and tubes used during the manufacture of silage and designed to last at least one year for protecting fodder.
It specifies a classification for the durability of silage films and the test methods referred to in this document.
This document is applicable to transparent, black, white or coloured (e.g. black/white) thermoplastic silage films based on polyethylene, ethylene copolymer, EVOH and polyamide.
These films are intended for covering bunker silos, silage tubes or silage clamps for preserving forage. They protect the forage and preserve it from rain and air. These films are not intended to cover bales piles (e.g. straw bales and hay bales).
This document does not apply to silage films obtained by sealing two or more films in machine direction.
This document also provides guideline for installation, use and removal conditions of silage films. It also provides guideline for the conventional useful lifetime, as well as rules that allow evaluating the remaining use potential in the event of a failure before the normal end-of-use date.
- Standard22 pagesEnglish languagesale 10% offe-Library read for1 day
This document describes a method for the measurement of the swelling properties of hard coal using a dilatometer.
- Standard14 pagesEnglish languagesale 15% off
The purpose of this document is to specify requirements for marking, identification, leaktightness, electrical and operational safety and mechanical resistance for sanitary tapware with opening and closing controlled electronically.
The conditions of use for the supply system type are specified in Table 2:
[Table 2]
Annex B lists possible consequences of using a product outside its recommended operating range.
[Figure 1]
[Figure 2]
- Corrigendum4 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 60068-3-14:2025 describes a generic process for developing a climatic sequential test programme by sequencing test methods selected from the IEC 60068-2 series.
This generic process comprises a systematic approach to the development of a sequential environmental test programme.
A climatic sequential test is applicable to electrical, electromechanical or electronic equipment and devices, as well as their subassemblies, constituent parts and components. It can be customized according to specific product requirements and applications.
The process is designed for use by product designers, manufacturers and users.
The process is particularly relevant to electrical products which include components or materials that have the potential to degrade, as a consequence of environmental exposures.
- Standard23 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 60947-4-1:2023 is applicable to the following equipment:
- electromechanical contactors and starters including motor protective switching devices (MPSD and IMPSD);
- actuators of contactor relays;
- contacts dedicated exclusively to the coil circuit of the contactor or the contactor relay;
- dedicated accessories (e.g. dedicated wiring, dedicated latch accessory);
intended to be connected to distribution circuits, motors circuits and other load circuits, the rated voltage of which does not exceed 1 000 V AC or 1 500 V DC.
This fifth edition cancels and replaces the fourth edition published in 2018. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) objective in the scope;
b) instantaneous only motor protective switching device IMPSD (3.5.33);
c) kinds of equipment (5.2.1);
d) methods of overload protection of motors (5.2.6);
e) adoption of the AC-7d from IEC 61095:2023 (in 5.4.2);
f) separately mounted overload relay of a starter (in 5.7.3 b));
g) starter and contactor suitable for use downstream to basic drive module (6.1.2 w));
h) reference to IEC TS 63058 for environmental aspects (in 6.4);
i) wiring subject to movement (in 8.1.3);
j) use of voltage transient limiting device (8.1.18);
k) accessible parts subject to temperature limits (in 8.2.2.3);
l) reference to Annex X of IEC 60947-1:2020 for the co-ordination of MPSD with SCPD (8.2.5.4);
m) reference to IEC TR 63216 with different EMC environments (8.3.1);
n) reference to IEC TR 63201 for the embedded software design (8.4);
o) reference to IEC TS 63208 for cybersecurity aspects (8.5);
p) update and completion of the measurement method of the power consumption of the electromagnet (9.3.3.2.1.2);
q) update of Annex C including rational about AC-3e;
r) determination of the critical load current for photovoltaic applications (M.8.7).
- Standard191 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 60704-2-3:2025 applies to single unit electric dishwashers for household and similar use, with or without automatic programme control, for cold and/or warm water supply, for detachable or permanent connection to water supply or sewage systems, intended for placing on the floor against a wall, for building-in or placing under a counter, a kitchen worktop or under a sink, for wall-mounting or on a counter. This fourth edition cancels and replaces the third edition published in 2017. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) alignment to IEC 60704-1:2021, b) change of the position of the test sample in the test enclosure (aligned to IEC 60704 1:2021), c) detergent changed (aligned to IEC 60436:2025). This International Standard is intended to be used in conjunction with the fourth edition of IEC 60704-1:2021.
- Draft13 pagesEnglish languagesale 10% offe-Library read for1 day
This document establishes content for commercial specifications for drilling machines and foundation machines. It explains concepts related to their applications, working methods, machine types, and main components of the machines. This document is applicable to: — mobile drill rigs for civil and geotechnical engineering; — foundation equipment including piling machines; — diaphragm walling equipment; — jetting, grouting and injection equipment; — interchangeable auxiliary equipment. This document does not apply to: — machines specifically designed for mining application (e.g. rock drilling, raise boring, jumbo machines); — horizontal directional drilling (HDD) machines (covered by ISO 21467[ REF Reference_ref_6 \r \h 1]).
- Standard123 pagesEnglish languagesale 15% off
- Standard125 pagesFrench languagesale 15% off
- Amendment5 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 63322:2025 establishes security requirements of ME EQUIPMENT using high-activity SEALED RADIOACTIVE SOURCES, directly or indirectly, for medical treatment and other clinical procedures. ME EQUIPMENT containing SEALED RADIOACTIVE SOURCES that are defined as Category 1, 2 and 3 RADIOACTIVE SOURCES by IAEA are subject to this document. The object of this document is to specify requirements for the security of ME EQUIPMENT containing high-activity SEALED RADIOACTIVE SOURCES with the aim to minimize the risk of unauthorized access to the contained SEALED RADIOACTIVE SOURCES, and to serve as the basis for other standards. This document contains requirements for the MANUFACTURER of the ME EQUIPMENT and, separately, for the RESPONSIBLE ORGANIZATION regarding security at the location during use and storage. The requirements of this document apply when the SEALED RADIOACTIVE SOURCES are contained in the ME EQUIPMENT, i.e. from the time when the SEALED RADIOACTIVE SOURCES are inserted into the ME EQUIPMENT, during the INTENDED USE and when the ME EQUIPMENT is not being used for its INTENDED USE or taken out of regular use, until the equipment is being decommissioned, i.e. until all SEALED RADIOACTIVE SOURCES are permanently removed from the equipment.
- Standard68 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 60794-1-119:2025 applies to aerial optical fibre cables such as all-dielectric self-supporting (ADSS) cables, optical ground wire (OPGW) cables, and optical phase conductor (OPPC) cables that can be exposed to aeolian vibrations. This document defines the test procedures to establish uniform mechanical performance requirements relating to aeolian vibrations. See IEC 60794‑1‑2 for general requirements and definitions and for a complete reference guide to test methods of all types. This first edition cancels and replaces test method E19 of the first edition of IEC 60794‑1‑21 published in 2015. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to IEC 60794‑1‑21: a) addition of a system to maintain a constant cable tension during the test as well as means to measure the free loop antinode amplitude; b) definition of the cable load which is now fixed to 25 % of the rated tensile strength for OPGW/OPPC, or to the maximum installation tension (MIT) for ADSS cables; c) addition of the target free loop peak-to-peak antinode amplitude to the procedure. The quality of the aeolian vibration motion is done through the average antinode d) addition of fatigue damage and ovality changes of the optical core to 4.5.
- Draft11 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies conformance tests in the form of an abstract test suite (ATS) for a system under test (SUT) that implements an electric-vehicle communication controller (EVCC) or a supply-equipment communication controller (SECC) for all common requirements specified in ISO 15118-20 that are independent of a particular charging type (AC, DC, ACD, WPT charging). These conformance tests specify the testing of capabilities and behaviours of an SUT, as well as checking what is observed against the conformance requirements specified in ISO 15118-20 and against what the implementer states the SUT implementation's capabilities are. The capability tests within the ATS check that the observable capabilities of the SUT are in accordance with the static conformance requirements specified in ISO 15118-20. The behaviour tests of the ATS examine an implementation as thoroughly as practical over the full range of dynamic conformance requirements specified in ISO 15118-20 and within the capabilities of the SUT. A test architecture is described in correspondence to the ATS. The abstract test cases in this document are described leveraging this test architecture and are specified in descriptive tabular format covering the ISO/OSI layer 3 to 7 (network to application layers). In terms of coverage, this document only covers normative sections and requirements in ISO 15118-20. This document additionally refers to specific tests for requirements on referenced standards (e.g. IETF RFCs, W3C Recommendation, etc.) if they are relevant in terms of conformance for implementations according to ISO 15118-20. However, it is explicitly not intended to widen the scope of this conformance specification to such external standards, if it is not technically necessary for the purpose of conformance testing for ISO 15118-20. Furthermore, the conformance tests specified in this document do not include the assessment of performance nor robustness or reliability of an implementation. They cannot provide judgments on the physical realization of abstract service primitives, how a system is implemented, how it provides any requested service, or the environment of the protocol implementation. Furthermore, the abstract test cases specified in this document only consider the communication protocol and the system's behaviour specified in ISO 15118-20. Power flow between the EVSE and the EV is no prerequisite for the test cases specified in this document.
- Standard321 pagesEnglish languagesale 15% off
This document specifies a method which covers the determination of Gd2O3 content in UO2 fuel pellets, by X-ray fluorescence spectrometry.
Either wave dispersion X-ray fluorescence (WD-XRF) or energy dispersion X-ray fluorescence (ED-XRF) is applicable, however, this document states a method by using WD-XRF using Gd Lα-line.
This method has been tested for mass fractions of from 2 % to 10 % Gd2O3.
- Standard15 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 61095:2023 is available as IEC 61095:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 61095:2023 applies to electromechanical air break contactors for household and similar purposes provided with main contacts intended to be connected to circuits the rated voltage of which does not exceed 440 V AC (between phases) with rated operational currents less than or equal to 63 A for utilization category AC-7a, and 32 A for utilization categories AC‑7b, AC‑7c and AC-7d (expressed in rated power), and rated conditional short-circuit current less than or equal to 6 kA. This third edition cancels and replaces the second edition published in 2009. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) addition of requirements for screwless terminals;
b) addition of requirements for the switching of LED lamps. Contactors for domestic and similar applications can be used for controlling lighting loads which is increasingly using LED lamp technology. A specific category for contactors is created: AC-7d. Requirements and tests are added to cover this market development, mainly for making and breaking and conventional operational performance;
c) addition of requirements for contactors with electronically controlled electromagnet. Household contactors with electronically controlled electromagnet are available for years on the market. To fully cover such device, requirements and tests are added, dealing mainly with operating limits, behaviour in abnormal conditions, breakdown of components, EMC tests, etc.
d) embedded software. More and more contactors are incorporating electronic circuits with embedded software. A reference is provided to guide the design of the software.
- Standard146 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies requirements for electrically heated steam boilers manufactured from stainless steel specifically dedicated for generating steam for sterilizers and disinfectors.
This document covers only steam boilers that are heated by immersion heaters and which have a maximum allowable pressure (PS) of not greater than 6 bar, a maximum volume (V) of 1 000 litres and a product of PS ∙ V not greater than 3 000 bar ∙ l.
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
- Amendment8 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 60947-5-7:2024 states the requirements for proximity devices that correspond to the scope of IEC 60947-5-2:2019 with analog output (PDAO) and/or a digital output to transmit a corresponding digital value representing the detected sensing input. These devices can provide additional parameters.
This second edition cancels and replaces the first edition published in 2003. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) New structure;
b) Update and expansion of definitions on analog output properties;
c) Expanded performance requirements on analog output;
d) Update and new normative references;
e) Update of EMC requirements;
f) Harmonization with IEC 62828 series;
g) Harmonization with IEC 62683 and IEC 61987 definitions;
h) Harmonization with IEC 61131-2 requirements;
i) Update of the Annex A (former Annex G), Example of the determination of the conformity;
j) New Annex B, Overview tests and influence quantities;
k) New Annex C, Additional requirements for proximity switches with analog output incorporating a built-in communication interface complying with IEC 61131-9;
l) New Annex D, Main characteristics for proximity devices with analog output.
- Standard49 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard12 pagesEnglish languagesale 15% off
- Standard12 pagesFrench languagesale 15% off
IEC 63267-3-81: 2025 defines the dimensional limits of an optical interface for reference connectors with rectangular ferrules necessary to meet specific requirements for fibre-to-fibre interconnection of non-angled polished multimode reference connectors with rectangular ferrules intended to be used for attenuation measurements as defined in IEC 63267‑2‑2. Ferrule dimensions and features are contained in the IEC 61754 series of fibre optic interface standards.One grade of reference connector is defined in this document. The reference connector is terminated to restricted IEC 60793-2-10 A1-OM2b to A1-OM5b fibre at 850 nm band only. The geometrical dimensions and tolerances of the specified reference connector have been developed primarily to limit the variation in measured attenuation between multiple sets of two reference connectors, and therefore to limit the variation in measured attenuation between randomly chosen reference connectors when mated with connectors in the field or factory.
- Standard21 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the mechanisms and criteria to be applied for the selection and approval of the object identifier resolution system (ORS) operational agency and includes procedures that the operational agency is required to follow. It also addresses any future modification of the procedures and the procedures for any change of the operational agency. This document: — lists the object identifier (OID) nodes for which the operational agency is required to provide ORS support and gives the required level of support for these nodes; — gives the procedures by which lower-level nodes can apply for ORS support (class A, class B, or class C) and the role of the operational agency in providing these levels of support; — determines the basis for charges that can be levied for these levels of support.
- Standard8 pagesEnglish languagesale 15% off
IEC 60721-3-6:2025 classifies the groups of environmental parameters and their severities to which a product is subjected when installed aboard a ship.
Ships where electrotechnical products may be permanently or temporarily installed include
- ships propelled by mechanical means, including mobile offshore units, and
- ships not propelled by mechanical means, including sailing boats and life rafts.
The classes defined apply to all sizes of ship from pleasure craft to trawlers, ferry boats, icebreakers, cargo ships including tankers.
The areas in which ships normally navigate are
- inland waterways (canals, rivers, lakes etc.),
- coastal waters, and
- oceans.
Areas where ships navigate in ice are also included.
This second edition cancels and replaces the first edition, published in 1987, and constitutes a technical revision.
This edition includes the following significant changes with respect to the previous edition:
a) most classes have been replaced by completely new classes based on the use of new information obtained from referenced Technical Reports;
b) Table 1 through to Table 5 have been updated;
c) the content of Annex A and Annex B has either been incorporated into main body text or deleted.
- Standard19 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies methods for determining conformance to the security crypto suite defined in ISO/IEC 29167-11. This document contains conformance tests for all mandatory functions. Unless otherwise specified, the tests in this document are intended to be applied exclusively to RFID tags and interrogators defined in the ISO/IEC 18000 series using ISO/IEC 29167-11.
- Standard10 pagesEnglish languagesale 15% off
The present document provides detailed functional, service and accessibility requirements from the Human Factors perspective for the implementation of and compliance with the European Accessibility Act [i.27] which requires the provision of interoperable total conversation services wherever voice and video communication is available. It details how to provide an interoperable total conversation service, with voice, real-time text and sign language-supportive video communication media synchronized, as a context-optimized service, with no need for additional pre-registration. It also details viable fall-back options. Effective wireless coupling to hearing technologies, with the avoidance of interferences with assistive devices, and beyond, is also addressed. The necessary background information and specifications containing technical parameters is provided as informative annexes to the present document. The present document additionally provides guidance on how to implement the interoperable total conversation services for emergency communications so that the needs of all users, including people with disabilities, are met. As such the present document complements other standards developed in the area, such as EN 301 549 [1] and ETSI TS 101 470 [29].
- Standard83 pagesEnglish languagesale 15% off
- Standardization document83 pagesEnglish languagesale 10% offe-Library read for1 day
The present document defines measurement and monitoring of power, energy and environmental parameters for ICT equipment in telecommunications or data centre or customer premises. It defines the power, energy and environmental parameters monitoring interface of ICT equipment based on generic ETSI ES 202 336-1 [1] interface so that correlations can be made with ICT equipment parameters (traffic, flowrate, number of connected lines, radio setting, QoS KPI, etc.) in the Network Management System (NMS). Correlations of monitored data (power, energy consumption and environmental values) with other ICT equipment functional parameters and settings are not in the scope of the present document. The monitoring interface covers:
• Internal power consumption measurement on the ICT equipment powered in DC and AC.
• Power consumption measurement external to the ICT equipment (if not implemented internally, e.g. legacy equipment).
• Energy metering based on power consumption measurement.
• Environmental parameters of the ICT equipment (e.g. temperature at air inlet of equipment).
The present document defines:
• The minimum set of exchanged information required at the interface, including parameters such as measurement type (e.g. RMS), accuracy, range, etc. and settings such as data acquisition and transmission period, etc. This includes the data preparation, recording and transmission functions.
• The testing method of some parameters and functions.
Text tables in annexes A and B with data exchange described in "natural language"
- Standard28 pagesEnglish languagesale 15% off
- Standardization document28 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements relating to:
Steel 33CrMoV12 (1.8522)
Air melted
Softened
Forging stock
a or D ≤ 300 mm
for aerospace applications.
NOTE ASD-STAN designation: FE-PL1504.
Material number: 1.8522.
- Standard9 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 60436:2025 applies to electric dishwashers for household and similar use that are supplied with hot and/or cold water. The object of this document is to state and define the principal performance characteristics of electric dishwashers for household and similar use and to describe the standard methods of measuring these characteristics. This document is concerned neither with safety nor with minimum performance requirements. This fifth edition cancels and replaces the fourth edition published in 2015, and Amendment 1:2020. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) Implementation of a new reference machine, which better reflects modern dishwasher energy and water saving technologies. Its ability to function as a reference machine for the cleaning assessment was assessed in a Round Robin Test. b) Implementation of the new reference detergent type E, which better reflects market detergents formulations. It includes upgraded enzymes and a lower content of silicates to reduce the alkalinity which simplifies the world wide transportation by avoiding dangerous goods labelling and therefore improves the usage all over the world. c) Implementation of an alignment factor for the cleaning performance assessment as proposed in a scientific study done by an university to align test results of the previous version to the new version of this document with the new reference system described above. d) Introduction of replacements and alternatives for the pan and knives as the production of the current ones was stopped. e) Improvement of the room temperature control by a temperature measurement inside the dishwasher directly prior to the start of the test programme. f) Update of the weight of different load items and the specified ranges to anneal the requirements in the document to the actual weight of the items. g) Introduction of an updated method to assess low power modes providing a step-by-step measurement description and including new modes, e.g. network standby which are of increased importance for dishwasher offering additional services via internet connection. Additionally, reactions to different interactions with the appliance can be assessed in a better way and learnings of Round Robin Test are included. h) Inclusion of additional method for dishwasher testing which allows the assessment of variations of dishwasher units from one model. i) New requirements for the loading and handling instructions for tests institutes. j) Implementation of testing methodology for multi-compartment dishwashers. k) Improvement of ballast soil preparation process in Annex V.
- Draft158 pagesEnglish languagesale 10% offe-Library read for1 day
This document explains the application of harmonized and other EMF standards for placing on the market combined products with single or multiple radios to demonstrate conformity with the essential requirements laid down in article 3(1)(a) (health and safety of persons and domestic animals and safety of property) of the Radio Equipment Directive 2014/53/EU (RED) [1]. In particular this document addresses:
- the EMF conformity assessment of this type of product, including how to make use of EMF assessments already performed on each constituent product of the combined product and to identify the additional assessment necessary;
- the selection of the exposure limits for general public or for workers and test conditions.
The type of products covered by this document is a product consisting of the combination of two or more products where at least one of them is a radio equipment as defined in the RED.
Examples and types of products to be covered by this document include, but are not limited to, a combination of radio product(s) in radio product (e.g. Hi-Fi receiver with WPAN module integrated), combination of radio and non-radio product (e.g. domestic appliance with WLAN module integrated, radio-controlled lighting system, etc.).
- Technical report13 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft85 pagesEnglish languagesale 10% offe-Library read for1 day
This document applies to gangways for passenger vessels for inland navigation. It specifies the type, main dimensions and test conditions that can be observed for safety reasons.
NOTE A gangway serves as walkway between the passenger vessel and the shore.
- Standard8 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 63380-3:2025 defines the secure information exchange between local energy management systems and electric vehicle charging stations. The local energy management systems communicate to the charging station controllers via the resource manager. This document specifies the application of relevant transport protocols; in this case, SPINE (smart premises interoperable neutral-message exchange), SHIP (smart home IP), and ECHONET Lite. Other communication protocols can be defined in future editions
- Draft186 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft20 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 63267-3-61: 2025 defines the dimensional limits of an optical interface for reference connectors with 2,5 mm or 1,25 mm diameter cylindrical zirconia (ZrO2) ferrules necessary to meet specific requirements for fibre-to-fibre interconnection of non-angled polished multimode reference connections as defined in IEC 63267-2-2. Ferrule dimensions and features are contained in the IEC 61754 series of fibre optic connector interface standards. One grade of reference connector, Rm1, is defined in this document. The reference connector is terminated to restricted IEC 60793-2-10 using A1-OM2b to A1‑OM5b fibre in 850 nm band only. The geometrical dimensions and tolerances of the specified reference connector have been developed primarily to limit the variation in measured attenuation between multiple sets of reference connectors, and therefore to reduce the variation in measured attenuation between an arbitrarily chosen reference connector when mated with a connector in the field or factory.
This first edition and the first edition of IEC 63267-2-2 cancel and replace the first edition of IEC 61755-6-2 published in 2018. This edition constitutes a technical revision. The document includes the following significant technical changes with respect to the previous edition:
a) Definition of a reference grade, Rm1 interface;
b) Inclusion of A1-OM2b to A1-OM5b fibres;
c) Updates to normative references;
d) The addition of Annex A, which describes the attenuation test limits of reference grade Rm1 connectors to grade Bm connectors;
e) A new Annex B that describes the allowable fibre undercut.
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the list of product standards and common characteristics of electrical cables for use in the on-board electrical systems of aircraft at operating temperatures between -55 °C and 260 °C (except otherwise specified in product standards).
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements relating to:
Steel X3CrNiMoAl13-8-2 (1.4534)
Vacuum induction melted and consumable electrode remelted
Softened
Forging stocks
a or D ≤ 300 mm
for aerospace applications.
NOTE ASD-STAN designation: FE-PM1503
Material number: 1.4534
- Standard9 pagesEnglish languagesale 10% offe-Library read for1 day
The present document defines the Behaviour Types package of TTCN-3. TTCN-3 can be used for the specification of all types of reactive system tests over a variety of communication ports. Typical areas of application are protocol testing (including mobile and Internet protocols), service testing (including supplementary services), module testing, testing of APIs, etc. TTCN-3 is not restricted to conformance testing and can be used for many other kinds of testing including interoperability, robustness, regression, system and integration testing. The specification of test suites for physical layer protocols is outside the scope of the present document. TTCN-3 packages are intended to define additional TTCN-3 concepts, which are not mandatory as concepts in the TTCN-3 core language, but which are optional as part of a package which is suited for dedicated applications and/or usages of TTCN-3. This package defines types for behaviour definitions in TTCN-3. While the design of TTCN-3 package has taken into account the consistency of a combined usage of the core language with a number of packages, the concrete usages and guidelines for this package in combination with other packages is outside the scope of the present document
- Standard44 pagesEnglish languagesale 15% off
- Standardization document44 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the characteristics of UV laser printable DR family, single and multicore screened (spiral) and jacketed electrical lightweight cables for use in the on-board electrical systems of aircraft, at operating temperatures between −55 °C and 260 °C. Nevertheless, if needed, −65 °C is also acceptable as shown by cold test.
It is also possible to mark these cables by qualified compatible marking.
These markings are compliant with EN 3838.
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
This part of the EN 1366 series specifies a method of test and criteria for the evaluation (including field of direct application rules) of the ability of a penetration seal to maintain the fire resistance of a separating element at the position at which it has been penetrated by a service or services. Penetration seals used to seal gaps around chimneys, air ventilation systems, fire rated ventilation ducts, fire rated service ducts, shafts and smoke extraction ducts as well as combined penetration seals are excluded from this part of the EN 1366 series.
NOTE EN 15882-5 [6] deals with penetration seals including ducts and dampers.
Supporting constructions are used in this part of the EN 1366 series to represent separating elements such as walls or floors. These simulate the interaction between the test specimen and the separating element into which the sealing system is to be installed in practice.
This part of the EN 1366 series is intended to be used in conjunction with EN 1363 1.
The purpose of a test described in this part of the EN 1366 series is to assess the integrity and insulation performance of the penetration seal, of the penetrating service or services and of the separating element in the surrounding area of the penetration seal.
No information can be implied by the test concerning the influence of the inclusion of such penetrations and penetration seals on the loadbearing capacity of the separating element.
It is assumed that in each case the lintel above a penetration seal in the wall is designed in hot and cold state in a way that it does not apply any additional vertical load on the penetration seal.
It is not the intention of this test to provide quantitative information on the rate of leakage of smoke and/or hot gases or on the transmission or generation of fumes. Such phenomena are only noted in the test report in describing the general behaviour of test specimens during the test.
Tests in accordance with this part of the EN 1366 series are not intended to supply any information on the ability of the penetration seal to withstand stress caused by movements or displacements of the penetrating services.
The risk of spread of fire downwards caused by burning material, which drips e.g. through a pipe downwards to floors below, is at present excluded from this document.
Tests in accordance with this part of the EN 1366 series do not address any risks associated with leakage of dangerous liquids or gases caused by failure of pipes in case of fire.
Tests in accordance with this part of the EN 1366 series of pipe penetration seals for pipes of pneumatic dispatch systems, pressurized air systems, etc. simulate a situation where the systems are shut off in case of fire.
Explanatory notes to this test method are given in Annex H.
All values given without tolerances in this document are nominal ones unless otherwise specified.
All pipe diameters are outside diameters unless otherwise specified.
- Corrigendum2 pagesEnglish languagesale 10% offe-Library read for1 day
The present document gives guidelines for hosting accessible ETSI meetings on ETSI premises, those of ETSI members, or in public environments (e.g. conference centres). It proposes changes to the meeting registration procedure on the ETSI portal allowing participants to register accessibility requirements. It provides a resource collection that links to the most pertinent existing sign language interpreter databases and additionally includes a collection of recommended tools for speech-to-text tools and services, to help make meetings accessible for deaf and hard-of-hearing participants. It further includes a comparison of accessibility features of available meeting tools, recommendations for tool selection, an evaluation of the accessibility of joint editing and presentation tools and related recommendations for ETSI and for meeting hosts.
- Standard84 pagesEnglish languagesale 15% off
- Guide84 pagesEnglish languagesale 10% offe-Library read for1 day
The present document defines power feeding solutions for 5G, converged wireless and wireline access equipment and network, taking into consideration their enhanced requirements on service availability and reliability, the new deployment scenarios, together with the environmental impact of the proposed solutions. The minimum requirements of different solutions including power feeding structures, components, backup, safety requirements, environmental conditions are also defined. The present document is applicable to powering of both mobile and fixed access network elements, in particular on equipment that have similar configurations and needs. The development of 5G networks will create a new scenario in which the density of radio cells will increase considerably, together with the increase of wireline network equipment that are going to be installed in the vicinity to the users, thereby creating the need to define new solutions for powering that will be environmentally friendly, sustainable, dependable, smart and visible remotely. The -48 V DC, up to 400 V DC local and remote power solutions defined respectively in ETSI EN 300 132-2 [2], ETSI EN 302 099 [i.10] and ETSI EN 300 132-3 [3] or Recommendation ITU-T L.1200 [i.13] will be considered as the standards in force for power facilities, together with IEEE 802.3 [i.18] (PoE).
- Standard43 pagesEnglish languagesale 15% off
- Standardization document43 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements relating to:
Steel X15CrNi17-3 (1.4057)
Air melted
Softened
Forging stock
a or D ≤ 300 mm
for aerospace applications.
NOTE ASD-STAN designation: FE-PM3901
Material number: 1.4057
- Standard9 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the irradiation equipment using ultraviolet light emitting diode (UV-LED) and optical radiometry for testing the performance of semiconducting photocatalytic materials. The UV-LED irradiation equipment specified in this document uses UV-LEDs having a peak wavelength of 365 nm in the UV-A range and applies for a semiconductor photocatalyst exhibiting a photocatalytic function at this wavelength. This document applies only to irradiation equipment using UV-LED. ISO 10677[ REF Reference_ref_2 \r \h 2 08D0C9EA79F9BACE118C8200AA004BA90B0200000008000000100000005200650066006500720065006E00630065005F007200650066005F0032000000 ] is applicable for equipment using conventional UV light sources such as fluorescent lamps.
- Standard11 pagesEnglish languagesale 15% off
This document specifies certain characteristics of the essential oil of lavandin Abrial (Lavandula x intermedia Emeric ex Loisel. ‘abrial’) (ex Lavandula angustifolia Mill. x Lavandula latifolia Medik. ‘abrial’), in order to facilitate assessment of its quality.
- Standard8 pagesEnglish languagesale 15% off
- Standard8 pagesFrench languagesale 15% off
This document describes a dynamic dual-task method that quantitatively measures human-performance degradation on a primary driving-like task while a secondary task is being performed. The performance measures of the method indicate the visual-manual and cognitive secondary-task demand associated with visual-manual or auditory-verbal secondary task engagement while driving. This document defines key terms and parameters for the assessment of BT + DRT. It provides guidelines and minimum requirements on equipment and procedures to plan evaluation trials, specify (and install) data capture equipment, conduct a study, analyse, interpret, and report metrics indicating visual-manual and cognitive secondary-task demand using the BT + DRT. The metrics and definitions described in this document provide a common source for the assessment of visual-manual and cognitive task demand induced by different IVIS while driving. The BT + DRT is applicable to standardized experiments in laboratory-based settings. Data collection and analyses according to this document allow comparisons across different secondary tasks. In contrast, this document does not apply to the measurement of primary (driving) task demand. This document can be applied to both original equipment manufacturer (OEM) and after-market in-vehicle systems, and to permanently installed as well as portable systems.
- Standard11 pagesEnglish languagesale 15% off
This document specifies primary and secondary dimensions for specified types of garments to establish a size designation system based on body dimensions (as defined in ISO 8559-1).
- Standard41 pagesEnglish languagesale 15% off
This document provides guidance on how to use modelling in privacy engineering. It describes categories of models that can be used, the use of modelling to support engineering, and the relationships with other references, including International Standards on privacy engineering and on modelling. It provides high-level use cases describing how models are used.
- Technical specification32 pagesEnglish languagesale 15% off
This document specifies the principal method for out-of-plane laser shearography non-destructive testing (NDT) of fibre-reinforced polymer (FRP) composites. This document is applicable to both monolithic and sandwich FRP laminate constructions, with or without curved surfaces, fibre-reinforced thermoset and thermoplastic matrix composites incorporating uni- or multi-directional reinforcements in either a continuous or discontinuous format; including but not limited to woven fabrics, stitched fabrics, short fibre, or particulate filled, honeycomb or foam cores, as well as combination or hybrid reinforcements. This document is not applicable to variations on this basic configuration.
- Standard22 pagesEnglish languagesale 15% off